INCLUDED CONTENTS12345

Fuselage CoverMain Frame / CageMain Blades (x 4)3.7 Rechargeable Lithium Battery

Thank you for your purchase of the Odyssey Turbo Runner.You’re just moments away from creating stunning aerial acrobatics!

x4

USB Charging Cable6 Radio Transmitter

CLIMBING & ROLLING QUADCOPTERCLIMBING & ROLLING QUADCOPTER

Speed Setting: High Speed Mode - Press the button then you will hear a double beep.Low Speed Mode - Press the button then you will hear a single beep.

Fly/Run Mode:Fly Mode - Press the button then you will hear a double beep.Run Mode - Press the button then you will hear a single beep.

If the Radio Control Transmitter will not be used or stored for extended periods of time, please remove the batteries.

Unscrew the screw holding the battery lid to the body. Then lightly pull the clip to pull the lid away from the transmitter body.

Insert 4xAA batteries into the battery compartment, making sure to match the polarities. Then replace the lid and firmly tighten the screw to secure the battery compartment.

WARNING

CAUTION

Please check the AA batteries routinely. If the AA batteries are left within the Radio Control Transmitter, potential leakage and/or corrosion may occur which can damage the transmitter and create a fire hazard.

NOTICEPlease use 4 AA batteries. Use the polarity markings to install in the correct orientation.Do not mix different batteries or battery types.

Fly/Run Mode

Speed Setting

Automatic Mode

360°Flip

Forward/Backward &Left/Right JoystickThrottle Stick • Up/Down & Left Right

Trim Adjustment for Forward/Backward

Trim Adjustment for Side MotionTrim Adjustment for Left/Right Turns

2.4 Ghz Antenna

Power Switch

Power Light

RADIO CONTROL TRANSMITTER • BATTERY INSTALLATION

RADIO CONTROL TRANSMITTER • FUNCTIONS

The battery may be hot if being disconnected right after use. If hot, then wait a few minutes to let the battery cool down. When charging do not leave the battery unattended to keep from overcharging. Overcharging the battery will lead to battery damage.

CAUTION

When charging with the included USB cable the LED light will light up red, indicating it is charging. Once charging is complete, the LED light will turn off.

NOTICE

If the Turbo Runner is not going to be used for extended periods of time, please disconnect the battery from the Quadcopter to avoid damage to the battery or the Quadcopter unit.

NOTICE

The FLX Crawling Copter battery comes partially charged and is ready to fly. Skip to Remote Control Battery Installation section and use your Quadcopter now. Use this charge completely before charging the FLX Crawling Copter battery for the first time.

WE RECOMMEND!

Locate the battery underneath the unit. Carefully disconnect the power cable underneath the Turbo Runner as shown in the photo. Do not pull the battery by the wires as the wires may break off of the battery housing.

Connect the battery’s power cable to the end of the USB charging cable. Then connect the USB end of the charging cable to a USB port like on a computer or a USB phone charger.Please note: Not all USB ports provide power. Typically, only ports mounted on a computer and not through a peripheral will provide enough power for charging.

CHARGING THE BATTERY FOR THE FLX CRAWLING COPTER

ASCEND/DESCEND

LEFT/RIGHT

FORWARD/ BACKWARD MOTION & STRAFING

Push the left joystick (throttle) up to ascend. Ease the throttle (left stick) downwards in order to make the Turbo Runner go lower in altitude.

To TURN LEFT or RIGHT:Push the left joystick to the left to turn left or right to turn right.

To GO FORWARD & BACKWARDPush the right joystick up to make the quadcopter fly forward. Push it down to make the quadcopter fly backward.

To STRAFE LEFT & RIGHT:Push the right joystick to the left to make the unit go sideways to the left without turning (this is called strafing). Push the right joystick to the right to make the unit go sideways to the right without turning.

NOTE: Strafing is useful when you want to make the unit go side to side or go around obstacles where it might be difficult to turn or rotate the unit.

Connect the battery on the unit. Then lay the unit flat on the ground and you will see the two LEDs flashing red on the Turbo Runner Fuselage Cover.

Power on the Radio Control Transmitter. Push the left joystick all the way to the top and then again back down to begin pairing. If paired successfully, the transmitter will make a beep sound and the LEDs on the unit will stop flashing. You are now in flight mode.

TO RESET THE UNIT1. Lay the unit flat on a level surface or the ground. 2. Push both the left and the right joystick to the bottom right corner position until the LEDs on the unit begin to flash.3. The RESET is complete when the LEDs on the unit stop flashing.

Please note, when resetting the unit using the controller, the quadcopter must be completely still and its main body must be horizontally leveled.

GOING TO FLIGHT SCHOOL • CONTROLLING THE TURBO RUNNER QUADCOPTER UNIT

PREPARING YOUR UNIT TO FLY • PAIRING YOUR REMOTE / RESETTING YOUR UNIT

TURBO RUNNER • ADVANCED FEATURES

Press the AUTOMATIC mode button, and it will fly in a circle on autopilot.

When the quadcopter flies close enough to a smooth wall, you can press the FLY/RUN mode button to switch it to ROLLING mode. It will almost move like a car climbing a wall or rolling on the ceiling!

When you push the left joystick, the unit will turn left; when you push it to the right, the unit will turn right. To move forward and backward, push the right joystick up to move forward or down to move backward.

When the unit is on the ground, you can switch it from FLYING to ROLLING mode to operate it on the ground and have it roll instead of fly.

NOTICE: If the unit moves forward or backward at a slight angle, adjust the trim setting (under the right joystick) to have it roll in a straight line.

AUTOMATIC MODE

WALL CLIMBING MODE

GROUND MODE

360°Flip

TRIM ADJUSTMENTS ON THE RADIO CONTROL TRANSMITTER

Correct trim adjustment is required for error and erractic-free flying of the quadcopter. The adjustment is simple to do on the radio control transmitter, but it requires some patience. Please follow the instructions precisely. For best results, move the throttle up and raise the quadcopter approximately 2-3 feet (0.5-1 meter) in altitude.

If the quadcopter moves by itself slowly or quickly to the left or right:Press the trim control for turning incrementally in the opposite direction of movement

If the quadcopter slides by itself slowly or quickly to the side:Press the trim control for rotation incrementally in the opposite direction of movement

If the quadcopter moves by itself slowly or quickly forwards or backwards:Press the trim control for forwards and backwards flight incrementally in the opposite direction of movement

360º FLIPPress the 360º FLIP button on the top right of the transmitter to have it perform amazing, acrobatic 360º flips!

FLYING SAFE • BE AWARE OF YOUR ENVIRONMENT and SURROUNDINGS

TECHNICAL SPECFICATIONS & PARAMETERS

TROUBLESHOOTING

PROBLEM

BlinkingUnit LED

POSSIBLE SOLUTIONS

Always fly on a sunny, bright day with as little wind as possible. Flying in extreme heat or cold can adversely affect your flying control and response of the vehicle.

After connecting the battery, place the quadcopter on the ground. Please wait for approximately 5-7 seconds to allow the digital gyro to electronically stabilize. Push the throttle up and then back down to pair the radio control transmitter to the Turbo Runner. The lights will stop blinking and now you are all set to fly.

Length: 95 mmWidth: 100 mmHeight: 100 mm

Charging Time: Approximately 60 minutesFlying Time: Approximately above 5-6 minutesRadio Control monitor viewing distance limit: approx. 50 meters

Check to make sure the power switch is in the ON position. If set to OFF, move to the ON position.

Check to make sure the batteries are installed correctly. Check to make sure they match the polarity markings.

When the LED on the unit begins to blink, this indicates a low battery condition. Please charge the unit again.

If the batteries are installed correctly, they may be exhausted. Replace with new and fresh batteries.

If there isn’t any accurate control of the vehicle, make sure of the following:

• Make sure the radio control transmitter is set to the ON position• Make sure the battery on the vehicle is installed correctly• The vehicle may fly erratically if wind conditions are too strong. Fly the vehicle under calm conditions.• Make sure the radio control transmitter has paired correctly with the vehicle. If not, power down the vehicle and the radio control and start over.

The rotor speed may be too slow to lift the quadcopter sufficiently. Make sure the throttle is being raised sufficiently. If the unit still does not go up or goes up too slowly, the battery of the quadcopter might be too discharged for safe or satisfactory operation. Charge the battery before continuing to fly the unit.

If the unit fails to go up in altitude or goes up too slowly, try the following:

20855 NE 16 Avenue No. C22 • Miami, FL 33179, United States

For Customer Service please email: Care@OdysseyToys.comPlease note the units model number and name in your email.

Extra Parts Available! Visit Odyssey online to order: • Extra Batteries • New rotor blades

Model no. ODY-1012RB / ODY-1012GY • Turbo Runner Rolling Quadcopter

www.OdysseyToys.com

CAUTIONS & WARNINGS

CARE & MAINTENANCE

• Suitable for ages 14 and up. Adult supervision is always recommended.• This product contains small parts which are a choking hazard. Keep away from small children.• Keep Quadcopter at least 10 feet away during use.• Accurately assemble the quadcopter and fly it under the guidelines of this manual. Small parts should be installed by an adult.• Manufacturers and dealers disclaim all responsibility for damage caused by misuse. • Keep hands, hair and loose clothing away from rotors when powered on to to prevent damage to the vehicle or serious injury to oneself or others around.• The quadcopter should never be flown in high winds in excess of 5 MPH or near a pool.• Never leave the device unattended when being charged.

• Do not submerge the unit in any liquids. • Keep the unit dry. • Disconnect the unit and monitor from USB power sources when not in use.• Do not place the unit near powerful, un-shielded magnets.• Do not expose the unit to extreme hot or cold temperatures.• Do not hit, drop, or smash the unit with extreme force. • Do not disassemble the unit for any reason.

NOT FOLLOWING THESE PRECAUTIONS WILL VOID YOUR WARRANTY.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.