CONFIG GNS3

  • View
    227

  • Download
    11

Embed Size (px)

Text of CONFIG GNS3

QUEMU

QUEDA TAL COMO ESTA

Arrastramos las imagens que requerimos routers y switch Seleccionamos los 2 routers y click derecho sobre uno de ellos y elegimos configure

Y nos sale el siguiente menu

Vamos a slot y cambiamos donde dice wic 0 y elegimos WIC-2T

Apply y OK

Luego damos click en add link

Damos click sobre alguno de los objetos y nos muestra las interfaces para seleccionar , elegimos y apare automticamente el cable para conectar a otro objeto a alguna de sus interfaces

Una vez realizados las conexiones damos click en el icono que tiene la forma de un triangulo verde

Al aparecer todos los puntos en verde significa que la estructura esta trabajando con normalidad. Luego damos click en le botn consoletoalldevice

Y aparece las siguientes ventanas

Nos percatamos que el rendimiento es psimo del S.O. por lo cual, primero damos click en el botn add link para que vuelva a su icono original, luegoselecionamos una de los routers y damos click en Idle PC , aparece un cuadro y damos YES

Aparece un cuadro como el de la imagen

Damos click en la pestaa y seleccionamos alguno de los nmeros que empiezan con * damos aply y luego OK y con esto se reduce el consumo del CPU.

Username: cisco Password:cisco R1>enable Password:class R1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R1(config)#interface f0/0 R1(config-if)#

R1 con0 is now available

Press RETURN to get started.

ACCESO RESTRINGIDO - SOLO PERSONAL AUTORIZADO - TODAS LAS CONEXIONES SON REGISTRADAS banner motd

User Access Verification

Username: cisco1 Password: R1>R1> % Unknown command or computer name, or unable to find computer address R1>R1>Password: % Unknown command or computer name, or unable to find computer address R1>% Unknown command or computer name, or unable to find computer address ^ % Invalid input detected at '^' marker.

R1>R1>Password: % Unknown command or computer name, or unable to find computer address R1>% Unknown command or computer name, or unable to find computer address ^ % Invalid input detected at '^' marker.

R1>R1>R1>enable % Unknown command or computer name, or unable to find computer address R1>% Unknown command or computer name, or unable to find computer address ^ % Invalid input detected at '^' marker.

R1>R1>Password: % Unknown command or computer name, or unable to find computer address R1>% Unknown command or computer name, or unable to find computer address ^ % Invalid input detected at '^' marker.

R1>R1>R1#conf term ^

% Invalid input detected at '^' marker.

R1> ^ % Unknown command or computer name, or unable to find computer address R1>% Invalid input detected at '^' marker. ^ % Invalid input detected at '^' marker.

R1> R1>R1>Enter configuration commands, one per line. End with CNTL/Z. ^ % Invalid input detected at '^' marker.

R1>

^

% Unknown command or computer name, or unable to find computer address R1>% Invalid input detected at '^' marker. ^ % Invalid input detected at '^' marker.

R1> R1>R1>R1(config)#username cisco password cisco ^ % Invalid input detected at '^' marker.

R1> ^ % Unknown command or computer name, or unable to find computer address R1>% Invalid input detected at '^' marker. ^ % Invalid input detected at '^' marker.

R1>

R1>R1>R1(config)#username cisco1 password cisco1 ^ % Invalid input detected at '^' marker.

R1> ^ % Unknown command or computer name, or unable to find computer address R1>% Invalid input detected at '^' marker. ^ % Invalid input detected at '^' marker.

R1> R1> R1>enable Password: Password: R1#disable R1>

R1 con0 is now available

Press RETURN to get started.

ACCESO RESTRINGIDO - SOLO PERSONAL AUTORIZADO - TODAS LAS CONEXIONES SON REGISTRADAS banner motd

User Access Verification

Username: cisco Password: R1>enable Password: R1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R1(config)#interface f0/0 R1(config-if)# R1# *Mar 1 00:40:09.047: %SYS-5-CONFIG_I: Configured from console by cisco on console R1# R1#ip address 192.168.1.1 255.255.255.0 ^ % Invalid input detected at '^' marker.

R1#enable R1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R1(config)#interface f0/0 R1(config-if)#ip address 192.168.1.1 255.255.255.0 R1(config-if)#no shut R1(config-if)# *Mar 1 00:43:13.567: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up

*Mar 1 00:43:14.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up R1(config-if)#exit R1(config)#line console 0 R1(config-line)#logg % Incomplete command.

R1(config-line)#logging syn R1(config-line)#logging synchronous R1(config-line)#interface s0 % Incomplete command.

R1(config)#interface s0/0 R1(config-if)#ip address 192.168.2.1 255.255.255.0 R1(config-if)#no shutdown R1(config-if)# *Mar 1 00:46:02.807: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up R1(config-if)# *Mar 1 00:46:03.811: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up R1(config-if)# *Mar 1 00:46:26.199: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down R1(config-if)# *Mar 1 00:49:56.199: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up R1(config-if)#

R1 con0 isnowavailable

Press RETURN to get started.

*Mar 1 00:56:01.255: %SYS-5-CONFIG_I: Configured from console by cisco on console

Connected to Dynamips VM "R2" (ID 1, type c2691) - Console portPress ENTER to get the prompt.

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: % Please answer 'yes' or 'no'. Would you like to enter the initial configuration dialog? [yes/no]: % Please answer 'yes' or 'no'. Would you like to enter the initial configuration dialog? [yes/no]: n

Would you like to terminate autoinstall? [yes]:

Press RETURN to get started!

*Mar 1 00:00:04.347: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0 , changed state to up *Mar 1 00:00:04.347: %LINEPROTO-5-UPDOWN: Line protocol on Interface IPv6-mpls, changed state to up *Mar 1 00:00:04.351: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up *Mar 1 00:00:04.355: %LINK-3-UPDOWN: Interface Serial0/1, changed state to up *Mar 1 00:00:04.359: %LINK-3-UPDOWN: Interface Serial0/2, changed state to up *Mar 1 00:00:04.363: %LINK-3-UPDOWN: Interface Serial0/3, changed state to up *Mar 1 00:00:05.351: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up *Mar 1 00:00:05.355: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up *Mar 1 00:00:05.359: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2, changed state to up

*Mar 1 00:00:05.363: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3, changed state to up *Mar 1 00:00:33.107: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to down *Mar 1 00:00:33.131: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2, changed state to down *Mar 1 00:00:33.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3, changed state to down *Mar 1 00:01:14.883: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down *Mar 1 00:01:15.139: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down *Mar 1 00:01:15.703: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down *Mar 1 00:01:15.883: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern et0/1, changed state to down *Mar 1 00:01:16.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern et0/0, changed state to down *Mar 1 00:01:16.703: %LINK-5-CHANGED: Interface Serial0/0, changed state to administratively down *Mar 1 00:01:16.735: %LINK-5-CHANGED: Interface Serial0/1, changed state to administratively down *Mar 1 00:01:16.739: %LINK-5-CHANGED: Interface Serial0/2, changed state to administratively down *Mar 1 00:01:16.743: %LINK-5-CHANGED: Interface Serial0/3, changed state to administratively down *Mar 1 00:01:19.339: %IP-5-WEBINST_KILL: Terminating DNS process *Mar 1 00:01:20.627: %SYS-5-RESTART: System restarted -Cisco IOS Software, 2600 Software (C2691-ADVENTERPRISEK9-M), Version 12.4(25), R ELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Tue 21-Apr-09 10:48 by prod_rel_team *Mar 1 00:01:20.639: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start Router>y Translating "y"...domain server (255.255.255.255)

(255.255.255.255) Translating "y"...domain server (255.255.255.255) % Unknown command or computer name, or unable to find computer address Router> Router>ena Router#hostname R2 ^ % Invalid input detected at '^' marker.

Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R2 R2(config)#

R2 con0 is now available

Press RETURN to get started.

*Mar 1 00:12:29.755: %SYS-5-CONFIG_I: Configured from console by console R2> R2> R2> R2> R2>

R2>

R2 con0 is now available

Press RETURN to get started.

R2>enable R2#configure terminal Enter configuration commands, one per line. End with CNTL/Z. R2(config)#line console 0 R2(config-line)#logginsynchronous R2(config-line)#interface f0/0 R2(config-if)#ip address 192.168.3.1 255.255.255.0 R2(config-if)#no shutdown R2(config-if)# *Mar 1 00:47:51.399: %LINK-3-UPDOWN: Interface FastEtherne