Upload
lecong
View
216
Download
1
Embed Size (px)
Citation preview
CARGO STORAGE DRAWERS by: Dep’t of the Interior
For
comfort
and
security
in the
great Oz
outdoors
Available
for most
model
4WD’s
Vans
Utes &
Wagons
Nissan GU Patrol
Department of the Interior Established 1975
411 Princes Highway
Carlton NSW 2218
Ph: (02) 9546 7914
Fx: (02) 9546 2469
www.consoles.com.au
Our cargo storage drawers combine the advantages of having the fit and finish of the original equipment with the strength and durability required for off road driving. We can build you a vehicle specific drawer system to our standard design with two drawers side by side under a false floor, or we can build almost any configuration to your specifications.
Nissan GU Patrol fitted with our standard “side by side” two drawer system with a built in fridge slide on the driver’s side.
Nissan GU Patrol custom-made “double stacked” drawer system designed to suit the customer’s fridge.
RA Rodeo / Holden Colorado / Isuzu D-Max Crew Cab open drawer system
Toyota Prado half drawer system (with fridge slide) designed to allow room for one of the third row seats.
A commercial van with a drawer system designed to fit between the wheel arches. The customer specified the height and length.
A commercial van with a drawer system designed so the drawers slide out through the side door opening.
Visit our website www.consoles.com.au for colour photos and detailed information on the drawer system for your vehicle.
Mitsubishi NM – NP – NS – NT Pajero with one large drawer and a wide fridge slide – (also available with two drawers) Toyota Landcruiser 200 Series
Toyota Landcruiser 100 Series with fridge slide
Toyota Landcruiser 75 – 78 – 70 Series Troopcarrier (300mm high) with a lift off table
Toyota Landcruiser 75 – 78 – 70 Series Troopcarrier (wheel arch height)
Toyota Prado 120 Series with lift off table and drawer partitions
Visit our website www.consoles.com.au for photos of other models and for detailed information.
Nissan GU Patrol 300mm high single drawer unit and floor mounted fridge slide
Ford Ranger / Mazda BT50 Crew Cab Toyota Hilux 2005 & on Dual Cab
(Extra Cab similar)
Toyota Landcruiser 76 Series Stationwagon Holden Rodeo RA / Holden Colorado / Isuzu D-Max Crew Cab (Space Cab similar)
Visit our website www.consoles.com.au for photos of other models and for detailed information.
Custom Trayback Two Drawer System
Ford F250, 1999 and on Crew Cab two drawer system fitted with two fridge slides
Nissan Navara D40 Dual Cab, Two drawer system with open drawer fitted on top.
Ford Falcon AU – BA – BF – BG Utility
Holden VU – VY – VZ Utility
Toyota Hi Ace 2005 and on LWB
Visit our website www.consoles.com.au for photos of other models and for detailed information.
Toyota Hi Ace 2005 and on LWB
This photo of a Prado drawer system shows how our drawers are designed to neatly follow the contours of the vehicle. It also shows a “pull out panel” to allow access to the storage space behind the wheel arch. “Pull out panels” also allow access to the removable trim panels (for jack storage etc.)
Photo: Nissan GU Patrol bed extension. Our bed extensions can be built to suit a vehicle with the middle row seats in (folded up) or a longer bed extension can be built to suit a vehicle with the middle row seats removed. Bed extensions can be installed or removed without removing the drawer system. All bed extensions are attached to the front of the drawer system with four removable brackets. They are also attached to the vehicle by utilising two of the middle row seat captive nuts.
Designed individually for each model, neatly following the contours of the vehicle. We have patterns for most vehicles for full and half drawer systems or we can custom build a drawer system to your specifications.
Heavy duty – suitably durable for off road driving.
Constructed from marine bonded plywood reinforced with steel bracing. All components are either screwed and glued, bolted or riveted.
The drawer rollers are rated at 200 kg evenly distributed (each drawer).
Stainless steel, lockable (keyed alike), flush mounted “T” latches.
Designed to keep the red dust out.
Easy to install
Securely anchored – fitted by utilising genuine captive nuts, no holes to drill.
Guaranteed not to rattle.
Finished in an industrial carpet.
Designed to allow enough space to fit a full cargo barrier. (if required)
Half drawer systems available to allow the use of one of the third row (cargo) passenger seats, or for mounting a fridge slide at floor level.
Comes complete with two pull out panels to take advantage of the storage space next to the wheel arches. These pull out panels also allow full access to all the removable panels in the genuine trim (for jack storage etc.)
Efficient use of space – our cargo drawers are designed individually for each model. The drawers are made as wide as possible, the drawer roller assemblies as compact as possible and the space behind the wheel arches is utilised for storage. All aspects of the design have been calculated for the optimum use of space in the cargo area.
Optional built in fridge slide (rated at 100 kg). The fridge slide can be locked in place, providing security for the contents of the drawer underneath.
The fridge slide and the drawer underneath can be locked together. The two combined can be rolled in and out providing a load capacity of 300 kg (evenly distributed).
Optional heavy duty “tie downs”.
Optional drawer partitions.
Optional bed extension.
Optional “lift off ” table – sits on top of an open drawer. Constructed from 19mm food contact grade polyethylene plastic.
3 year warranty
FEATURES
FEATURES (continued)
Built in TWO HALVES that are bolted together. This
makes our drawers easy to install. Also, a single drawer
unit can be fitted next to one cargo seat or a single
drawer unit next to a fridge slide at floor level.
Built in TWO HALVES that are bolted together. This
makes our drawers easy to install. Also a single drawer
unit can be fitted next to one cargo seat or a single
drawer unit next to a fridge slide at floor level.
Optional DRAWER PARTITIONS - they are a
"press fit" and can be placed in any position
inside the drawer. Held in place by Velcro tape.
Optional "LIFT OFF "TABLE - sits on top of an
open drawer. Constructed from 19mm food contact
grade polyethylene plastic.
drawer underneath. Also, the drawer latch can be used to
hold the fridge slide in the open position. This prevents the
slide from rolling shut when the vehicle is parked on uneven
ground. The fridge slide is mounted on two "Thomas
Regout" telescopic runners. Fridge slides can also be used for
easy access to other heavy objects like a tool box or outboard
motor. Each slide comes complete with four eye bolts, four
straps and four nylon buckles to attach the fridge.
A tough strip of carpet is glued onto each side of each
drawer. There is no load on this carpet, it slides on the steel
to prevent the drawers from rattling. This strip of carpet also
prevents a loaded drawer from rolling in or out too fast
when the vehicle is parked on uneven ground.
The back of each
drawerfront and the front of
each carcass is carpet lined.
When the drawers are closed
this carpet creates a tight
seal. This seal keeps the
inside of your drawers
DUST FREE.
Our storage drawers are
SECURELY ANCHORED –
whenever possible fitted by utilising
genuine captive nuts for the cargo
seats, tie downs etc.
The optional “tie downs”
can be fitted in the position
of your choice on the fridge
slide or the false floor.
Our STAINLESS
steel heavy duty
"T" LATCHES combine a handle a
latch and a lock in
one unit. They are
flush mounted and
the "T" shaped
handle folds down
out of harms way.
The locks for both
drawers are keyed
alike.
The OPTIONAL
INTEGRATED
FRIDGE SLIDE (rated at 100 kg)
can be fitted to
the driver's side
the passenger's
side or both
sides. The fridge
slide can be
locked in place,
providing
security for the
This photo shows the
EFFICIENT USE
OF SPACE between
the drawer and the
carcass. At the top is
the fridge slide
runner, in the centre,
the drawer runner
assembly and at the
bottom is a plywood
re-enforcing panel for
the drawer base.
Each drawer has a load capacity of 200 Kg. The combined weight of
these two men is 170 Kg
The fridge slide is rated at 100 Kg. Each drawer is rated at 200 Kg. The fridge
slide and the drawer underneath can be locked together. The two combined have
a load capacity of 300 Kg. The combined weight of these three men is 250 Kg.
Our storage drawers have been designed to be as strong and as light as possible. This is achieved by constructing the drawers from marine bonded plywood then re-enforcing any areas that are highly stressed with steel components. Some parts are glued screwed and braced, other parts are riveted or bolted together. If anyone tries to tell you that steel drawers are stronger than our plywood/steel drawers just show them these photographs !
Photo of the outside of a drawer The drawers run on sealed bearings. The bearings are attached to the drawer using 10mm dia coach bolts. When the drawer is fully open the bearings at the end of the drawer carry the entire load of the drawer and its contents. As shown in the photo, to increase the load capacity we insert 16 gauge steel plates into the plywood drawer sides.
Inside each drawer the coach bolts for the roller bearings are re-enforced with 50mm dia 2.5mm thick washers.
The steel bearings roll on a 50mm x 20mm x 2.5mm rectangular steel tube. The 2.5mm thickness is very important. When the drawer is fully open, two of the bearings line up with the end of this channel. A heavy load in the drawer would cause the top bearing to dent or crush the tube if it was not thick enough.
The drawer bases are constructed from 16 gauge sheet steel for maximum space inside the drawer.
Captive washers are fitted to the top of each half of the false floor (photos show top of false floor). The plywood in the centre of the false floor is 21mm thick. (photo shows bottom of false floor).
Each half of the false floor (one false floor each side unless a fridge slide is fitted) is attached to the drawer carcass using bolts. The nuts for these bolts are fitted onto 40mm wide 3mm thick steel angle brackets. The angle bracket shown doubles as a stop block to prevent the drawer from sliding out of the drawer carcass. This bracket is attached to the drawer carcass with two 6mm bolts and two nyloc nuts. The sturdy construction of the false floor(s) allows you to attach "tie downs" in any position.
CARGO BARRIERS
We are agents for Milford cargo barriers. If required our drawer systems can be built to suit a full height cargo barrier. We recommend fitting full barriers because they are bolted securely to the floor or the wheel arches. Full barriers are more versatile than half barriers, a full barrier can be moved from the rear position (behind the middle row seats) to the front position (behind the front seats). Our drawer systems are easy to remove and re-install and the full barrier can remain in the vehicle with or without the drawer system in place.
WHY BUY OUR DRAWERS?
Visit our website www.consoles.com.au for colour photos and detailed information on the drawer system for your vehicle
STRONGER AND LIGHTER
BEST FIT
BEST FINISH
BEST FEATURES
BEST VALUE FOR MONEY
Photo shows a full Milford barrier fitted to a GU Patrol
MANUFACTURED IN AUSTRALIA
EASIER TO INSTALL AND REMOVE
IF REQUIRED – CUSTOM BUILT TO
YOUR SPECIFICATIONS
SHORTEST LEAD TIME
3 YEAR WARRANTY
FALSE FLOORS
Custom built for each model. Manufactured from marine bonded plywood and finished in a grey marine
grade carpet. The false floor fits to the vehicle without drilling any holes by utilising existing captive
nuts.
Model listing –
Mitsubishi NM-NP-NS-NT Pajero, Nissan GQ Patrol LWB, Nissan GU Patrol, Toyota 100 series,
Kakadu, Lexus & Sahara
NB : Available for other models – Price on application
Toyota Landcruiser 100 Series False Floor
Mitsubishi NM-NP-NS-NT Pajero False Floor
(with optional custom fridge slide)
Nissan GQ Patrol LWB False Floor
Nissan GU Patrol False Floor
CUSTOM FRIDGE SLIDES Manufactured from marine bonded plywood and steel runners, finished in a grey industrial carpet. There
are two types available:
Fridge Specific
Custom built to suit the size of the customers fridge. We have the dimensions for most model fridges.
Fridge Specific and Vehicle Specific
Custom built to suit the customers’ fridge and to suit the captive nuts in the cargo floor of the customers’
vehicle. This fridge slide is designed to be mounted at floor level without drilling holes and to allow
clearance for the fridge to slide without obstruction.
Toyota Landcruiser 100 Series fridge slide
designed to suit Waeco 80 litre fridge.
Department of the Interior Established 409 Princes Highway Telephone (02) 9546 7914 www.consoles.com.au in 1975 Carlton NSW 2218 Facsimile (02) 9546 2469
E-mail [email protected]
also available for most models
centre roof consoles
across screen full facia and shelf roof consoles
“T” shaped roof consoles
rear roof consoles
dashboard pods
floor trays
floor compartments
full length floor consoles
seat consoles
door pockets
map lights, speakers and all accessories for roof consoles
GME CB and UHF radios
Barrett HF radios
Professional fitting service available
Landcruiser 78 & 79 Series floor tray
Discovery 1994 on dashboard pod
Landcruiser 79 Series cab chassis “T” shaped roof console
Nissan GU(ST) Patrol centre roof console
Landcruiser 100 Series centre roof console
Landcruiser 75 – 79 Series cab chassis shelf
Landcruiser 75 – 78 – 70 Series Troopcarrier across screen full facia roof console
Ford F250 – F350 1999 on full length floor console
Seat console, the seat belt holds it in place Mazda B2600 and Ford Courier floor compartment
See 1000’s of photos of consoles and drawers at www.consoles.com.au