CE ORIGINAL MANUAL SCAMPER S200 XL VERSION CE 1.1 EN€¦ · CE ORIGINAL MANUAL SCAMPER S200 XL VERSION CE 1.1 EN 4 Introduction Thank you for choosing LACROS. This manual is written

CE ORIGINAL MANUAL SCAMPER S200 XL

VERSION CE 1.1 EN

1


VERSION CE 1.1 EN

2

SAFETY AND SHINGA

SAFETY COMES ALWAYS FIRST. READ THE FOLLOWING SAFETY ADVICES THOROUGLY REGARDING OUR (ELECTRICAL)

BIKES:

1. LACROS E-BIKES ARE EQUIPPED WITH AN ELECTRIC MOTOR. IT IS OF GREAT CONCERN TO LEARN HOW TO USE THE

E-BIKE PROPERLY AND DRIVE IN COMPLIANCE WITH THE LOCAL TRAFFIC REGULATIONS. WE ADVICE FIRST TO DO

SOME PRACTICE RUNS ON EASY ROADS AND LESS TRAFFIC TO GET FAMILIAR WITH THE E-BIKE

2. DON’T STAND ON THE PEDALS WHEN YOU START RIDING THE BIKE. SIT FIRST ON THE SADDLE AND START

PEDALLING

3. RIDE PREFERABLY THE FIRST FEW DRIVES WITHOUT THE ELECTRIC MOTOR TO GET FAMILIAR WITH THE E-BIKE.

START GRADUALLY WITH LOW POWER SETTING AND INCREASE ONCE YOU ARE FAMILIAR WITH THE E-BIKE

4. THE LACROS E-BIKES ARE TESTED BY US. TESTS TAKES APPROXIMATELY 15MIN ACCORDING OUR PROTOCOL.

HOWEVER, IF IN ANY DOUBT REGARDING THE BIKE AND THE ELECTRONIC INSTALLATION, CONTACT US

IMMEDIATELY

5. DO NOT EXPOSE BATTERY AND CHARGER IN DIRECT SUN. BATTERY IS PROTECTED AGAINST HEAT, BUT

OVERHEATING MUST BE AVOIDED AT ALL TIMES

6. USE ONLY THE ORIGINAL CHARGER SUPPLIED WITH THE E-BIKE TO AVOID DAMAGE TO THE BATTERY AND THE

ELECTRONIC INSTALLATION

7. BRAKES ARE PROVIDED WITH “ABS” SAFETY. WHEN YOU BRAKE (AND STOP PEDALLING), THE ELECTRO MOTOR

WILL STOP

8. WE ADVICE TO USE A HELMET WHEN RIDING THE BIKE

LACROS E-BIKES ARE MANUFACTURED ACCORDING EUROPEAN GUIDELINES AND REGULATIONS. FOR QUESTIONS

AND/OR REMARKS, YOU CAN CONTACT US ON THE BELOW MENTIONED CONTACT INFORMATION.

WE ARE ALWAYS AVAILABLE FOR OUR CUSTOMERS:

E-MAIL: [email protected]

TELEPHONE: +3173 203 2487

WITH KIND REGARDS,

Ton van den Oetelaar

CEO Shinga BV

* Shinga follows guidelines NEN-EN 15194: 2015 Ontw. (Fietsen - Elektrisch ondersteunde fietsen - EPAC Fietsen) /

NEN-EN-ISO 4210-1: 2014 / EN ISO 12100: 2010, see page 13


VERSION CE 1.1 EN

3

CONTENT

Introduction .......................................................................................................................................................... 4

Safety tips .............................................................................................................................................................. 4

! Safety regulations ! ............................................................................................................................................. 5

Manual SCAMPER S200 XL .................................................................................................................................... 6

Important notice: .................................................................................................................................................. 6

Pre-ride checks: ..................................................................................................................................................... 6

Easy start up: ......................................................................................................................................................... 7

Charging/removing battery: .................................................................................................................................. 9

General information about the E-Bike:................................................................................................................ 10

Technical specifications: ...................................................................................................................................... 12

Frame number is located on front fork. .............................................................................................................. 12

Contact information Shinga BV ........................................................................................................................... 12

EU Declaration of Conformity concerning machines ........................................................................................... 13


VERSION CE 1.1 EN

4

Introduction Thank you for choosing LACROS. This manual is written for convenient use and to safeguard the use of the E-Bike. After

reading this manual you can get familiar about the functions and proper use of our E-bikes. The technical design of the E-

Bikes are reliable, we use quality parts and together with our high standard of service, we can provide you with an E-bike

which is easy to use, reliable, all together with a high range. Therefore an ideal transport for all our customers around the

globe. Your opinion is highly appreciated to improve our products and to create a perfect bike with the latest technology.

We strive to produce an E-bike that meets the requirements and needs of our customers.

Safety tips 1. Check on a regular basis for external damage before you use the E-Bike.

2. Drivers can reduce the possibility of accidents by:

a. Wearing light clothes;

b. Use of (head)lights;

c. Keep distance with other vehicles;

d. Comply to local traffic regulations;

e. Reach hand out to the direction before you turn;

f. Never use one hand for a longer time to steer. Use both hands;

g. Never ride the bike with 2 or more persons;

h. Do not brake extreme during rain or wet road.

3. Caution with loose clothes.

4. Caution when wearing long overcoat, long dresses during step up/out and drive.

5. Carrying goods/baggage;

a. Do not exceed payload more than 25 Kgs and a total weight of 140 Kgs with the E-Bike, driver weight and goods;

b. Secure goods/baggage before you ride;

c. Preferably no baggage on the steer to avoid swaying of the E-Bike.

6. Do not use Pressure washer to avoid electrical damage.

7. Maximum of 10 Kgs static load of the steer. Do not use child seat up front.

8. Baggage carrier is only to be used for baggage.


VERSION CE 1.1 EN

5

! Safety regulations ! 1. To ensure safe driving, it is important to read the instructions. For any discrepancy in our manual, contact us. 2. Comply to local traffic regulations , do not ride with 2 or more persons, reduce speed during bad weather, wet road or

down/uphill. 3. The E-bike can be used during rain and snow, but it must not be immersed in water to prevent damage to the motor,

battery and electrical parts. 4. Repair must only be done by Shinga or its approved agent with parts approved by Shinga. 5. Never lend the E-Bike to persons not familiar with E-bikes to prevent accident and injury. 6. Do not drink and drive. Stay focus while riding. 7. Maximum payload is 140 kgs. 8. Exceeding payload may decrease safety and increase damage to the E-Bike. 9. Do not modify the E-bike yourself. This will void the warranty. 10. The maximum speed is set to 25Km/h. It is not permitted to increase the maximum speed. If changes are made in the

settings, the driver will be liable for any accidents occurred. 11. When the front fork or steer is damage after an accident, it must be replaced to insure the bike’s integrity.


VERSION CE 1.1 EN

6

Manual SCAMPER S200 XL The Scamper is available in different specification. This manual apply to these specifications:

Battery: PANASONIC 36V 11.6 AH or 36V 17 AH.

Electric motor: 250W BAFANG in rear wheel.

Important notice: According to the Dutch regulations an electric bicycle must be equipped with the following:

Two independent functioning brakes

Head light

Rear light

Spoke reflector, reflective tires or rim

Pedals with reflectors

Front reflector (if not build in head light)

Rear reflector

Pre-ride checks: Check on a regular basis the following components:

Brakes

Spokes

Lights

Bike bell

Tire pressure between 3.5-4.0 Bar

Tire profile

Locked battery

Electrical system operations

Adjust and secure the saddle and steering with the clamp.

On the steering and saddle bar, a ribbed line is engraved.

This indicates the minimum insertion length of the pen.


VERSION CE 1.1 EN

7

Easy start up: 1. Battery Power. Press button on the left side of the battery to switch battery On/Off (1). A green light indicates the battery is turned On. Pressing the button on top of the battery will indicate the battery status (2).

2. Power On/Off. Press and hold (C) button on display unit for 2 seconds to turn the display on. Display will light up.

3. Bicycle light. To turn On/Off bicycle lights, press and hold (S+) button for 2 seconds.

4. Throttle. To activate 6 km/h auto drive, press the throttle on the left side of the steering wheel. Caution: Auto drive will start immediately! Brake to turn off.

5. Electric Power Support. The bike has 5 electric power support stands, running from low (1) to high (5). This can be read on the display on the left side. Short press (S+) to increase or (S-) to decrease value.

6. More options. By pressing (C) button, you can toggle between the different modes. Battery status (CUR), total milage (ODO), Tripstand (TRIP), digitale Voltage (VOLT)**, digitale meter (CURRENT), counter n.a. (RM) and operating time (TIME)

5. Pedal forward during gear changes and do not use excessive force. 6. Make sure the battery is charged. Partially charged battery can be used, but keep in mind the distance you want

to ride. 7. The bike use PAS (pedal assist) with a rotation sensor. This mean the support will start when you use the pedals.

Additionally, the throttle can be used for direct support from the electric motor. 8. The electric power support will stop when you use the brake levers, stop pedaling or stop using the throttle when

used. 9. Local traffic regulations need to be followed at all times.

1....

2.


VERSION CE 1.1 EN

8

How to fold the Bike:

1. Remove key and release bicycle stand. The pedals can be fold by pulling the ring towards you with your fingers and fold upwards. Face left pedal to front to ease fold.

2. Unlock steer handle by moving the safety ring aside. Pull down lever to release and gently pulling the steer handle downwards. You can remove the steer by unlocking the upper lever and pull the steer out of the shaft. This will reduce the folding size.

3. To fold the E-bike, release safety bracket first by moving it upwards. Pull lever towards you to unlock. The E-bike is ready to be fold. (Important notice: Do not use excessive force)

4. Stand left of the bike and fold the front wheel towards the rear wheel. Both wheels should stand aside. A triangular support is located beneath the pedal bracket. You can rest the bike on this support. It is advisable to cover the bike with some protection during transport to minimize damage to the parts and paint.

5. Securing folded bike Secure the bike front and back wheel with the supplied Velcro.


VERSION CE 1.1 EN

9

Charging/removing battery: Warning: Avoid damage from short circuit between the positive and negative poles of the charger and battery. Do not open charger to avoid damage and injury. Keep in mind that the charger can be warm during charging. Place the charger on a surface that can withstand

heat. Do not cover the charger so it can cool down. Do not place inflammable or explosive goods in the vicinity of the charger to prevent danger.

Store the charger and battery on a safe place out of reach from children. Do not expose the charger and battery in direct sunlight. Store the battery and charger on a cool place. 1. The supplied charger operates with 110/230V. The switch-plug can be connected to the power socket. The E-bike has 1 battery connection point located at the back of the battery (charging features: 36V and 1.8AH) Charging time depends on battery capacity: 17 AH : Approx. 8/9 Hours 11.6 AH: Approx. 6/7 Hours

TIP:

First connect the charger with the bike before connecting to the power socket.

Batteries are made of Lithium, they can be recharged after every use.

The charger stop charging when the battery is fully charged. You can disconnect the charger.

Keep the battery dry and frost-free.

When you are not planning to use the battery for a longer period, store the battery separate from the E-Bike fully charged.

It is advisable to fully deplete the battery the first 3 times and after every 100 charge cycles and do a full charge.

The distance (maximum range) of one battery depends on weather/road conditions, weight of the driver, tire tension, power setting, frequent braking/accelerating and battery condition.

The battery charge according a curve. The first few hours it will charge the most energy. Above 90% it will charge significantly slower.

Red light indicate charging. Green light indicate fully charged.

2. The battery can be removed by turning the key on the left side of the battery. Remove key and pull the battery out of the battery case. Lock the battery when you place it back.


VERSION CE 1.1 EN

10

General information about the E-Bike: 1. The E-Bike is mechanically the same as a normal bike. All moving parts, like cables, brakes, gear and axes can be maintained by using silicon or telfonspray. Check on a regular basis if all bolts and screws are secured. Important points are front and back wheel, luggage rack and steering. When closing the large hinge attachment (frame clamp), note that a certain rising back pressure is felt until the dead point is over. If you are in doubt about the proper operation of the hinge clamp, contact us and do not use the bicycle. Tip:

Spray chain and gear after a wet parcours, the chain needs the most lubrication.

You can clean the chain with a cleaning kit, available at any bike shop.

Tire size is 24 inch, available at any bike shop.

Caution with moist, store the bike in a dry environment. Sensitive parts are the display unit and the controller.

Rusting parts can be treated with telfonspray.

Keep the bike clean and dry to limit corrosion.

2. For gear adjustments you can contact our service line or your local bike technician. Many information about Shimano gears is available on the internet.

3. Keep the tires on tension. This improves driving experience and range. We recommend a tire pressure between 3.5-4.0 Bar.

4. Brakes may need to be adjusted after a while. This can easily be done on the brake levers on the steering wheel. For safety reasons, consult a bike technician for gear and brakes adjustments on the wheel side.


VERSION CE 1.1 EN

11

Important notice: Shinga is authorized to recycle waste batteries and to recycle them safely. If you plan to discard your battery because the

battery has reached its lifetime, contact us.

Meaning Warning Symbols Display:

1. Engine failure: Check wiring connection to the motor.

2. Throttle failure:

3. Controller failure:

4. Brake indicator:

5. Minimum Voltage Protection:

When a warning symbol remains on the screen: Contact your Shinga dealer to determine what the problem

is and if it is serious.


VERSION CE 1.1 EN

12

Technical specifications: 1. Size (LxWxH): 1730 x 660 x 1280 mm

2. Folding size (LxWxH): 900 x 440 x 800 mm

3. Frame: aluminium

4. Motor type: without brushes in back wheel

5. Motor voltage: 36 V

6. Motor output: 250 W max

7. Battery type: Lithium Polymer battery (heat resistant cells)

8. Battery specifications: 36 V, 11.6 AH or 17 AH Panasonic

9. Electric power support: 5 settings

10. Gears: 7-gears Shimano

11. Range on one battery: ±60/±80 Km

12. Maximum payload: 140 Kgs

13. Netto weight incl. Battery: 23.5 Kgs

14. Wheel diameter: 24 inch

15. Distance between the rims: 1170 mm

16. Maximum speed: up to 25 km/h (electric supported)

Frame number is located on front fork.

Contact information Shinga BV

SHINGA BV | Molendijk Zuid 23B | 5482 WZ Schijndel | The Netherlands |

Email: [email protected] | Tel.: +31 73 203 2487

KVK : 62140957 | BTW: NL854680950B01


VERSION CE 1.1 EN

13

EU Declaration of Conformity concerning machines

Supplier: Technical documents: Manufacturer:

SHINGA BV VAN DEN OETELAAR (SHINGA BV) ZHEJIANG JSL VEHICLE CO., LTD

MOLENDIJK ZUID 23B MOLENDIJK ZUID 23B B1.NO.609 SOUTH JINXING STREET

5482 WZ SCHIJNDEL 5482 WZ SCHIJNDEL JINHUA, ZHEJIANG , CHINA

Product: electric folding bike

Model: JSL 039Z

Name: Scamper S200 XL

Serial number bike:

……………………………………………………………………………………………………………………………….

Serial number motor:

……………………………………………………………………………………………………………………………

Serialnumber battery:

………………………………………………………………………………………………………………………….

THIS E-BIKE IS MANUFACTURED ACCORDING AND IN APPLIANCE WITH EUROPEAN UNION GUIDELINES AND REGULATIONS

CONCERNING ELECTRIC BIKES WITH A MAXIMUM SPEED OF 25 KM/HOUR AND A MAXIMUM MOTOR OUTPUT OF 250W

THE FOLLOWING “EN” (ISO) STANDARDS APPLY:

EN ISO 12100:2010 ; EN 15194:2009 ; EN 14764:2005 ; EN 349:1993+A1:2008 ; EN 953:1997+A1:2009 ; EN 13857:2008

EU GUIDELINES APPROVAL:

2006/42/EC MACHINERY DIRECTIVE ; 2006/95/EC LOW VOLTAGE DIRECTIVE ; 2004/108/EC ELECTROMAGNETIC

COMPATIBILITY DIRECTIVE

EU CERTIFICATION AGENCY: ENTE CERTIFICAZIONE MACHINE S.R.L., VIA MINCIO 386, 41056 SAVIGNANO, ITALIE ;

NOTIFICATION AGENCY EU-TYPE EXAMINATION NUMBER: 1282

CERTIFICATE NUMBER: 111123/ZJV845

CERTIFICATE DATE: NOVEMBER 2011

Documents

CE ORIGINAL MANUAL SCAMPER S200 XL VERSION CE 1.1 EN€¦ · CE ORIGINAL MANUAL SCAMPER S200 XL VERSION CE 1.1 EN 4 Introduction Thank you for choosing LACROS. This manual is written