CDS CONSULTANTSCDS CONSULTANTS

MANUFACTURERS & SUPPLIERS MANUFACTURERS & SUPPLIERS OF EQUIPMENT WORLDWIDEOF EQUIPMENT WORLDWIDE

HISTORY OF CDSHISTORY OF CDS CDS was established in 1985 with the vision of providing a

comprehensive service which acts as consultancy for consumers seeking specialised machinery as well as anti corrosion products.

In recent years we have diversified into broader aspects of engineering facilitating the growth of the business and increased global opportunities.

We have a wealth of experience and in-depth product knowledge which covers our portfolio comprehensively.

OUR OBJECTIVESOUR OBJECTIVES

• To provide high quality products accompanied with high quality customer service.

• To understand our customers and endeavour to meet their requirements. Through prompt and efficient responses to consumers we hope to sustain competitive advantage.

OUR PORTFOLIOOUR PORTFOLIO

• Abrasive blast cleaning machines• The most complete range with abrasive

capacities from 5 kgs to 400kgs.• We design special purpose machines and

deliver all over the world.

COMPRESSED AIR MACHINESCOMPRESSED AIR MACHINES

• Saturated wet blast machines

• Dust free blasting cleaning

• Selective coating removal

• Full range of capacities available

COMPRESSED AIR MACHINES COMPRESSED AIR MACHINES (CONTINUED)(CONTINUED)

• Sophisticated range of air driven abrasive blast cleaning machines.

• For use with abrasives such as plastic, carbides and calcium carbonates.

AIRLESS MACHINESAIRLESS MACHINES

• Belt Barrel Machine • Dust Arresters – These can be made to

individual specification. All dust arresters comply with the new European safety regulations regarding factory emissions

• We offer a wide range of airless machines to meet your needs.

ABRASIVESABRASIVES• Copper Slag -An expendable synthetic

mineral abrasive which due to fast rates works well for open nozzle blasting, various grades are available.

• Olivine - A natural mineral abrasive ideally suited for cleaning of a brick masonry. A number of grades are available to suit applications.

• Omni - A synthetic mineral abrasive which is ideally suited to applications where a pale coloured abrasive in aesthetically or environmentally more desirable.

• Steel - High carbon steel short and grit are used in closed systems which employ impeller wheels to propel the abrasive. Available in different grades.

• Garnet - A hard, durable, low-dusting natural mineral abrasive which is capable of achieving high coverage rates. Applications include blasting of stainless steel and special alloys.

• Alumina - A very hard synthetic mineral abrasive which is generally used in small blast cabinets. Typically used for cleaning non-ferrous components & stainless steel.

• Vegetable Abrasives - Natural Organic abrasives such as crushed olive stone or dried corn cob have a gentle cleaning action suited to turbine blades or die and mould cleaning.

• Glass Bead - Very versatile material with a large variety of applications including deburring, deflashing, decarbonising, peening and mould and die cleaning.

SEMI AUTOMATIC DUST FREE SHOT SEMI AUTOMATIC DUST FREE SHOT BLASTING MACHINESBLASTING MACHINES

• For large scale concrete floor preparation-completely dust free.

• Floating roof preparation prior to painting.

• The most complete range of sizes, power outputs and power packs.

WIDE RANGE OF SPARESWIDE RANGE OF SPARES

ERVIN AMASTEEL PRODUCTSERVIN AMASTEEL PRODUCTS

• AMASTEEL Shot is actually a sphere-shaped form of steel casting. Born of a process that was developed and patented by John F. Ervin in 1939, shot is manufactured by pouring a molten mixture of premium grade steel scrap and select alloys through a series of water jets.

• On contact with the water, the molten metal is atomised, forming round particles in a controlled range of sizes. These particles then fall into a water tank, are dried, screened by size, quenched and tempered in a unique heat treatment process. This process assures ultimate control over the microstructure and hardness of the product, prior to a final screening.

• AMASTEEL shot has received more quality recognition awards than any other abrasive manufacturer in the world.

ERVIN AMASTEEL PRODUCTS (1) STEEL SHOT DATAERVIN AMASTEEL PRODUCTS (1) STEEL SHOT DATA• The following are condensations of the Society of Automotive Engineers and Steel Founders'

Society of America specifications for cast steel abrasives and include all of the essential features of both specifications. For greater details, request copies of these complete specifications from your Amasteel Representative. SOCIETY OF AUTOMOTIVE ENGINEERS J827 Cast Steel Shot

• Chemical Analysis • Carbon0.85-1.2%Manganese      S-70 - S-1100.35-1.2%     S-1700.50- 1.2%     S-230 and

Larger0.60 - 1.20%Silicon0.40% minimumSulfur0.05% maximumPhosphorous0.05% maximum• Microstructure • The microstructure of cast steel shot shall be uniform martensite tempered to a degree consistent

with the hardness range, with fine well distributed carbides, if any.• Density • The density of cast steel shot shall be not less than 7 gm/cc.• General Appearance • The cast steel shot shall be as nearly spherical as commercially possible and no more than 20% of

the shot particles shall have objectionable defects.• Hardness • Ninety percent of the hardness checks performed on a representative sample shall fall within the

range of 390-510 VPN hardness number (40-50 HRC). (The hardness may be determined by any of the various methods applicable to small sections such as Tukon Tester with VPN indenter, at loads determined to provide a reliable conversion to Rockwell C.) (This is Ervin AMASTEEL 'S' hardness designed for shot and grit

• Mechanical Tests • Several designs of shot testing machines are available commercially for application to routine

procedures See SAE J445 for methods of checking uniformity of shipments of shot or grit to determine relative fatigue life of different types of shot or grit.

ERVIN AMASTEEL PRODUCTS (1) STEEL SHOT (Continued)ERVIN AMASTEEL PRODUCTS (1) STEEL SHOT (Continued)• Ervin AMASTEEL Special Hardness • L hardness - 90% minimum (55-60 HRC) 630 - 730 VPN

H hardness - 90% minimum (60 HRC minimum) 700 VPN minimum. AMASTEEL is also available in other hardness ranges. For these requirements, the hardness of 90 % of the representative sample shall be within a 100 point VPN range (6 point HRC).

• STEEL FOUNDERS'SOCIETY OF AMERICA 20-66 Standard Specification for Cast Steel Abrasives

• Microstructure • The microstructure of the abrasive shall consist of martensite tempered to a degree consistent with the

hardness range The presence of free ferrite or free graphite is unsatisfactory.• Voids • No more than 10% of cast steel abrasive particles shall contain voids as determined at 10X magnification

A void must be greater than 10% of the area of the abrasive particle to be considered harmful.• Shrinkage • No more than 10% of cast steel abrasive particles shall contain shrinkage as deterwined at 10X

magnification A shrinkage area must be greater than 40% of the area of the abrasive particle to be considered harmful.

• Cracks • No more than 15% of cast steel shot particles, and no more than 40% of cast steel grit particles, shall have

cracks as determined at 10X magnification. A crack is a linear discontinuity whose length is greater than 3 times its width and greater than 20% of the diameter

• Particle Shape of Shot • When examined at 4X magnification, no more than 5% of the shot particles will have a length that is in

excess of twice the cross section.

ERVIN AMASTEEL PRODUCTS (2) STEEL GRIT DATAERVIN AMASTEEL PRODUCTS (2) STEEL GRIT DATA • The following are condensations of the Society of Automotive Engineers and Steel Founders' Society of America

specifications for cast steel abrasives and include all of the essential features of both specifications. For greater details, request copies of these complete specifications from your Amasteel Representative.

• SOCIETY OF AUTOMOTIVE ENGINEERS J827 Cast Steel Shot• Chemical Analysis • Carbon0.85-1.2%Manganese      S-70 - S-1100.35-1.2%     S-1700.50- 1.2%     S-230 and Larger0.60 -

1.20%Silicon0.40% minimumSulfur0.05% maximumPhosphorous0.05% maximum• Microstructure • The microstructure of cast steel shot shall be uniform martensite tempered to a degree consistent with the hardness

range, with fine well distributed carbides, if any.• Density • The density of cast steel shot shall be not less than 7 gm/cc.• General Appearance • The cast steel shot shall be as nearly spherical as commercially possible and no more than 20% of the shot

particles shall have objectionable defects.• Hardness • Ninety percent of the hardness checks performed on a representative sample shall fall within the range of 390-510

VPN hardness number (40-50 HRC). (The hardness may be determined by any of the various methods applicable to small sections such as Tukon Tester with VPN indenter, at loads determined to provide a reliable conversion to Rockwell C.) (This is Ervin AMASTEEL 'S' hardness designed for shot and grit

• Mechanical Tests • Several designs of shot testing machines are available commercially for application to routine procedures See SAE

J445 for methods of checking uniformity of shipments of shot or grit to determine relative fatigue life of different types of shot or grit.

• When examined at 4X magnification, no more than 5% of the shot particles will have a length that is in excess of twice the cross section

ERVIN AMASTEEL PRODUCTS (2) STEEL GRIT (Continued)ERVIN AMASTEEL PRODUCTS (2) STEEL GRIT (Continued)

• Ervin AMASTEEL Special Hardness • L hardness - 90% minimum (55-60 HRC) 630 - 730 VPN

H hardness - 90% minimum (60 HRC minimum) 700 VPN minimum. AMASTEEL is also available in other hardness ranges. For these requirements, the hardness of 90 % of the representative sample shall be within a 100 point VPN range (6 point HRC).

• STEEL FOUNDERS'SOCIETY OF AMERICA 20-66 Standard Specification for Cast Steel Abrasives

• Microstructure • The microstructure of the abrasive shall consist of martensite tempered to a degree consistent with

the hardness range The presence of free ferrite or free graphite is unsatisfactory.• Voids • No more than 10% of cast steel abrasive particles shall contain voids as determined at 10X

magnification A void must be greater than 10% of the area of the abrasive particle to be considered harmful.

• Shrinkage • No more than 10% of cast steel abrasive particles shall contain shrinkage as deterwined at 10X

magnification A shrinkage area must be greater than 40% of the area of the abrasive particle to be considered harmful.

• Cracks • No more than 15% of cast steel shot particles, and no more than 40% of cast steel grit particles,

shall have cracks as determined at 10X magnification. A crack is a linear discontinuity whose length is greater than 3 times its width and greater than 20% of the diameter

• Particle Shape of Shot

MEDIUM HIGH PRESSURE ROTARY MEDIUM HIGH PRESSURE ROTARY AND SWIVEL BALL JOINTSAND SWIVEL BALL JOINTS

We offer all types of metal expansion joints including:-

• Metal bellows expansion joints

• Ball joints

• Perma-Pax Slip jointsSLIP JOINTS

• Wire braid flex hose

STRUCTURED CABLESSTRUCTURED CABLES• The types of cables we sell include the following:-

• Full Locked Coil Rope

• Spiral Strand

• Structural Rope

• Norselay

• Stainless Steel Rope & Strand

• The above cables can be supplied with a number of different types of terminals which consist of hot metal & resin filled sockets and swaged components.

(1) WATER TREATMENT(1) WATER TREATMENT• This sand filter ideal for both

municipal and industrial applications including Tertiary, Surface Water, Oil/Emulsion, Pulp & Paper, Mining, Metal Finishing, and others.

• It offers a whole host of benefits consisting of Uninterrupted flow of filtrate, exceptional particulate removal, saving you of space and no costly maintenance requirements

(2) WATER TREATMENT(2) WATER TREATMENT

• The operating filtration systems come in various sizes with specially designed filters

• They give solutions through innovation and utilising advances in technology.

• You can have confidence in these water plants as they will meet your needs efficiently and effectively irrespective of parameters.

AIR COMPRESSORSAIR COMPRESSORS

• Stationary compressor• Portable compressor Generators• Stationary diesel powered

generating sets  • Generators are available both

stationary and portable

AIR COMPRESSORS (Continued)AIR COMPRESSORS (Continued)

• Rotary Screw Compressors

• Turbo Air compressors

TEMPERATURE MEASURING TEMPERATURE MEASURING EQUIPMENTEQUIPMENT

• Temperature sensors

• Digital thermometers

• Temperature & Pressure recorder

• Heavy duty bimetallic thermometers

NEW HORIZONS FOR CDSNEW HORIZONS FOR CDS

• With advances in technology the equipment which is available in today’s environment means higher quality finishes as well increased durability.

• We are continually developing new products which will be of benefit to our customers taking advantage of this technology.

• We realise and appreciate what consumers are looking for, which is why innovation is so important to us at CDS.

We are experts in the engineering field and we

offer a wide range of products which you may

require. CDS is a name you can trust and rely on in

meeting your needs

STAFF @ CDSSTAFF @ CDS• Chris Stevenson – Managing Director

Tel:- 01758 712245E-mail:- cds@cdsconsultants.co.uk

• Steve Boardman – Sales director Tel:- 0161 9288079E-mail:- sb@cdsconsultants.co.uk

• Frances Randall – Office manager Tel:- 01758 712245E-mail:- fr@cdsconsultants.co.uk

• Simon Stevenson – Marketing ManagerTel:- 01758 712380E-mail:- sas@cdsconsultants.co.uk

CONTACT INFORMATIONCONTACT INFORMATION• If you would like more information or

alternatively wish to place an order then please contact us on the following:- Tel: + 44 (0) 1758 712245 Fax:+ 44 (0)1758 712014 Email : info@cdsconsultants.co.uk

• We hope this PowerPoint presentation has been informative and further more we very much look forward to hearing from you in the future