Upload
others
View
129
Download
1
Embed Size (px)
Citation preview
Sliding door systems
Automatic sliding door systems
GEZE ECdrive T2
7
GEZE ECdrive T2
Automatic linear sliding door system for doors up to 140 kg leaf weight
The ECdrive T2 linear sliding door system is suitable for a large number of motion cycles and is uncompromisingly reliable. High-quality materi-als guarantee high performance at an excellent price-performance ratio. With a new cover height of 100 mm, this door system meets the high-est design requirements. The optionally available double roller carriage can move leaf weights up to 140 kg in conjunction with the GCprofile Therm profile system. The pre-drilled track and pre-machined elongated holes reduce the installation effort.
Product features ECdrive T2 ECdrive T2-FRFor 1-leaf door systems ● ●For 2-leaf door systems ● ●Height 100 mmDepth 190 mmLeaf weight (max.) 1-leaf 120 / 140 kg*Leaf weight (max.) 1-leaf with GCprofile Therm 140 kg*Leaf weight (max.) 2-leaf 120 / 140 kg*Leaf weight (max.) 2-leaf with GCprofile Therm 140 kg*Opening width 1-leaf 700 to 3000 mmOpening width 1-leaf with GCprofile Therm 700 to 1500 mmOpening width 2-leaf 900 to 3000 mmOpening width 2-leaf with GCprofile Therm 900 to 3000 mmTemperature range -15 to 50 °CIP rating IP20Disconnection from mains Main switch in the driveOpening speed (max.) 0.8 m/sClosing speed (max.) 0.8 m/sHold-open time 0 to 60 sAdjustable opening and closing force (max.) 150 NAutomatic adaptation to traffic flow ● ●Automatic reversal when an obstacle is detected ● ●Pharmacy opening ● ●Interlocking door system function ● -Vestibule function ● -Automatic opening in the event of a power failure adjustable standardAutomatic closing in the event of a power failure adjustable not availableFunction in the event of a power failure adjustable for 30 min / 30 cycles openingAutomatic opening in the event of a fault not available standardApprovals DIN 18650
EN 16005DIN EN ISO 13849: Performance
Level D
DIN 18650EN 16005
DIN EN ISO 13849: Performance Level D
AutSchR● = YES- = NOT AVAILABLE* = 120 KG WITH SINGLE ROLLER CARRIAGE (STANDARD), 140 KG WITH DOUBLE ROLLER CARRIAGE (OPTION) AND GCPROFILE THERM
Technical data
8 GEZE AUTOMATIC DOOR SYSTEMS
Automatic sliding door systems
GEZE ECdrive T2
1 = Transformer2 = Lock3 = Roller carriage4 = Control unit5 = Rechargeable battery6 = Motor
Fitting variants
Door fittings ECdrive T2ISO glass fine-framed ●MONO glass fine-framed ●GCprofile Therm, thermally separated profile system fine-framed ●Toughened safety glass clamping profile ●All-glass system (GGS) -Integrated all-glass system (IGG) -Wooden leaf (provided by customer) ●● = YES- = NOT AVAILABLE
Drive components
Technical data ECdrive T2 ECdrive T2-FRTransformer Ring core with protection and main switchVoltage 230 VFrequency 50 – 60 HzCapacity rating 140 WLock Toothed belt locking, electro-magnetic, bi-stableRoller carriage Door leaf adjustment vertical 10 mmDoor leaf adjustment horizontal 15 mmTiling protection StandardSelf-cleaning ● ●Control unit DCU1-NT DCU1-2M-NTWith fault memory ● ●With memory for statistical data ● ●Software update possible ● ●Bus interface optional ● ●Connection for fire alarm system ● ●Power supply for peripherals ● ●Programmable inputs 3 pc.Programmable outputs 2 pc.Rechargeable battery NiCd, 24 V, 700 mAhMotor Gear motor Double gear motorTorque 400 Ncm● = YES
12
3
45
6
Sliding door systems
Automatic sliding door systems
GEZE ECdrive T2
9
Calculation of the drive length AL in mm*
ECdrive T2 ECdrive T2-FR**
Opening width (ÖW) Drive length Opening width (ÖW) Drive length2-leaf 900 - 1000 ÖW + 1100 900 - 1070 ÖW + 1170
1000 - 3000 2 x ÖW + 100 1070 - 3000 2 x ÖW + 1001-leaf left hand slide to open 700 - 3000 2 x ÖW + 75
700 - 800 ÖW + 880800 - 3000 2 x ÖW + 75
1-leaf right hand slide to open 700 - 3000 2 x ÖW + 75
700 - 800 ÖW + 880800 - 3000 2 x ÖW + 75
* Minimum overall length of the complete system with ISO glass profile system** For FR variants (FR-RWS, FR-LL) request drawing!
Note:Opening widths of escape route sliding doors < 1000 mm are only permitted in exceptional cases.A continuous floor guide is recommended for external systems from an opening width of 2000 mm.The minimum opening widths depend on the requirements of building law.
Calculation of leaf and glass dimensions in mm
ISO glass with aluminium secondary closing edge
ISO glass with rubber secondary closing edge
Toughened safety glass
Leaf width 1-leaf ÖW + 40 ÖW + 35 ÖW + 352-leaf ÖW / 2 + 40 ÖW / 2 +35 ÖW / 2 +35
Leaf height 1-leaf / 2-leaf FH = DHGlass width 1-leaf / 2-leaf FB - 41 FB - 36 FB - 26Glass height FH - 90 FH - 90 FH - 85Glass thickness ISO = 22, Mono = 10
Note: max. leaf ratio width to height 1:4
AL
ÖW
GB
GH
DH
AL = Drive lengthDH = Passage heightGB = Glass widthGH = Glass heightÖW = Opening width
10 GEZE AUTOMATIC DOOR SYSTEMS
Automatic sliding door systems
GEZE ECdrive T2
with ISO/MONO glass fitting – without side panelDrawing no. 70518-ep01 / 70518-ep02
22
22 30
76
190
100
31 11
FH DH
Wall installation, angled floor guide, ISO glass
22
190
1131
76 100
30
FH
1712
DH
Wall installation, angled floor guide, ISO glass
22
190
100
11
30
DH
30
603
FH
3176
Wall installation, continuous floor guide, MONO glass
ÖW+1240
12FB = ÖW+40FW = ÖW
(5)
AL
Vrs
eff.
1-leaf, wall installation, aluminium secondary closing edge, angled floor guide, left hand slide to open, MONO glass
DH = Passage heightFH = Leaf heightFW = Travel pathFB = Leaf widthÖW = Opening widthVrs = Drive extension rightALeff. = Effective drive length
3525
(13)
(5) (5)
ALeff.
35 ÖW+2
FW = ÖW/2FB = ÖW/2+352
FB = ÖW/2+35FW= ÖW/2
2-leaf, wall installation, rubber secondary closing edge, angled / adjustable floor guide, with protective leaf, ISO and MONO glass
Sliding door systems
Automatic sliding door systems
GEZE ECdrive T2
11
Drawing no. 70518-ep10
47.822
190
3630
100
STH
20
1712
FHDH
11
147
6031
Girder section installation (thin), adjustable floor guide, ISO glass
TL = LB-32
LB
4040
FW = ÖW/2FB = ÖW/2+402
FB = ÖW/2+40FW = ÖW/2
STB STBÖW+2
5 5AL eff.
Girder section installation, aluminium secondary closing edge, continuous floor guide, ISO and MONO glass
TL = LB-32
BrsBls
44
35
LB5 5
(5) (5)FW = ÖW/2FB = ÖW/2+352FB = ÖW/2+35FW = ÖW/2
5835
STB STB
ÖW+2
AL eff.
Girder section installation, rubber secondary closing edge, angled / adjustable floor guide, with protective leaf, ISO and MONO glass
LB = Clear construction componentsSTB = Side panel widthSTH = Side panel heightFH = Leaf heightFB = Leaf widthFW = Travel pathÖW = Opening widthDH = Passage heightTL = Girder section lengthBls = Fastening leftBrs = Fastening rightALeff. = Effective drive length
with ISO/MONO glass fitting - with side panel - girder section installation
12 GEZE AUTOMATIC DOOR SYSTEMS
Automatic sliding door systems
GEZE ECdrive T2
Drawing no. 70518-ep14
100
190
STH
DH
17
37.9
36
FH
Lintel mounting, adjustabble floor guide
ALeff.
TL = AL-22
STB
Bls
25
Brs
25STB
LB
35
FW= ÖW/2FB = ÖW/2+35
2
FB = ÖW/2+35FW = ÖW/2
ÖW+2 35
(5)
(5)
2-leaf, lintel mounting, rubber secondary closing edge, angled floor guide with protective leaf
with ISO/MONO glass fitting - with side panel - lintel mounting
new
LB = Clear construction componentsSTB = Side panel widthSTH = Side panel heightFH = Leaf heightFB = Leaf widthFW = Travel pathÖW = Opening widthDH = Passage heightBls = Fastening leftBrs = Fastening rightALeff. = Effective drive length
Sliding door systems
Automatic sliding door systems
GEZE ECdrive T2
13
1-leaf, wall installation, plastic secondary closing edge, adjustable angled floor guide, left hand slide to open
FW = Travel pathFB = Leaf widthÖW = Opening widthVrs = Drive extension rightDH = Passage heightFH = Leaf heightALeff = Effective drive length
25 25
35ÖW+4AL eff.
5 5
35
FW=ÖW/2FB=ÖW/2+35
4
FB=ÖW/2+35FW=ÖW/2
Vrs
25ÖW+635
(5)
AL eff.
FB = ÖW+35FW = ÖW 6
2-leaf, wall installation, rubber secondary closing edge, adjustable floor guide with protective leaf
with toughened safety glass clamping fitting – without side panel
Drawing nos. 70518-ep03 / 70518-ep04
DH
7631
190
FH
17
11
100
Wall installation, adjustabble floor guide
new
14 GEZE AUTOMATIC DOOR SYSTEMS
Automatic sliding door systems
GEZE ECdrive T2
with toughened safety glass clamping fitting – with side panel
Drawing no. 70504-ep1217
31
100
DH30
1907
FH=D
H
7
6014
7
47.8
Girder section installation (thin), adjustable floor guide
TL=LB-32
(5) (5)
LB
STB = LB-(ÖW+4)-10 2
STB = LB-(ÖW+4)-10 2
ALeff.
58 37.5
35
FW=ÖW/2FB=ÖW/2+35
4
FB=ÖW/2+35FW=ÖW/2
5837.5
ÖW+4
35
2-leaf, girder section installation, angled floor guide, protective leaf
TL=LB-32
Brs
LB
ÖW+4
35 35
STB = LB-(ÖW+4)-10 2
STB = LB-(ÖW+4)-10 2
(5)
5
Bls
(5)
5
55
ALeff.
FW=ÖW/2FB=ÖW/2+35
4
FB=ÖW/2+35FW=ÖW/2
2-leaf, girder section installation, adjustable floor guide
LB = Clear construction componentsSTB = Side panel widthFH = Leaf heightFB = Leaf widthFW = Travel pathÖW = Opening widthDH = Passage heightTL = Girder section lengthBls = Fastening leftBrs = Fastening rightALeff. = Effective drive length
Sliding door systems
Automatic sliding door systems
GEZE ECdrive T2
15
with GCprofile Therm, thermally separated profile system fine-framed – without side panelDrawing nos. 70518-ep100 / 70518-ep110
FH
DH
100
190
Ø9
12 40
3176
Wall installation, continuous floor guide
DH
100
190
Ø9
FH
12 4031
76
Wall installation, angled floor guide
FBFW= ÖW
50
1-leaf , wall installation
50
FBFW = ÖW/2 FW= ÖW/2
50
FB33
ÖW (5)(5)ALeff.
2-leaf , wall installation
FH = Leaf heightFB = Leaf widthFW = Travel pathÖW = Opening widthDH = Passage heightALeff. = Effective drive length
16 GEZE AUTOMATIC DOOR SYSTEMS
Automatic sliding door systems
GEZE ECdrive T2
with GCprofile Therm, thermally separated profile system fine-framed – with side panel below lintel
Drawing no. 70518-ep103
100
40 DH
32190
( DH
)
Ø9ST
H10
6076
Vertical section side panel
FH
DH10
0
7
40
190
( DH
)
31
32
6076
Vertical section moving leaf
10STB Re
33FW = ÖW/2 FB FW= ÖW/2FB
50
10
50
LBW
STB Li ÖW
Drive length corresponds to clear opening
50
STB Re 10
FW= ÖW/2 FB FW= ÖW/2FB
33
50
52
10LBW
STB Li
ÖW
Drive length larger than clear opening
LBW = Clear construction widthSTB Li = Side panel width leftSTB Re= Side panel width rightFW = Travel pathFB = Leaf widthÖW = Opening widthDH = Passage height
Sliding door systems
Automatic sliding door systems
GEZE ECdrive T2
17
Drawing no. 70518-ep101
LBH
FH =
DH+3
DH10
0
190
40
60
32
min.1
0ma
x.20
145
min.1
0ma
x.20
LBH
32
40
190
100
DH
145
15ST
H
Vertical section moving leaf, continuous floor guide
Vertical section side panel, angled floor guide
STBRe
50
10
LBW
STBLi10
33FW= ÖW/2 FB FW = ÖW/2FB
50
52
ÖW
2-leaf , horizontal section
with ISO/MONO glass fitting - with side panel – intermediate wall installation
LBW = Clear construction widthLBH = Clear construction heightSTH = Side panel heightSTB Li = Side panel width leftSTB Re= Side panel width rightFW = Travel pathFB = Leaf widthFH = Leaf heightÖW = Opening widthDH = Passage height
18 GEZE AUTOMATIC DOOR SYSTEMS
Automatic sliding door systems
GEZE ECdrive T2
with GCprofile Therm thermally separated profile system – with side panel and fanlight
Drawing no. 70518-ep102
FH10
DH10
0
7
190
40
H OL
min.1
0ma
x.20
LBH
32
145
Vertical section moving leaf
32
40
190
100
DH
H OL
min.1
0ma
x.20
LBH
145
15ST
H
Vertical section side panel
10
52
5050
FB FW = ÖW/2FBFW= ÖW/23
3
LBW
10 STB Li STB ReÖW
Horizontal section
HOL = Height fanlightLBW = Clear construction widthLBH = Clear construction heightSTH = Side panel heightSTB Li = Side panel width leftSTB Re= Side panel width rightFW = Travel pathFB = Leaf widthFH = Leaf heightÖW = Opening widthDH = Passage height