Upload
dangdang
View
219
Download
0
Embed Size (px)
Citation preview
68-1354-01 Rev. A
02 07
POWERLAN
12V
5A
INPUT
21
34
5
6
7
8
1
2
3
4
ExtronIPL T CR48Ethernet ControlInterface Projector
ScreenControl
ProjectorLiftControl
Laptop
TCP/IPNetwork
ExtronCCR-4BLB AAPController Module
Contact closure outputsInputs to control LEDsRequires 12V/0.1A power for LED illuminationPower not required for contact closure only operation
SCREEN
DOWN
SCREEN
UP
PROJ
DOWN
PROJ
UP
Figure 4 — A typical setup for the CCR-4BLB AAP
Extron Electronics, USA1230 South Lewis StreetAnaheim, CA 92805800.633.9876 714.491.1500 FAX 714.491.1517
Extron Electronics, EuropeBeeldschermweg 6C3821 AH Amersfoort, The Netherlands+800.3987.6673 +31.33.453.4040FAX +31.33.453.4050
Extron Electronics, Asia135 Joo Seng Rd. #04-01PM Industrial Bldg., Singapore 368363+800.7339.8766 +65.6383.4400 FAX +65.6383.4664
Extron Electronics, JapanKyodo Building, 16 IchibanchoChiyoda-ku, Tokyo 102-0082Japan+81.3.3511.7655 FAX +81.3.3511.7656www.extron.com
ExtronVSW 2VGA AVGA Switcher
Projector
Sound System
Local Monitor
FRONT PANEL
LOCKOUT
RS-232
PROTECT
CH 1
CH 2
APA 754
AUDIO POWER AMPLIFIER
CLIP
NORM
SIGNAL
ExtronCCR-2BLB AAPController Module
Contact closure outputsRequires 12V/0.1A Power for LED illuminationPower not required for contact closure only operation
VSW 2VGA A
INPUT 1
21
INPUT 2
Laptop
PCLAPTOP
PC
Figure 5— A typical setup for the CCR-2BLB AAP
CCR-4BLB AAP and CCR-2BLB AAPWiring Guide
About the Contact Closure Control PanelsThe Extron CCR-4BLB AAP and CCR-2BLB AAP are double spaced, control module architectural adapter plates (AAPs). As remote modules, these AAPs can control almost any contact closure controllable device such as Extron switchers and projection screens. They fit into all Extron AAP spaces and include options for two (CCR-2BLB) or four (CCR-4BLB) backlit buttons.
Externally powered, backlit buttons indicate system status by lighting high amber when the input is closed or low amber when the input is open. See “Inputs” at right.
N The CCR AAPs must receive power for their illuminating buttons to light, but power is not required for contact closure usage.
Extron’s Button Label Generator software, available for download at www.extron.com, creates customized labels with text or icons that fit into the button keycap.
ConnectorsPower (12V) — The 2-pole connector is for a power connection to the control panel that lights up the buttons to low amber. Buttons light to high amber only when the Input pins are driven low. See “Inputs” at right.
Inputs — Each button has an input pin for controlling button illumination. Driving an input pin low (shorting it to ground) causes the the corresponding button to light high amber. Each input can handle 18V and sink 1.5mA maximum.
Outputs — Each button has corresponding output pins that are normally open (high). When the button is pressed the pins close (go low).
Input 1 2 G 3 4 G
Output1 2 G 3 4 G
Power 12V G
Figure 1 — CCR-4BLB AAP connectors
Input1 2G
Output1 2G
Power 12V G
Figure 2 — CCR-2BLB AAP connectors
In
+5v
1K
Ground
Input Output
Out
Ground
Figure 3 — Schematics for CCR AAP input and ouput