BMW E60/61/90 SPECIFICATION

-. MODEL: QVL-BMW-STD-V2

-. Product Code : BM-0806-101

INDEX

-. Updated points on this version. Updated points on this version-. Precaution-. Main Spec.-. System Compositiony p-. Outline Dimension-. External Appearance -. Connector Pin Assignment-. DIP Switch Setting-. How to use OSD Keypad-. OSD (On Screen Display) -. FMTX Frequency Setting-. How to use parking guide line-. CAN Wiring

P d t C iti-. Product Composition-. FAQ

Updated points on this versionp p

FMTX M d l i dd d i th d t (N d dditi l FMTX- FMTX Module is added in the product. (No need additional FMTX

Module for Audio)

Offering OSD Key Pad- Offering OSD Key Pad

(The remote control is not offered anymore)

- Possible to move the displayed position of Navi (Only on RGB mode)- Possible to move the displayed position of Navi (Only on RGB mode)

- Changed OSD MENU

Precaution- You must keep the car key taken off from the car while you work

this and finally, connect power of the interface.

- When to connect the interface cable, you must keep the power cable taken off.

- You must work this at the environment without any static electricity or damages.

- All of process on this installation should be done by professionals.

- You must not break the labels attached on the board, if it’s broken, no warranty.

- When you receive this package you have to check whether there’s t t i l d d d h t t t i htany parts not included and you have to contact us right away.

- Our repair service do not accept any problems caused by user’s f lt lany fault or carelessness.

Main Spec.1. Input Spec. (MULTI VIDEO INTERFACE)

-. 1 x Analog R,G,B (Sync on Green)

p

-. 1 x CVBS(REAR CAMERA) Input. (Rear camera source)- 3 x A/V (NTST & PAL) Input. -. 1 x LCD Input (Car system Input)

2. Output Spec.-. 2 X CVBS OUTPUT (Video Out for installing Headrest monitor)-. 1 x Audio OUTPUT-. 1 X LCD OUTPUT(LCD Operation)

3. Electric Power Consumption- Input Power : 8VDC ~ 24VDC - Consumption Power : 12WATT, Max

4. Switching Mode (AV source)- Possible to skip AV source while switching Mode (AV source) by DIP S/W

(Refer to the DIP S/W page)- By ‘SET’ button of the OSD Keypad- By Toggle Switch (Option)- By ‘Menu’ button of the car through CAN

System Compositiony pOSD keypad

Switch for source toggle (option)

OEM N i B (C I f )

NAVIGATION Input(Analog RGB)

MCU

OEM Navi Button (Can Interface)

DISPLAYA/V 1

( g )

A/V 2 VIDEO

Car installation OEM LCD

CVBS In(Rear camera)

A/V 3VIDEO

CIRCUITVIDEO MUX

(CAR MAIN BOARD)Car Screen Input POWER

CIRCUITA/V OUT

HEADRESTMONITOR

FMTX

Power Input(+8VDC ~ +24VDC)

Dip S/W

MONITOR (Video out 2

Audio L, R1)

(+8VDC ~ +24VDC)

Outline Dimension147mm * 92mm * 20mm

147mm

92mm

20mm

※ This can change under manufacturer's circumstance

20mm

External AppearanceppLED LCD-OUT CAN I/FMODE LCD-IN

※ This can change under manufacturer's circumstanceKEY PAD RGB (IN) A/V(IN/OUT) POWER DIP S/W

External Appearancepp

RGB(IN)DIP S/W A/V(IN/OUT) POWERKEY PAD

LCD-IN LEDMODELCD-OUTCAN I/F

※ This can change under manufacturer's circumstance

Connector Pin Assignmentg

*RGB-IN Connect *Power Connect

⑥⑤

④

① ② ③ ④ ⑤ ⑥ ⑦

⑥ ④

① R DATA (Red)

② G DATA (Green)

③ B DATA (Blue)① G ( )

③②

①

④ SYNC (White)

⑤ GND (Black)

⑥ NAVI IR (White)

① GND (Black)② I-Drive (Orange)③ FMTX Antenna (Blue)④ N.C⑤ ACC (Red)

⑦ DVD IR (Black)

※ This can change under manufacturer's circumstance

⑤ ( )⑥ REAR (Grey)

Connector Pin Assignmentg

*CAN Connect

① ② ③ ④ ⑤ ⑥

① CAN HIGH – White

② CAN LOW-Yellow

③ N.C

④ N.C

⑤ N.C

⑥ N.C

※ This can change under manufacturer's circumstance

Connector Pin AssignmentConnector Pin Assignment* Power Cable

FILTER & FUSE BOX

FMTXI - DRVGND

990

OrangeBlackGray

Blue

Blue

LAMP RVACC

990mm

RedGrey

Red

Orange

LAMP - RV990mm

GreyBlack

DIP SWDIP SW

#PIN FUNCTION DIP S/W S l ti

※ ON : DOWN, OFF : UP

#PIN FUNCTION DIP S/W Selection

1 RGB INPUT MUTEON : Skipping RGB ModeOFF : RGB Display

ON : Skipping A/V 12 A/V 1 MUTE

ON : Skipping A/V 1OFF : A/V1 Display

3 A/V 2 MUTEON : Skipping A/V 2OFF : A/V2 Display

4 A/V 3 MUTEON : Skipping A/V 3OFF : A/V3 Display

5 To select monitor sizeON : 6.5” LCD Setting (Possible to use BMW 1 series)OFF : 8 8” LCD SettingOFF : 8.8 LCD Setting

6Type of monitor

(Refer to the next page)

ON : Siemens setting (only when to turn on the 5th pin)OFF : Alpine setting (only when to turn on the 5th pin)ON : Operation rear monitor for New 7 (only when to turn off the 5th pin)OFF : 8.8” Setting

7 Rear ModeON : External Rear CameraOFF : OEM Rear Camera

8 N C8 N.C

DIP SWDIP SW 5 6#PIN

Type of monitor

E60 8.8” OFF OFFE60 Alpine 6.5” ON OFF

E60 Siemens 6.5” ON ON

yp

[E60 8.8”]

E60 Siemens 6.5 ON ON

E65 Armrest 6.5” OFF ON

※DIP S/W Use Example ※ S/ Use a p e

[BMW E60-6.5” Alpine]

-. Use Input Mode : A/V3(DVD), Navigation (RGB)

[E60 Alpine 6.5”]

p ( ) g ( )-. Rear Camera : When to be installed on CVBS 4

▷ DIP S/W : 1 OFF▷ DIP S/W : 2,3 ON [E60 Siemens 6.5”]

(INPUT MODE SKIP)▷ DIP S/W : 4 OFF (enable A/V3)▷ DIP S/W : 5 ON (6.5” Alpine)▷ DIP S/W : 6 OFF▷ DIP S/W : 7 ON (enable CVBS4)▷ DIP S/W : 8 OFF [E65 Armrest 6.5”]

How to use OSD Keypadyp

MENU : OSD MENU, Going back to the last step of setting after mode setting

SEL : Select Mode changeSEL : Select, Mode change

UP : Move to Left, Up

DOWN : Move to Right DownDOWN : Move to Right, Down

*FACTORY MODE : Operated with pressing UP->DOWN->UP->MENU keys of the keypad sequently.

OSD(On Screen Display) ( p y)· Analog RGB Mode · Video Mode

COLOR Menu

- BRIGHTNESS

- CONTRAST

- RED, GREEN, BLUE , ,

- HUE

- COLOR BOX

SATURATION - SATURATION

-SHARPNESS

OSD(On Screen Display) ( p y)· Analog RGB Mode · Video Mode

OPTION Menu-OSD H_POS : Move of OSD window to Left, Right

-OSD V_POS : : Move of OSD window to Up, Down

- OSD TRANS : OSD window transparency setting

- SCREEN MODE : Screen Rate setting (4:3, 16:9)

- INITIAL : Initializing OSD setting value

OSD(On Screen Display)( p y)· Factory Mode( INTERFACE SETTING)

-Operated with pressing UP->DOWN->UP->MENU keys of the keypad sequently.

Factory Mode (Interface setting)

- POSITION – H-POSITION : Move of Screen to Left, Right (Only for RGB mode)

- V-POSITION : Move of Screen to Up, Right (Only for RGB mode)

- FMTX : Refer to the FMTX page

OSD(On Screen Display) ( p y)· Factory Mode (INTERFACE SETTING)

Factory Mode (Interface setting)

I DRV T l DVD N i b I DRV (O i l)- I-DRV – To control DVD, Navi by I-DRV (Optional)

- FM-TX – FM-TX USE : FMTX Setting

- FREQUENCY : FMTX Frequency Setting (Refer to the next ‘FMTX frequency setting’ )page)

OSD(On Screen Display) ( p y)· Factory Mode (INTERFACE SETTING)

Factory Mode (Interface setting)

-MODEL - For E60 : When to install on E60 (This is initially set)

F E70 Wh t i t ll E70 (N t il bl t t)- For E70 : When to install on E70 (Not available at present)

-REAR-CAM – By Rear Wire : When to install Back-up Cam by rear wire of power cable (Same with previous version)

- By CAN-BUS : When to install Back-up Cam by CAN wiring. In this case, when the car isy p y g ,in reverse, the CAM is detected automatically.

FMTX Frequency Settingq y gFactory Default : FMTX USE – ON, FREQENCY – 87.5MHz

Get the Factory Mode Operated with pressing UP->DOWN->UP->MENU keys of the keypad sequently

Set “FM-TX USE” to “ON” like the left picture.(‘ON’ is Default). control the frequency by “UP”,( ON is Default). control the frequency by UP , “Down” keys. At the bottom, you can see present frequency and control it from 87.5MHZ to 108MHZ. (1MHZ per each time to press)

※If you do not want this function, should set “FM TX USE” to “OFF”FM-TX USE to OFF

How to use parking guide linep g gFactory Default : DISPLAY - DISABLE

①① When the car is in reverse, if

press ‘UP’ key for 2 sec thepress UP key for 2 sec, the guide line appears on the screen.

②②② If you need to move the line

position, press ‘SEL’ key on the above stepthe above step. (Use ‘Up’, ‘Down’ Key of Keypad)

How to use parking guide linep g g

③ ③ On step no 2 once press “SEL”③ ③ On step no.2, once press SEL key again, you can move the line vertically by “UP”, “Down” keys.

CAN Wiring

Orange+Black:CAN HIGH (White)

Yellow:CAN LOW (Black)

* The color of CAN wires coming from the car can be different by each countries that the car import or any other circumstances.

FAQ1. When can not change mode. -. Check if the Ground Cable (OSD Keypad) is connected or not. - Check if LED is turned on or not If it is not turned on Check if power cable is connected or not-. Check if LED is turned on or not. If it is not turned on, Check if power cable is connected or not.-. Check if CAN is connected well.

2. When the screen is displaying only black color.-. Check if 2nd LED is turned on or not. If it is not turned on, please check all video sources that you

ill t ith th i t f i ti ll twill connect with the interface is operating well or not. -. Check if interface is connected well.

3. When displayed color of screen is not proper. (If it’s too dark or the color is not proper)-. Try to push “Reset button” on the remote control. If the color of screen keeps on displaying wrong y p p p y g g

color, you have to ask manufacturer for the problem.-. Try to adjust Color, Contrast, Brightness by the remote.

4. When Back-up camera is not displayed on the screen. - Turn Dip S/W no 7 on. Turn Dip S/W no.7 on.

5. When the mode you set is not skip. -. Check if Dip S/W is set in proper way.

6 Wh M i th i t di l d6. When Main screen on the car is not displayed. -. Check if In/Out cables are connected well. If it keeps showing the same problem, you have to

ask manufacturer for the problem.

7. When the screen is displaying only white color.-. Check if out cable is connected well. If it keeps showing the same problem, you have to ask

manufacturer for the problem.