Brochure mitutoyo

Popular Items

1

Popular Items

2

Popular Items

3

CALIPERVernier Caliper - Standart Type

EDP No. Part No. Range Graduation Old Code Remaks

MT0000098 530-101 0-150MM 0.05MM -

With Depth Bar

MT0000099 530-102 0-150MM 0.05MM -MT0000107 530-122 0-150MM 0.02MM -MT0000100 530-104 0-150MM(0-6”) 0.05MM -MT0002351 530-125* 0-150MM(0-6”) 0.05MM -MT0000108 530-312 0-150MM(0-6”) 0.02MM -MT0000101 530-108 0-200MM 0.05MM -MT0002392 530-123 0-200MM 0.02MM 560-123MT0000103 530-114 0-200MM(0-8”) 0.05MM 560-114MT0000105 530-118 0-200MM(0-8”) 0.02MM -MT0000102 530-109 0-300MM 0.05MM -MT0002405 530-124 0-300MM 0.02MM 560-124MT0000104 530-115 0-300MM(0-12”) 0.05MM -MT0000106 530-119 0-300MM(0-12”) 0.02MM -MT0000113 530-501 0-600MM 0.05MM -

-MT0000114 530-502 0-1000MM 0.05MM -

* Inch/mm conversion table labeled on the back of the slider

Vernier Caliper with Fine Adjustment


MT0000123 532-119 0-130MM(0-5”) 0.02MM -With Depth Bar

MT0000125 532-121 0-280MM(0-11”) 0.02MM 562-121

Vernier Caliper with Thumb Clamp


MT0000117 531-122 0-150MM(0-6”) 0.05MM 531-107

With Depth BarMT0000115 531-102 0-200MM 0.05MM -

MT0000118 531-108 0-200MM(0-8”) 0.05MM 561-108

MT0000119 531-109 0-300MM(0-12”) 0.05MM -

OD measurement ID measurement

Step measurement Depth measurement

Thumb Clamp

530-101

532-101

531-101

Popular Items

4

CALIPERVernier Caliper with Carbide Jaws


MT0000109 530-320 0-150MM 0.05MM -

With Carbide-tipped jaw for ODMT0000110 530-321 0-200MM 0.05MM -

MT0000111 530-322 0-300MM 0.05MM -

Outside Point Caliper


MT0000146 536-152 0-150MM 0.05MM - Outside Point Vernier Caliper

Vernier Caliper with Nib Style Jaws


MT0000080 160-151 0-450MM(0-8”) 0.02MM - With Nib Style Jaw (Fine Adjustment)

MT0000239 160-131 0-600MM 0.05MM - With Nib Style Jaw

MT0000081 160-153 0-600MM(0-24”) 0.02MM - With Nib Style Jaw (Fine Adjustment)

OD measurement ID measurement

Step measurement Depth measurement

530-320

536-152

160-131

Popular Items

5

CALIPERDial Caliper Gages

Internal Type External Type


MT0000010 209-106 10-35MM 0.025MM 209-101

Internal TypeMT0000014 209-302 10-30MM 0.01MM 209-608

MT0000158 209-303 20-40MM 0.01MM 209-609

MT0002374 209-404 0-20MM 0.01MM 209-601External Type with Ball Contact Point

° MT 0002677 209-602 0-50MM 0.05MM -

Throat depth 80mm° Throat depth 170mm

Dial Caliper

505-671 505-683


MT0003345 505-671 0-150MM 0.02MM - With Depth Bar, Gray CoverMT0000027 505-683 0-150MM 0.02MM 505-601

With Depth Bar, Silver CoverMT0000030 505-685 0-150MM 0.01MM 505-666MT0000028 505-684 0-200MM 0.02MM 505-602MT0000031 505-686 0-200MM 0.01MM 505-667MT0000029 505-673 0-300MM 0.02MM 505-648-50 With Depth Bar, Gray Cover

Point Caliper

573-721 536-121


MT0002278 573-721 0-150MM (0-6”) 0.01MM 573-221-20with Depth Bar

MT0000139 536-121 0-150MM 0.05MM -

Popular Items

6

CALIPERABS Digimatic Caliper Non Data Output

Depth Rod Type 500-195-20


MT0000039 500-195-20 0-100MM (0-4”) 0.01MM 500-135 With Depth RodMT0002981 500-181-20 1-500MM 0.01MM 500-181

With Depth Bar

MT0000040 500-196-20 0-150MM (0-6”) 0.01MM 500-136MT0000467 500-182-20 0-200MM 0.01MM 500-182MT0000041 500-197-20 0-200MM (0-8”) 0.01MM 500-138MT0002721 500-193 0-300MM (0-12”) 0.01MM -MT0002431 500-738-10 0-200MM (0-8”) 0.01MM 500-177-20

ABS Digimatic Caliper with Data Output

Absolute Coolant Proof Caliper

500-501-10

500-171-20


MT0004787 500-150-20 0-100MM 0.01MM 500-150 With Depth RodMT0000042 500-151-20 0-150MM 0.01MM 500-151

With Depth Bar

MT0000045 500-171-20 0-150MM (0-6”) 0.01MM 500-321MT0000043 500-152-20 0-200MM 0.01MM 500-302MT0000046 500-172-20 0-200MM (0-8”) 0.01MM 500-322MT0000044 500-153 0-300MM 0.01MM 500-303MT0000047 500-173 0-300MM (0-12”) 0.01MM 500-323MT0000058 500-500-10 0-450MM 0.01MM 500-500-50

-MT0000059 500-505-10 0.450MM (0-18”) 0.01MM 500-505-50MT0001779 500-501-10 0-600MM 0.01MM 500-501-50MT0000060 500-506-10 0-600MM (0-24”) 0.01MM 500-506-50MT0000061 500-507-10 0-1000MM (0-40”) 0.01MM 500-507


MT0000471 500-752-10 0-150MM (0-6”) 0.01MM 500-672Non Data Output

MT0003073 500-753-10 0-200MM (0-8”) 0.01MM 500-673

MT0002134 500-723-10 0-150MM 0.01MM 500-155-20 Carbide-tipped OD & ID

MT0003655 500-702-10 0-150MM 0.01MM 500-600 Non Data Output

MT0001918 500-724-10 0-200MM 0.01MM 500-157 Carbide-tipped OD & ID

MT0003656 500-703-10 0-200MM 0.01MM 500-623 Non Data Output

MT0004035 500-722-10 0-200MM 0.01MM 500-156-20 Carbide-tipped

MT0004335 500-714-10 0-300MM 0.01MM 500-634 -

MT0003904 500-754-10 0-300MM (0-12”) 0.01MM 500-674 Non Data Output

MT0001833 500-737-10 0-150MM (0-6”) 0.01MM 500-175 Carbide-tipped OD & ID

Popular Items

7

CALIPERAbsolut Solar Caliper


MT0002525 500-444 0-150MM 0.01MM 500-404 With Depth bar

573-642573-146

573-646


MT0000144 536-146 20-150MM 0.05MM - Inside Point Jaw Type

MT0000069 573-646 20-150MM 0.01MM 573-146-20 Point Jaw Type

MT0001881 573-642 10-200MM 0.01MM 573-142-20 Knife-Edge Type


MT0000070 573-651 0-150MM 0.01MM 573-151-20 Absolute Neck Caliper

Inside Caliper

Digimatic Neck Caliper

Blade Type Caliper

536-136


MT0000067 573-634 0-150MM 0.01MM 573-134-20Absolute Blade Caliper

MT0001977 573-734 0-150MM (0-6”) 0.01MM 573-234-20

MT0000141 536-136 0-300MM 0.05MM - Blade Vernier Caliper


MT0003077 573-191-20 0-180MM 0.01MM 573-191-10 Low Force Type

Absolute Low Force Caliper

Popular Items

8

DEPTH GAGESVernier Depth Gages with Fine Adjustment

EDP No. Part No. Range Graduation Remaks

MT0000086 527-101 0-150MM 0.02MM-MT0000087 527-102 0-200MM 0.02MM

MT0000088 527-103 0-300MM 0.02MM

Vernier Depth Gages


MT0000089 527-201 0-150MM 0.05MM

-MT0002455 527-122 0-200MM 0.02MMMT0000090 527-202 0-200MM 0.05MMMT0000091 527-230 0-300MM 0.05MM

Vernier Depth Gages Hook Type


MT0002203 527-401 0-150MM 0.05MM With Hook Type

Vernier Depth Gages with Fine Adjustment


MT0000093 527-302-50 0-200MM 0.05MM 527-302 -

Absolute Digimatic Depth Gages


MT0000304 571-201-20 0-150MM 0.01MM 571-201-10With SPCMT0001720 571-202-20 0-200MM 0.01MM 571-202-10

MT0000305 571-203-20 0-300MM 0.01MM 571-203-10

Popular Items

9

HEIGHT GAGESDigimatic Height Gages Standard Type


MT0002086 192-613-10 0-300MM 0.01MM 192-613-MT0002315 192-614-10 0-600MM 0.01MM 182-614

MT0002087 192-632-10 0-600MM (0-24”) 0.01MM 192-632


MT0002088 192-663-10 0-300MM 0.01MM 192-663

With SPCMT0000641 192-664-10 0-600MM 0.01MM 192-664MT0002402 192-670-10 0-300MM (0-12”) 0.01MM 192-670MT0001668 570-302 0-300MM 0.01MM 570-228

Digimatic Height Gages Multi Function Type

507-302

Vernier Gages with Adjustment Main Scale Digit Counter Type Dial Height Gages


MT0000339 514-102 0-300MM 0.02MM 514-160

With Adjustable Scale

MT0000340 514-103 0-300MM (0-12”) 0.02MM 514-161MT0000037 514-104 0-450MM 0.02MM 514-172MT0000338 514-105 0-450MM (0-18”) 0.02MM -MT0000342 514-107 0-600MM (0-24”) 0.02MM 514-162

* Optional bi-directional probe


MT0000324 192-130 0-300MM 0.01MM 192-106Counter TypeMT0002085 192-131 0-450MM 0.01MM -

MT0000325 192-132 0-600MM 0.01MM 192-104

192-007

192-663-10

Popular Items

10

MICROMETEROutside Micrometer


MT0000719 103-129 0-25MM 0.001MM -

With Ratchet Stop

MT0000726 103-137 0-25MM 0.01MM -MT0000720 103-130 25-50MM 0.001MM -MT0000727 103-138 25-50MM 0.01MM -MT0000728 103-139-10 50-75MM 0.01MM 103-139MT0000729 103-140-10 75-100MM 0.01MM 103-140MT0000730 103-141-10 100-125MM 0.01MM 103-141MT0000731 103-142-10 125-150MM 0.01MM 103-142MT0000732 103-143-10 150-175MM 0.01MM 103-143MT0000733 103-144-10 175-200MM 0.01MM 103-144MT0000734 103-145-10 200-225MM 0.01MM 103-145MT0000735 103-146-10 225-250MM 0.01MM 103-146MT0002488 406-250 0-250MM 0.001MM 406-521-30MT0003759 406-251 25-50MM 0.001MM - Non Rotating Spindle


MT0000758 104-139A 0-100MM 0.01MM 104-139 Interchangeable Anvils 25,50,75 mmMT0000754 104-135A 0-150MM 0.01MM 104-135 Interchangeable Anvils 25,50,75,100 mmMT0000759 104-140A 100-200MM 0.01MM 104-140 Interchangeable Anvils 25,50,75 mmMT0000755 104-136A 150-300MM 0.01MM 104-136 Interchangeable Anvils 25,50,75,100,125 mmMT0000760 104-141A 200-300MM 0.01MM 104-141 Interchangeable Anvils 25,50,75 mmMT0000761 104-142A 300-400MM 0.01MM 104-142 Interchangeable Anvils 25,50,75 mmMT0000762 104-143A 400-500MM 0.01MM 104-143 Interchangeable Anvils 25,50,75 mmMT0000763 104-144A 500-600MM 0.01MM 104-144 Interchangeable Anvils 25,50,75 mmMT0000773 104-161A 50-150MM 0.01MM - Interchangeable Anvils 50,75,100,125 mm

Outside Micrometer Set


MT0000751 103-913-31 0-150MM 0.01MM 103-913-30 103-137, 103-138, 103-139-10, 103-140-10, 103-141-10, 103-142-10

MT0000752 103-914-31 0-300MM 0.01MM 103-914-30 All Micrometers of 103-913-30 and 103-915-30 in One Set

MT0000753 103-915-10 150-300MM 0.01MM 103-915 103-143, 103-144, 103-145, 103-146, 103-147, 103-148

MT0006190 103-904-10 0-6” 0.001” 103-904-01 103-177, 103-178, 103-179, 103-180, 103-181, 103-182

Outside Micrometer


MT0000706 102-301 0-25MM 0.01MM 101-103With Ratchet StopMT0001903 102-302 25-50MM 0.01MM 102-218

MT0000703 102-303 50-75MM 0.01MM 102-236

Digimatic Micrometer with Interchangeable Anvils


MT0000642 340-251-10 0-150MM 0.001MM 340-251 Interchangeable Anvil 0,25,50,75,100,125 mmMT0000647 340-351-10 0-150MM (0-6”) 0.001MM 340-351

Interchangeable Anvil 0,1”,2”,3”,4”,5”MT0000649 340-352-10 150-300MM (6”-12”) 0.001MM 340-352MT0000644 340-252-10 150-300MM 0.001MM 340-215-30 Interchangeable Anvil 150,175,200,250,275

Outside Micrometer with Interchangeable Anvils

Popular Items

11

MICROMETERDigit Counter Micrometer

Digimatic Micrometer with Dust/Water Protection


MT0000820 193-101 0-25MM 0.01MM -

With Ratchet Stop

MT0000830 193-111 0-25MM 0.001MMMT0000821 193-102 25-50MM 0.01MM -MT0000831 193-112 25-50MM 0.001MMMT0000822 193-103 50-75MM 0.01MM -MT0000832 193-113 50-75MM 0.001MMMT0000833 193-114 75-100MM 0.001MM -

Digimatic Micrometer with 2mm/rev Spindle Feed (QuantuMike)

Digimatic Micrometer with SPC Output

Digimatic Micrometer without SPC Output


MT0000846 293-230 0-25MM 0.001MM 293-521-30

With Ratchet Stop SPCMT0000857 293-330 0-25MM (0-1”) 0.001MM 293-721-30MT0000847 293-231 25-50MM 0.001MM 293-522-30MT0000850 293-232 50-75MM 0.001MM 293-523-30MT0000852 293-233 75-100MM 0.001MM 293-524-30


MT0002328 293-240 0-25MM 0.001MM 293-561-30With Ratchet StopMT0000333 293-340 0-25MM (0-1”) 0.001MM 293-761-30

MT0002647 293-241 25-50MM 0.001MM 293-562-30


MT0004814 29-145 0-25MM 0.001MM - Without SPC Data OutputMT0004817 293-140 0-25MM 0.001MM - With SPC Data Output

Disk Micrometer


MT0000625 123-101 0-25MM 0.01MM -With Ratchet Stop

MT0000616 123-102 25-50MM 0.01MM -

Popular Items

12

MICROMETERDisk Micrometer-Non Rotating Spindle Type


MT0000624 169-201 0-25MM 0.01MM - With Ratchet Stop

Digimatic Disk Micrometer


MT0001938 323-250 0-25MM 0.001MM 323-511-30Rotating Spindle

MT0002095 323-251 25-50MM 0.001MM 323-512-30MT0002675 369-250 0-25MM 0.001MM 369-511-30 Non Rotating Spindle

Crimp Height Micrometer


MT0000795 112-401 0-25MM 0.01MM - Vernier Crimp Height

Digimatic Crimp Height Micrometer


MT0000653 342-271 0-25MM 0.001MM 342-411-30 With SPC

Digital Tube Micrometer


MT0000653 342-271 0-25MM 0.001MM 342-411-30 With SPC

Popular Items

13

MICROMETERTube Micrometer Spherical Anvil Type & Cylindrical Anvils Type


MT0000571 115-115 0-25MM 0.01MM - With Spherical AnvilMT0000573 115-215 0-25MM 0.01MM - With Spherical-Spherical Type

Spherical Anvil

Blade Micrometer


MT0000801 122-101 0-25MM 0.01MM - Type AMT0000805 122-111 0-25MM 0.01MM - Type B

Digimatic Blade Micrometer


MT0000880 422-230 0-25MM 0.001MM 422-111-30 Blade Type A, SPC

Point Micrometer


°MT0000790 112-153 0-25MM 0.01MM - Point 15°MT0000794 112-213 0-25MM 0.01MM - Point 30°

° Non crbide tips

Point Micrometer


°MT0000790 112-153 0-25MM 0.01MM - Point 15°MT0000794 112-213 0-25MM 0.01MM - Point 30°

Popular Items

14

MICROMETERSpline Micrometer


MT0000879 331-251 0-25MM 0.001 - Type A

Gear Tooth Micrometer


MT0002096 324-251-10 0-25MM 0.001MM 324-511-30 Digimatic Gear Tooth Micrometer

Dial Snapmeter

• Anvils optional


MT0003045 523-121 0-25MM 0.001MM 523-101 Direct Go/no-Go Judgment

Tubular Inside Micrometer-Single Rod Type


MT0000581 133-143 50-75MM 0.01MM - Tubular Inside Micrometer, Single Rod Type

Tubular Inside Micrometer - Extension Rod Type


MT0000589 137-202 50-300MM 0.01MM 137-102 Extension Rod 13,25,50(2),100mmMT0000590 137-203 50-500MM 0.01MM 137-103 Extension Rod 13,25,50(2),100,200mmMT0000591 137-204 50-1000MM 0.01MM 137-104 Extension Rod 13,25,50(2),100,200(2)mmMT0000592 137-205 50-1500MM 0.01MM 137-105 Extension Rod 13,25,50(2),100,200(3),300(2)mm

Interchangeable Rod Inside Micrometer


MT0000601 141-206 50-300MM 0.01MM 141-106 With 5 Rods

Popular Items

15

MICROMETERDigimatic Inside Micrometer


MT0000698 345-250-10 5-30MM 0.001MM 345-250 Digimatic Inside Micrometer, Caliper Type

Inside Micrometer Caliper Type

145-185 145-187


MT0000693 145-185 5-30MM 0.01MM -Inside Micrometer, Caliper TypeMT0000694 145-186 25-50MM 0.01MM -

MT0000695 145-187 50-75MM 0.01MM -

Can Seam Micrometer

147-103 147-105


MT0000812 147-103 0-13MM 0.01MM - Can Seam Micrometer for Steel CanMT0000814 147-105 0-13MM 0.01MM - Can Seam Micrometer for Aluminum Can

Vernier Depth Micrometer - Interchangeable Rod Type


MT0000888 129-109 0-50MM 0.01MM - With 2 RodsMT0000894 129-116 0-150MM 0.01MM - With 6 Rods

Digimatic Depth Micrometer - Interchangeable Rod Type


MT0000698 345-250-10 5-30MM 0.001MM 345-250 Digimatic Inside Micrometer, Caliper Type

Popular Items

16

HOLTESTThree Point Internal Micrometer

EDP No. Part No. Range Graduation Old Code Remarks

MT0000913 368-162 8-10MM 0.001MM 368-102-10

Individual

MT0000914 368-163 10-12MM 0.001MM 368-103-10MT0000915 368-164 12-16MM 0.005MM 368-104MT0000916 368-165 16-20MM 0.005MM 368-105MT0000917 368-166 20-25MM 0.005MM 368-106MT0002066 268-167 25-30MM 0.005MM 368-107MT0002982 368-168 30-40MM 0.005MM 368-138MT0002197 368-169 40-50MM 0.005MM 368-139MT0001931 368-170 50-63MM 0.005MM 368-140MT0003112 368-171 62-75MM 0.005MM 368-141MT0001744 468-163 10-12MM 0.001MM 468-133MT0001745 468-164 12-16MM 0.001MM 468-134-10MT0002941 468-165 16-20MM 0.001MM 468-135MT0002942 468-166 20-25MM 0.001MM 468-136-10

Holtest Complete-unit Set


MT0000943 368-911 6-12MM 0.001MM 368-901With Extension RodMT0000944 368-912 12-20MM 0.005MM 368-902

MT0000956 368-914 50-100MM 0.005MM 368-954

Holtest (Type II, Complete-Unit Set In Case)


MT0000958 368-991 12-20MM 0.005MM 368-972Complete SetMT0000957 368-992 20-50MM 0.005MM 368-963

MT0002099 368-992 50-100MM 0.005MM 368-964

Digimatic Holtest Set


MT0002760 468-973 20-50MM 0.001MM 468-953-10 Interchangeable-Head Set

Popular Items

17

DIAL INDICATORDial Indicator Lug-Back - Series 1

1040S 1044S 1013S-10

Features:• Spindle is mad of hardened stainless steel• Gears fit tight for dependable accuracy• Face diameter: 41mm


MT0001897 1013S-10 1MM 0.002MM 1013F Lug-BackMT0001727 1040S 3.5MM 0.01MM 1040F Lug-BackMT0000373 1044S 5MM 0.01MM 1044F Lug-Back

Back Plunger Dial Indicator


MT0001859 1960 1MM 0.01MM -Back Plunger

MT0000375 1160 5MM 0.01MM 1158

1160 1960

Dial Indicator Lug-Back-Series 2

2109S-10 2110S-10 2050S 2046S

EDP No. Part No. Range Graduation Old Code Dial Reading

MT0000389 2109S-10 1MM 0.001MM 2109F 0-100-0MT0000391 2110S-10 1M 0.001MM 2110F 0-100(100-0)MT0000394 2113S-10 2MM 0.001MM 2113F 0-100-0MT0000397 2119S-10 5MM 0.001MM 2119F 0-100-0MT0000379 2046S 10MM 0.01MM 2046FE 0-100(100-0)MT0002136 2047S 10MM 0.01MM 2047FE 0-50-0MT0000387 2050S 20MM 0.01MM 2050FE 0-100(100-0)MT0000388 2052S 30MM 0.01MM 2052FE 0-100(100-0)MT0004345 2046SB 10MM 0.01MM - 0-100

Popular Items

18

DIAL INDICATORSDial Indicator - Series 3

3109S-10 3058S-19

Dial Indicator - Series 4


MT0002445 4046S 10MM 0.01MM 4046 Lug-Back

Dial Test IndicatorPocket Type

Basic Unit

Full Set

Horizontal Type Vertical Type Horizontal Type

513-501, L=12mm513-517, L=20.9mm513-515, L=44.5mm

513-444, L=20.9mm 513-454, L=20.9mm 513-401, L=12.8mm513-405, L=14.7mm513-414, L=36.8mm513-404, L=20.9mm513-415, L=44.5mm


MT0002094 3109S-10 1MM 0.001MM 3109F

Lug-BackMT0000408 3046S 10MM 0.01MM 3046FMT0002613 3050S 20MM 0.01MM 3050FMT0000412 3058S-19 50MM 0.01MM 3058F


MT0000436 513-401E 0.14MM 0.001MM - Dial Test Indicator Basic-Unit Horizontal TypeMT0000419 513-501T 0.14MM 0.001MM 513-101 Dial Test Indicator Full-Set Pocket TypeMT0000439 513-405E 0.2MM 0.002MM 513-205 Dial Test Indicator Basic-Unit Horizontal TypeMT0002106 513-405T 0.2MM 0.002MM 513-905F Dial Test Indicator Full-Set Horizontal TypeMT0000440 513-414E 0.5MM 0.01MM 513-214E Dial Test Indicator Basic-Unit Horizontal TypeMT0002107 513-414T 0.5MM 0.01MM 513-914F Dial Test Indicator Full-Set Horizontal TypeMT0000423 513-404E 0.8MM 0.01MM 513-204E Dial Test Indicator Basic-Unit Horizontal TypeMT0000438 513-404T 0.8MM 0.01MM 513-904F Dial Test Indicator Full-Set Horizontal TypeMT0000422 513-517E 0.8MM 0.01MM 513-117-1 Dial Test Indicator Basic-Unit Pocket SetMT0000421 513-517T 0.8MM 0.01MM 513-117 Dial Test Indicator Full-Set Pocket TypeMT0000450 513-454T 0.8MM 0.01MM - Dial Test Indicator Full-Set Vertical TypeMT0000442 513-415E 1MM 0.01MM 513-215E Dial Test Indicator Basic-Unit Horizontal TypeMT0000441 513-415T 1MM 0.01MM 513-925F Dial Test Indicator Full-Set Horizontal TypeMT0002189 513-515T 1MM 0.01MM 513-115 Dial Test Indicator Full-Set Pocket TypeMT0003996 513-426E 1.5MM 0.01MM - Dial Test Indicator Basic-Unit Horizontal TypeMT0000446 513-444E 1.6MM 0.01MM - Dial Test Indicator Basic-Unit Horizontal Type 20°MT0000447 513-444T 1.6MM 0.01MM - Dial Test Indicator Full-Set Horizontal Type 20°

Popular Items

19

DIAL INDICATORSIDS Digimatic Indicator


MT0002007 543-681 12MM 0.01MM 543-601 Lug-Back With SPCMT0001993 543-681B 12MM 0.01MM 543-681B

Flat-Back With SPCMT0000468 543-682B 12.7MM(0-5”) 0.01MM -

IDF Digimatic Indicator

Features:• The external power supply• GO/NG justment result is out tolerance• The maximum, minimum or runout can be displayed during measurement• Analog bar indcator has been intergrated


MT0002527 543-554E 50.8MM(2”) 0.001MM 543-525E With Back-Lit LCD Screen

IDC Digimatic Indicator


MT0002656 543-400 12MM 0.01MM 543-270 Lug-BackMT0002773 543-390B 12MM 0.001MM 543-250B Flat-BackMT0002126 543-391 0.5”/12.7M 0.001MM 543-251 Lug-BackMT0002722 543-470B 25MM 0.001M 543-450B Flat-Back

Popular Items

20

BORE GAGE

Bore Gage with Standard Dial Indicator

Bore Gage forSmall Hole

Bore Gage forBlind Holes

Bore Gage forXtra Small Hole

Bore Gage -Short Leg Type


MT0000239 511-711 18-35MM 0.01MM 511-171

With Standard Dial Indicator

MT0000235 511-721 18-35MM 0.001MM 511-167MT0000240 511-712 35-60MM 0.01MM 511-172MT0000236 511-722 35-60MM 0.001MM 511-168MT0000238 511-723 50-150MM 0.001MM 511-170MT0000242 511-713 50-150MM 0.01MM 511-174MT0000243 511-714 100-160MM 0.01MM 511-175MT0000244 511-715 160-250MM 0.01MM 511-176



MT0000250 511-203 10-18.5MM 0.001MM -For Small Hole

MT0000251 511-204 10-1835MM 0.01MM -

Bore Gage for Small Hole


MT0000260 511-411 15-35MM 0.01MM -For Blind Hole

MT0000261 511-412 36-60MM 0.01MM -

Bore Gage for Blind Holes


MT0000295 526-127 10-18MM 0.01MM - For Xtra Small Hole

Bore Gage for Extra Small Hole


MT0002153 511-766 18-35MM 0.01MM 511-461

Short Leg TypeMT0002436 511-771 18-35MM 0.001MM 511-471MT0002910 511-767 35-60MM 0.01MM 511-462MT0000262 511-772 35-60MM 0.001MM 511-472MT0002909 511-768 50-150MM 0.01MM 511-464


Popular Items

21

THICKNESS GAGEDigimatic Thickness Gage

547-321 547-301 547-401


MT0000357 547-301 0-10MM 0.01MM - Type A (Standard Type)MT0002617 547-321 0-10MM 0.01MM - Type B (Deep Throat Type)MT0001775 547-401 0-12MM 0.001MM - For Paper, Film, Wire

Dial Thickness Gage


MT0002937 7327 0-1MM 0.001MM - Type A (Standard Type)MT0000359 7301 0-10MM 0.01MM - Type A (Standard Type)MT0000365 7321 0-10MM 0.01MM - Type B (Deep Throat Type)

7321 7301

Dial Thickness Gage-Pocket


MT0000362 7309 0-10MM 0.01MM - Pocket Type

Popular Items

22

STANDDial Gage Stand

7001 (Serrated Anvil)7002 (Flat Anvil)519-109M

(Transfer Stand)215-151-10

(Granite Comparator Stand)

EDP No. Part No. Description Stem Old Code Remaks

MT0000564 7001-10 Working Height 100MM ф8MM 7001 With Serrated AnvilMT0000565 7002-10 Working Height ф8MM 7002 With Flat AnvilMT0000563 519-109-10 Working Height 300MM ф8MM 519-109M With Serrated AnvilMT0000561 215-151-10 150 x 200 x 50MM (H:260MM) ф8MM 215-151 With Fine Adjustment

Magnetic Stand

7010S-10 7011S-10 7032 7014 7012-10 7033B

EDP No. Part No. Range Old Code Remaks

MT0000566 7010S-10 ф8MM,ф4.5MM,ф3/8” 7010SN -MT0000567 7011S-10 ф8MM,ф4.5MM,ф3/8” 7011SN With Fine AdjustmentMT0000568 7012-10 ф8MM,ф6MM,ф3/8” 7012 For Dial Test IndicatorMT0000569 7014 ф8MM,ф6MM,ф3/8” - With On-Off SwitchMT0000570 7033B ф8MM,ф3/8” 7019B Mechanical Lock TypeMT0002934 7032 ф8MM 7027-10 Mechanical Lock Type

Micrometer Stand

EDP No. Part No. Range Remarks

MT0000559 156-101-10 Up To 100MM (4”) Adjustable Angle TypeMT0001768 156-102 Up To 300MM (12”) Vertical TypeMT0000560 156-105-10 0-25MM(0-1”), 25-50MM(1”-2”) Fixed Angle Type

156-102 156-101 156-105

Popular Items

23

CALIBRATION TOOLSSetting Rings

EDP No. Part No. Range Remaks

MT0001054 177-125 8MM/±1.5µM

Steel Setting Ring

MT0001055 177-126 10MM/ ±1.5µMMT0001713 177-284 12MM/ ±1.5µMMT0002983 177-177 16MM/ ±1.5µMMT0001061 177-286 20MM/ ±1.5µMMT0001057 177-139 25MM/ ±1.5µMMT0002481 177-288 30MM/ ±1.5µMMT0001058 177-140 35MM/ ±1.5µMMT0001715 177-290 40MM/ ±1.5µMMT0002420 177-146 50MM/ ±1.5µMMT0002634 177-314 62MM/ ±1.5µMMT0005083 177-302 175MM/ ±1.5µM

Optical Paralel Set


MT0000818 157-903 0-25MM 12, 12.12, 12.25, 12.35MM

Caliper Checker


MT0000269 515-555 300MM Length to Check: 20, 50, 100, 150, 200, 250, 300MMMT0000270 515-556-2 600MM Length to Check: 20, 50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600, MM

Gauge Block Set( ) Length for checking accuracy of inside measurement


MT0000273 516-101-10 1MM-25MM Gauge Block Set Steel (10)#1°MT0002109 516-106-10 2.5MM-25MM Gauge Block Set Steel (10)#0°°MT0000275 516-111-10 1MM-50MM Gauge Block Set Steel (16)#0MT0000285 516-938-10 1.0005MM-100MM Gauge Block Set Steel (112)#0MT0005446 516-942-10 1.0005MM-100MM Gauge Block Set Steel (103)#0MT0000292 516-962-10 1.005MM-100MM Gauge Block Set Steel (47)#0MT0000293 516-966-10 1.005MM-60MM Gauge Block Set Steel (32)#0MT0002822 516-996-10 1.001MM-100MM Gauge Block Set Steel (46)#1MT0006325 516-101Z-10 1MM-25MM Gauge Block Set Steel (10)#1MT0006326 516-106Z-10 2.5MM-25MM Gauge Block Set Steel (10)#0MT0006327 516-938Z-10 1.0005MM-100MM Gauge Block Set Steel (112)#0MT0006328 516-942Z-10 1.0005MM-100MM Gauge Block Set Steel (103)#0MT0006329 516-962Z-10 1.005MM-100MM Gauge Block Set Steel (47)#0MT0006330 516-966Z-10 1.005MM-60MM Gauge Block Set Steel (32)#0

° Optical Parallel°° Optical Parallel, Grinding Stone

Steel 112-Block Set

Popular Items

24

CALIBRATION TOOLSDial Gage Tester


MT0001284 170-102-10 0-25MM 0.001MM 170-102M-2 UDT-2 Dial Gage TesterMT0001521 12AAK84 - - 951498 Stand for Dial Bore Gage

* Not including dial indicators * Not including bore gage

Calibration Tester


MT0001310 521-103 0-1MM 0.0002MM Calibration Tester

Black Granite Surface Plate

* Not including stand

EDP No. Part No. Flatness Grade Remaks

MT0003215 517-101C 0.005MM 1 300 x 300 x 100MMMT0000985 517-111C 0.006MM 1 450 x 300 x 100MMMT0000986 517-114C 0.008MM 1 600 x 450 x 100MMMT0000380 517-103C 0.008MM 1 600 x 600 x 130MMMT0002486 517-303C 0.005MM 1 600 x 600 x 130MMMT0000982 517-105C 0.009MM 1 750 x 500 x 130MMMT0000983 517-107C 0.012MM 1 1000 x 750 x 150MMMT0000984 517-109C 0.013MM 1 1000 x 1000 x 150MM

Popular Items

25

MISCELLANEOUSPrecision Square

916-213 916-404 916-102


MT0000541 916-102 100MM x 70MM Beveled-edge TypeMT0000546 916-213 100MM x 70MM Precision SquareMT0000542 916-103 150MM x 100MM Beveled-edge TypeMT0000547 916-214 150MM x 100MM Precision SquareMT0000555 916-404 200MM x 130MM Precision Square With Stand

Steel Rules - Wide RidgidEDP No. Part No. Range Graduation Remaks

MT0000997 182-105 6”/150MM 1/32”,1/64”,1MM,0.5MM

Wide Rigid RuleMT0000999 182-111 150MM 1MM, 0.5MMMT0001000 182-121 12” 1/8”,1/16”,1/32”,1/64”MT0001002 182-131 300MM 1MM, 0.5MMMT0001004 182-165 24”,600MM 1/32”,1/64”,1MM,0.5MM

Steel Rules - Full Flexible RulesEDP No. Part No. Range Graduation Remaks

MT0001006 182-205 6”/150MM 1/32”,1/64”,1MM,0.5MM Full Flexible RuleMT0001923 182-302 6”/150MM 1/16”,1/32”,1/64”,1MM,0.5MM Semi Flexible RuleMT0001007 182-225 12”/300MM 1/32”,1/64”,1MM,0.5MM Full Flexible RuleMT0001009 182-309 40”/1000MM 1/16”,1/32”,1/64”,1MM,0.5MM Semi Flexible Rule

Combination Square set


MT0001014 180-907U 12”/300MM 1/32”,1/64”,1MM,0.5MMWith Blade

MT0001016 180-910U 300MM 1MM,0.5MM

Universal Bevel Protractor


MT0001020 187-901 150MM, 300M 5min. (0°-90°-0°) With 60°, 45°, 30° EdgesMT0001021 187-907 150MM 5min. (0°-90°-0°) With 60°, 45° Edges

Universal Bevel Protractor

960-606 960-706


MT0001933 960-603 200MM x 44MM x 38.2MM-

960-606-

MT0002274 960-703 200MM x 44MM x 200MM 960-706

V-Block

181-902 181-947


MT0000221 181-902 25MM With ClampMT0001836 181-947 50MM Magnetic Type

Popular Items

26

MISCELLANEOUSRadius Gauge


MT0004379 186-110 0.4MM-6MM (18Pairs)90° Arc

MT0000508 186-902 0.5MM-13MM (26 Pairs)MT0000502 186-105 1MM-7MM (34 Pairs)

180° ArcMT0000503 186-106 7.5MM-15MM (32 Pairs)MT0000504 186-107 15.5MM-25MM (30 Pairs)

186-105

186-110

Screw Pitch GageEDP No. Part No. Range Remaks

MT0000475 188-101 4TPI-42TPI (30 Leaves)Withworth

MT0000476 188-102 4TPI-60TPI (28 Leaves)MT0000477 188-111 4TPI-42TPI (30 Leaves) unifiedMT0000481 188-151 4TPI-42TPI, 0.4MM-7MM Metric & UnifiedMT0000480 188-130 0.35MM-6MM (22 Leaves)

MetricMT0000478 188-121 0.4MM-7MM (18 Leaves)MT0000479 188-122 0.4MM-7MM (21 Leaves)

Thickness Gage

EDP No. Part No. Range Old Remaks

MT0000491 184-302S 0.03MM-0.5MM (13 Leaves) 184-302

Long Leaf Type

MT0000490 184-301S 0.05MM-1MM (13 Leaves) 184-301MT0000492 184-303S 0.05MM-1MM (28 Leaves) 184-303MT0000493 184-304S 0.05MM-1MM (20 Leaves) 184-304MT0000496 184-307S 0.03MM-0.5MM (13 Leaves) 184-307MT0000492 184-303S 0.05MM-1MM (28 Leaves) -MT0002127 184-308S 0.05MM-0.8MM (10 Leaves) -

Reticles

EDP No. Part No. Range

MT0000520 183-102ReticleMT0002369 183-104

MT0001790 183-109

Clear Loupe


MT0000530 183-302 10X MagnificationDrawtube Removable

MT0000531 183-303 15X Magnification

Zoom Loupe


MT0000519 183-101 8X MagnificationOptional Reticle Available

MT0000525 183-131 10X MagnificationMT0001540 950757 - Optional Illuminator


MT0002786 183-304 8X-16X(Zoom) Magnification With Reticle

* Scale Grauation 0.1MM,0.005”

Zoom Loupe Pocket Comparator


MT0000526 183-210 25X Magnification Pen TypeMT0000528 183-203 50X Magnification With Stand


MT0000076 950-223 8”/200MM Outside Spring CaliperMT0000009 950-233 8”/200MM Inside Spring Caliper

Pocket Comparator

Popular Items

27

SURFTESTSurftest SJ-210

Model SJ-210

Code No. 178-561-02EOrder No. MT0002378Evaluation Length 17.5mmMeasuring Range 360µm (-200µM to + 160µM)Measuring Force 0.75mN or 4mN

Drive/Detector UnitDetecting method: SkiddedMaterial of Stylus: Diamond

Stylus tip Radius: 5µm

Evalution ParameterRa,Rc,RY,RZ,Rq,Rt,Tmax,Rp,Rv,R3z,Rsk,Rku,Rc,Rpc,Rsm,Rz1max,S,HSC,RzJIS,Rppi, R∆a,R∆q,Rlr,Rmr, Rmr(c),R∂C,Rk,Rpk,Rvk,Mr1,Mr2,A1,A2,

Vo, Rpm,Tp,Htp,R,Rx,ArRoughness Standard JIS’82, JIS’94, JIS’01, ISO’97,ANSI, VDA

Cutoff Length λc:0.08, 0.25, 0.8, 0.25mmλs: 2.5, 8µM

Display LCD

Data Output Via RS232C Interface/SPC output, USB Digimatic Output

Dimension 115 x 65.8 x 160mm

Model SJ-210

Code No. 178-571-02EOrder No. MT0001807Evaluation Length 17.5mmMeasuring Range 360µm (-200µM to + 160µM)Measuring Force 0.75mN or 4mN

Drive/Detector UnitDetecting method: SkiddedMaterial of Stylus: Diamond

Stylus tip Radius: 5µm

Evalution ParameterRa,Rc,RY,RZ,Rq,Rt,Tmax,Rp,Rv,R3z,Rsk,Rku,Rc,Rpc,Rsm,Rz1max,S,HSC,RzJIS,Rppi, R∆a,R∆q,Rlr,Rmr, Rmr(c),R∂C,Rk,Rpk,Rvk,Mr1,Mr2,A1,A2

,Vo,Rpm,Tp,Htp,R,Rx,ArRoughness Standard JIS’82, JIS’94, JIS’01, ISO’97,ANSI, VDA

Cutoff Length λc:0.08, 0.25, 0.8, 0.25mmλs: 2.5, 8µM

Display LCD (touch Panel

Data Output Via RS232C Interface/SPC output, USB Digimatic Output

Dimension 275 x 109 x 198mm

Surftest SJ-310

Popular Items

28

Popular Items

29

Popular Items

30

Popular Items

31

Popular Items

32

kls/

p&a.

0.28

/2k/

mt.1

4/ca

n.un

i/04

.13

Documents

Brochure mitutoyo