19
CCNA 2 Practice Final Exam Answer V3.1 1. Which statements are true regarding VTY passwords? (Choose two.) VTY passwords must be encrypted. All VTY lines do not need to use the same password. A VTY password is required to establish telnet sessions. The VTY password is set with the command line console 0. The VTY password must be identical with the enable secret password. 2. Refer to the network and routing table entries shown in the graphic. What will happen when a packet destined for network 192.66.7.0 is received by Router A? It will be forwarded through interface S1. It will be forwarded to the default route. It will be directed toward the Internet. It will be discarded. 3.

CCNA 2 Practice Final Exam

Embed Size (px)

Citation preview

Page 1: CCNA 2 Practice Final Exam

CCNA 2 Practice Final Exam Answer V3.1

1. Which statements are true regarding VTY passwords? (Choose two.)

VTY passwords must be encrypted.

All VTY lines do not need to use the same password.

A VTY password is required to establish telnet sessions.

The VTY password is set with the command line console 0.

The VTY password must be identical with the enable secret password.

2.

Refer to the network and routing table entries shown in the graphic. What will happen when

a packet destined for network 192.66.7.0 is received by Router A?

It will be forwarded through interface S1.

It will be forwarded to the default route.

It will be directed toward the Internet.

It will be discarded.

3.

Page 2: CCNA 2 Practice Final Exam

Which command will produce the output shown in the graphic?

show cdp

show cdp neighbors

show cdp neighbors detail

show cdp detail

4.

Router B received an interface configuration change. Suddenly, it transmits a new update.

Which of the following could have triggered this update? (Choose two.)

Router B received a configuration change.

Router A sent a message requesting an update.

Router C came online after Router B sent the RIP update.

Router B received an error message indicating the last update was not received.

5. How many Telnet sessions can take place simultaneously on a router running a standard

edition of the IOS?

Page 3: CCNA 2 Practice Final Exam

4

5

8

10

6. Which of the following WAN connection services typically use synchronous

communications? (Choose two.)

circuit-switched

leased line

packet-switched

Ethernet

analog modem services

7. Which of the following will add a TFTP server as a fallback source for a router to load an

IOS image?

Router# boot system tftp 163.150.9.31 c2500-d-l.120-9

Router# copy run start

Router# boot system tftp c2500-d-l.120-9.bin 163.150.9.31

Router# copy run start

Router# config t

Router(config)# boot system tftp c2500-d-l.120-9.bin 163.150.9.31

Router(config)# exit

Router# copy run start

Router# config t

Router(config)# boot system tftp 163.150.9.31 c2500-d-l.120-9.bin

Router(config)# exit

Router# copy run start

8. What types of messages are sent periodically by devices configured for CDP?

probes

Page 4: CCNA 2 Practice Final Exam

beacons

signals

advertisements

routing updates

unicast

9. An administrator has made routing protocol changes to a router’s configuration. To

ensure that the changes are implemented, the active configuration is saved and the router

is reloaded. After the router has initialized, the output on the screen displays "Would you

like to enter the initial configuration dialog?[yes/no]:" Why did this dialog appear?

There was a POST failure.

The incorrect IOS loaded.

There was an error in the startup configuration file.

The configuration register was set to ignore NVRAM.

10. Which command is used to redirect debug information to a device that is connected

though a Telnet session?

Router# monitor

Router# terminal redirect vty 0

Router# terminal monitor

Router# monitor output vty 0

11. After issuing the show interfaces command, a technician notices the line "Serial1 is

down, line protocol is down" in the output. Which of the following are possible reasons for

this message output? (Choose three.)

There is a mismatch in the encapsulation type on both ends of the link.

A Layer 1 issue exists.

An interface problem exists.

The clockrate was not set during configuration.

Page 5: CCNA 2 Practice Final Exam

There is no usable media for the protocol.

Keepalive messages are not being sent.

12.

Refer to the above graphic. When using RIP as the routing protocol, how would Chicago use

load balancing to route packets to New York? (Choose two.)

by forwarding packets over paths of equal cost

by forwarding packets according to hop count and speed of the link

by determining which interface has the least traffic and sending to it first

by first determining the speed of the links and then cycling packets through the fastest links

first

by cycling packets through interfaces and routes following the same pattern (Router 1, 2, 3)

each time

13. When would the ROM monitor mode be used? (Choose two.)

maintaining routing configuration settings

modifying the IOS image stored in Flash

running a limited IOS feature set

performing the bootstrap process

14. Which two statements are true about route metrics? (Choose two.)

Page 6: CCNA 2 Practice Final Exam

The more factors that make up a metric, the greater the flexibility to tailor network

operations.

The larger the metric number, the better the path.

Routing protocols use metrics to send routing updates to directly connected neighbors.

Bandwidth and delay are static metrics used by RIP v1.

Ticks, delay, and cost are metrics used by routing protocols.

15.

Which of the following are valid static IP routes? (Choose three.)

RouterB(config)# ip route 192.168.5.0 255.255.255.0 S1

RouterC(config)# ip route 192.168.1.0 255.255.255.0 S1

RouterA(config)# ip route 192.168.3.0 255.255.255.0 192.168.2.2

RouterB(config)# ip route 192.168.1.0 255.255.255.0 192.168.2.2

RouterC(config)# ip route 192.168.2.0 255.255.255.0 192.168.4.1

RouterA(config)# ip route 192.168.4.0 255.255.255.0 192.168.2.1

16. Of the eight network users on the Human Resources department LAN, one cannot

connect to the file server. The user’s PC has successfully booted but can not see the

network. What should be checked first?

the PC power cord

the file server

the PC network interface card LEDs

Page 7: CCNA 2 Practice Final Exam

the LAN switch in the wiring closet

the configuration of the router interface attached to the LAN

17. What can be determined from the partial output of the show ip routecommand

displayed below? (Choose two.)

R 200.200.200.0/24 [120/1] via 192.168.10.2, 00:00:14, Serial0/0

C 192.168.10.0/24 is directly connected, Serial0/0

The next update will be in 76 seconds.

The next update will be in 16 seconds.

The administrative distance is 120 and the metric is 1.

The metric is 120 and the administrative distance is 1.

200.200.200.0 is configured on Serial0/0.

192.168.10.2 is configured on Serial0/0.

18. Why is it useful to have an interface description?

A user can telnet to the router using the interface description.

The interface description is a shortcut way to edit the running-config.

The interface description helps identify distant network connections.

The interface will remain inactive until an interface description is applied.

19.

Page 8: CCNA 2 Practice Final Exam

Assume OSPF is being used on all routers. What happens when the link between Router1

and Router2 goes down? (Choose two.)

Updates start broadcasting every 30 seconds.

Updates start broadcasting every 90 seconds.

Link-state advertisements are flooded.

Link-state advertisements are sent only to neighboring routers.

All routers note the change and adjust routes.

All routers ignore the change until the route becomes active again.

20.

Page 9: CCNA 2 Practice Final Exam

The internetwork needs to communicate between the hosts connected to the E0 interface of

the Utah router and hosts connected to the E0 interface of the Idaho router. The hosts

should also have connectivity to the Internet. Which commands must be configured in order

to enable this communication? (Choose three.)

Idaho(config)# ip route 172.31.1.0 255.255.255.0 172.31.2.1

Idaho(config)# ip route 0.0.0.0 0.0.0.0 s0

Idaho(config)# ip route 172.31.2.0 255.255.255.0 172.31.2.2

Utah(config)# ip route 172.31.3.0 255.255.255.0 172.31.2.1

Utah(config)# ip route 172.31.3.0 255.255.255.0 s1

Utah(config)# ip route 0.0.0.0 0.0.0.0 s0

21. Which statement about datagram life is true?

Each router increments the TTL value of the datagram until the maximum hop count of the

routing protocol is reached. The packet is then returned to the source.

The packet is dropped when the router count and the TTL value match. The source is

notified that transmission has failed.

Each router decreases the TTL value by one until it reaches zero. The datagram is then

discarded and a time exceeded for message is sent to the source.

The destination device discards the datagram if the TTL value is zero on arrival. An ICMP

destination unreachable message is sent back to the source.

Page 10: CCNA 2 Practice Final Exam

22.

The following access list has been created to prevent traffic from host 204.204.7.122 from

accessing the 201.100.11.0 network.

access-list 22 deny host 204.204.7.122

access-list 22 permit any

Which group of commands will properly place this access list so that this host is denied

access only to the 201.100.11.0 network?

RouterA(config)# interface s0/0

RouterA(config-if)# ip access-group 22 in

RouterA(config)# interface s0/0

RouterA(config-if)# ip access-group 22 out

RouterA(config)# interface fa0/0

RouterA(config-if)# ip access-group 22 in

RouterB(config)# interface fa0/0

RouterB(config-if)# ip access-group 22 in

RouterB(config)# interface s0/0

RouterB(config-if)# ip access-group 22 in

RouterB(config)# interface fa0/0

RouterB(config-if)# ip access-group 22 out

23. A network administrator can establish a remote session to a host using the

Router> telnet 192.168.1.1 command but is unsuccessful when using the Router> telnet

Page 11: CCNA 2 Practice Final Exam

Boston command to connect to the same interface. Which of the following could be the

problem? (Choose two.)

The ip host table on the router is not configured.

The command telnet Boston was issued from the wrong router prompt.

The routing table is missing.

Domain name services are not available.

24. Which of the following are functions of a router? (Choose three.)

packet switching

extension of network segments

segmentation of local area networks

selection of best path based on a logical addressing

selection of best path based on a physical addressing

25.

The commands shown in the graphic were entered to alter the startup sequence of the

router. On the next reload, which IOS will be loaded?

The router will load c2500-js-l.112-26d.

The router will load c2500-d-l.120-9.

The router will load the IOS from ROM.

The router will boot into ROM monitor mode.

26.

Page 12: CCNA 2 Practice Final Exam

A network administrator trying to deny Telnet traffic from the 192.5.5.0 network to the

201.100.11.0 network entered the commands shown in the graphic. When monitoring the

network, the administrator noticed that Telnet packets were still passing between those

networks. What is the cause?

The router ignored this type of traffic because it required a standard access list to be

configured instead of an extended one.

The wrong port was configured for the ACL so Telnet traffic was still allowed.

The access list has not been assigned to an interface.

The permit ip any any allowed all traffic to pass regardless of the other statements listed

in this ACL.

27.

Refer to the network graphic. A packet needs to travel from Router F to Router A. Which

path would be selected by the RIP routing protocol if the default metrics are used?

F, G, E, D, B, A

F, E, D, C, A

F, E, D, A

F, E, D, B, A

28. Which of the following is the correct flow of routines for a router startup?

load bootstrap, load IOS, apply configuration

Page 13: CCNA 2 Practice Final Exam

load bootstrap, apply configuration, load IOS

load IOS, load bootstrap, apply configuration, check hardware

check hardware, apply configuration, load bootstrap, load IOS

29. In the configuration register value 0×2104, which value represents the boot field

setting?

x

2

1

0

4

30. ACL statements operate in sequential, logical order. If a condition match is true, the

rest of the ACL statements are not checked. If all of the ACL statements are unmatched,

what happens to the packet?

The packets will be placed in a buffer and forwarded when the ACL is removed.

The packets will be sent to the source with an error notification message.

The implicit permit any statement placed at the end of the list will allow the packets to flow

through uninhibited.

The implicit deny any statement placed at the end of the list will cause the packets to be

dropped.

31. Which of the following would cause the "Message Of The Day" banner to appear?

(Choose three.)

telnetting into the router

initiating a debug session

configuring a router for the first time

using the Aux port to check the current configuration

using the console port to check the current configuration

Page 14: CCNA 2 Practice Final Exam

32.

The administrator knows that port E0 on router B connects to a small LAN without any

routers. Which command can be executed on router B to conserve bandwidth on port E0?

no update timers

holdown-timer 96

poison reverse E0

passive-interface E0

no triggered updates

33. When must a router serial interface be configured with the clock ratecommand?

when the interface is functioning as a DTE device

when the interface timers have been cleared

when the connected DTE device is shut down

when the interface is functioning as a DCE device

34. What are the major characteristics of a wide area network? (Choose three.)

connect devices separated by wide geographical areas

includes technologies of FDDI and Ethernet

uses serial connections to access bandwidth

common carriers are needed for connections

Page 15: CCNA 2 Practice Final Exam

type of connection between a router and a switch

35. If the config-register on a router is set to 0×2102, where is the first place the router

will look for boot system commands?

RAM

ROM

Flash

NVRAM

36. Why would an administrator use the Telnet application when troubleshooting a network?

(Choose three.)

It can be used to verify the operation of application layer software between the source and

destination.

Telnet can use the ICMP protocol to verify a hardware connection and network layer

address.

It is the most complete testing mechanism available.

Remote networks may be accessed via a Telnet session for troubleshooting.

Time to Live values are used by Telnet to identify a failure of device between source and

destination.

37.

The network shown in the graphic is using RIP as the routing protocol. Which of the

Page 16: CCNA 2 Practice Final Exam

following are true regarding the network discovery process that will occur for this network?

(Choose three.)

The Palm Beach router will show networks 192.168.7.0 and 192.168.8.0 as directly

connected networks.

All of the routers will have direct knowledge of the exact topology of the entire network.

The Key West router will forward routing table information to the Miami and Palm Beach

routers.

The Miami router will learn about network 192.168.1.0 from the Key West router.

If network 192.168.4.0 becomes unavailable, the Key West router will notify the other

routers of this fact in the next update.

38. Which of the following are characteristics of the Open Shortest Path First (OSPF) routing

protocol? (Choose two.)

functions as a link-state routing protocol

discards packets when the hop count is greater than 15

calculates the shortest path to a destination using the Diffused Update Algorithm (DUAL)

created as a proprietary routing protocol

floods updates as topology changes occur

broadcasts routing updates every 90 seconds or as triggered by topology changes

39. The following line was displayed in the output of the show ip routecommand.

R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0

What is the value of the routing metric?

3

12

20

30

120

Page 17: CCNA 2 Practice Final Exam

40.

Refer to the output from the show ip route command. What can be concluded from the

output of this router command?

A preferred route to the destination has not been set.

There are two equal cost paths to network 1.0.0.0.

Both interfaces are being used equally to route traffic.

A variance must be set to load-balance across multiple paths.

41. Which of the following are true statements about creating and applying access lists?

(Choose three.)

Access list entries should filter in the order from general to specific.

One access list per port per protocol per direction is permitted.

Standard ACLs should be applied closest to the source while extended ACLs should be

applied closest to the destination.

There is an implicit deny at the end of all access lists.

Statements are processed sequentially from top to bottom until a match is found.

The inbound keyword refers to traffic entering the network from the router interface where

the ACL is applied.

42. Which of the following are true regarding the setup configuration mode? (Choose

three.)

To abort the setup mode, use the CTRL+SHIFT+6 keys.

Page 18: CCNA 2 Practice Final Exam

To abort the setup mode, use the CTRL+C keys.

Setup mode allows a complete configuration of the router.

To enter setup mode, use the privileged mode setup command.

A router that does not find a valid IOS during the boot process will start the system

configuration dialog.

A router that does not find a valid configuration file during the boot process will start the

system configuration dialog.

43. Which of the following are necessary for basic network communication to occur between

hosts that will run such applications as Telnet, web browsers, and e-mail? (Choose three.)

TCP/IP must be installed and properly configured on each device.

Multiple subnets must be configured on the router to ensure accurate delivery.

A default gateway must be configured for datagrams to travel outside of the LAN.

The hosts must be directly connected to a switch to travel outside of the LAN.

To ensure accurate delivery, a router must be configured and accessible by hosts on the

network.

44.

Given the above topology, which of the following statements are true? (Choose two.)

If RouterC receives a packet destined for 10.5.183.46, it will be forwarded out interface

Serial 1.

If RouterA receives a packet destined for 192.168.3.146, it will be forwarded out interface

Ethernet 0.

Page 19: CCNA 2 Practice Final Exam

If RouterA receives a packet destined for 10.5.27.15, it will be forwarded out interface

Serial 1.

If RouterB receives a packet destined for 10.5.27.83, it will be forwarded out interface

Serial 0.

If RouterA receives a packet destined for 172.16.55.101, it will be forwarded out interface

Serial 1.

45. Host name resolution allows for the use of an alphanumeric name to identify network

devices. Select the answer that displays the correct configuration syntax for creating a host

name.

Router# ip host Fontana 200.100.50.5

Router(config)# ip host Fontana 200.100.50.5

Router(config-if)# ip host Fontana 200.100.50.5

Router(config)# ip host Fontana 200.100.50.5/24