ASBESTOS-CONTAINING MATERIALS SURVEY LONGMONT …

ASBESTOS-CONTAINING MATERIALS SURVEY

LONGMONT ARMORY

1512 MAIN STREET LONGMONT, CO

Cardno ATC Project Number 35.09316.0001

Prepared for:

Department of Military and Veterans Affairs Mr. Darrel Hart Project Manager

6848 S. Revere Parkway Centennial, Colorado 80112

Prepared by:

Cardno ATC 8985 E. Nichols Avenue, Suite 350

Centennial, Colorado 80112

October 27, 2014

Cardno ATC 8985 E Nichols Avenue Suite 350 Centennial, CO 80112 Phone +1 303 799 6100 Fax +1 303 799 3441 www.cardno.com

Australia • Belgium • Canada • Ecuador • Germany • Indonesia • Italy • Kenya • New Zealand • Papua New Guinea • Peru • Tanzania • United Arab Emirates • United Kingdom • United States • Operations in 85 countries

October 27, 2014 Department of Military and Veterans Affairs Mr. Darrel Hart Project Manager 6848 S. Revere Parkway Centennial, Colorado 80112 Re: Asbestos-Containing Materials Survey Longmont Armory 1512 Main Street

Longmont, Colorado Cardno ATC Project Number 35.09316.0012

Dear Mr. Hart: Cardno ATC is pleased to submit the attached Asbestos-Containing Materials Survey report for the above-referenced site. This report includes the scope of work, procedures and methodologies, tables, figures, and analytical laboratory results for the survey. Cardno ATC appreciates the opportunity to perform these services for Department of Military and Veterans Affairs (DMVA) and we look forward to working with you in the future. In the meantime if you have questions or comments regarding the information in this report or if we can be of further assistance please do not hesitate to contact the Cardno ATC Centennial, Colorado office at (303) 799-6100. Sincerely, Cardno ATC

Allen Andersen Project Hygienist for Cardno ATC Direct Line +1 303 799 6100 Email: [email protected]

Kari Yenter Project Hygienist for Cardno ATC Direct Line +1 303 799 6100 Email: [email protected]

Asbestos-Containing Materials Survey Longmont Armory

1512 Main Street Longmont, CO

TABLE OF CONTENTS

1.0 PURPOSE AND SCOPE OF SERVICES .................................................................................... 1

2.0 GENERAL SITE CONDITIONS .................................................................................................. 2

3.0 REGULATORY STANDARDS .................................................................................................... 3 3.1 Asbestos Regulations .............................................................................................................. 3

4.0 ASBESTOS-CONTAINING MATERIALS SURVEY ............................................................. 4 4.1 Homogeneous Materials .......................................................................................................... 4 4.2 Hazard Assessment Factors .................................................................................................... 5 4.3 Sampling Strategy ................................................................................................................... 6 4.4 Suspect Asbestos-Containing Material ................................................................................... 7 4.5 Laboratory Analytical Results ................................................................................................ 7

TABLE I ........................................................................................................................................ 9 SUSPECT ACM SAMPLE LOG AND ANALYTICAL RESULTS ..................................................... 9

6.0 CONCLUSIONS ............................................................................................................................ 10

7.0 ASSUMPTIONS AND LIMITATIONS ..................................................................................... 12

APPENDICES

APPENDIX A:

APPENDIX B:

APPENDIX C:

ACM LABORATORY ANALYTICAL RESULTS SITE

DRAWINGS

INSPECTOR AND LABORATORY ACCREDITATIONS



1

1.0 PURPOSE AND SCOPE OF SERVICES

The purpose of this project was to conduct an Asbestos-Containing Materials (ACM) survey to

identify ACM’s that may be present in the Armory Building located at 1512 Main Street,

Longmont, Colorado. Cardno ATC provided the services as outlined below:

Conduct a comprehensive asbestos survey of the identified building, which includes the

following:

1. Coordinated access to the buildings on an agreed upon schedule; 2. Survey the building to locate suspect asbestos-containing materials (ACM’s); 3. Collected representative samples of suspect asbestos containing building materials

following ASTM and EPA procedures; 4. Based on the site walk conducted on September 10, 2014, the building consists of a

single story metal framed building with a slab on grade foundation; 5. All inspectors will be accompanied by the building owner’s representative, unless

otherwise specified; 6. Suspect ACM samples were analyzed by Polarized Light Microscopy (PLM) in

Cardno ATC’s NVLAP/AIHA Accredited Laboratory located in Centennial, CO; 7. Collected all samples in a manner designed to create minimum disturbance. Cardno

ATC repaired any visible damage that was the result of the sampling efforts.



2

2.0 GENERAL SITE CONDITIONS

The building located at the site consisted of the following:

A one story, metal framed building with a slab on grade foundation covered by a corrugated metal

roofing system. Interior finishes include CMU blocks, drywall and joint compound, wall

textures, ceiling tiles, ceramic tile, floor tile, carpet, and wood.



3

3.0 REGULATORY STANDARDS

3.1 Asbestos Regulations

The survey was performed in accordance with Federal, State and local rules for conducting

asbestos surveys to meet Occupational Safety and Health Administration (OSHA), United States

Environmental Protection Agency (EPA) / National Emission Standards for Hazardous Air

Pollutants (NESHAP) and Colorado Department of Public Health (CDPHE) requirements. The

work was also performed in general accordance with OAA Contract ID No. 73667.



4

4.0 ASBESTOS-CONTAINING MATERIALS SURVEY

Cardno ATC representatives, Mr. Allen Andersen and Ms. Kari Yenter, Asbestos Hazard

Emergency Response Act (AHERA) Accredited Asbestos Building Inspector/Management

Planner, State of Colorado Department of Public Health and Environment (CDPHE)

Certification #19194 and #19227, conducted the asbestos survey of the building from October 8-

9, 2014 and October 16, 2014.

The scope of the Asbestos-Containing Materials Survey included all accessible suspect building

materials and finishes of the interior and exterior areas of the building.

The building was visually inspected for the presence of building materials that were suspected to

contain asbestos. Bulk samples of identified suspect ACMs were collected and placed into

individual containers for transport to a National Voluntary Laboratory Accreditation Program

(NVLAP)/American Industrial Hygiene Association (AIHA)-accredited laboratory for analysis.

Materials visibly identified as non-asbestos (fibrous glass, foam rubber, wood, metal, etc.) were not

sampled. The asbestos survey consisted of three basic procedures: 1) conducting a visual inspection

of the structure and identifying functional spaces; 2) identifying homogeneous material areas of

suspect surfacing, thermal system insulation, and miscellaneous materials; and 3) sampling

accessible, friable and non-friable suspect materials.

4.1 Homogeneous Materials

Prior to collecting any samples, homogenous materials were identified and listed to develop a

sampling strategy. A homogeneous material sampling area can be described as one or more areas of

material that are similar in appearance and texture and that have the same installation date and

function. The actual number of samples collected from each homogeneous sampling area was based

upon criteria detailed in the following sections.



5

4.2 Hazard Assessment Factors

From the list of suspect homogeneous materials, a physical assessment was performed for each

material on the list. A physical assessment includes evaluating the condition, assessing the potential

for disturbance, and determining the friability of each material. Friability is a term used to describe

the ease in which a building material inherently lends itself to disturbance. By definition, "friable"

materials are those that can be crumbled or reduced to powder by hand pressure when dry. Each

material on the list was further classified into one of three categories, which have specific sampling

requirements for each category.

Surfacing Materials: Refers to spray-applied or troweled surfaces such as plaster ceilings and walls, fireproofing, textured paints, textured plasters, and spray-applied acoustical surfaces.

Thermal System Insulation: Refers to insulation used to inhibit heat gain or loss on pipes, boilers,

tanks, ducts, and various other building components. Miscellaneous Materials: Refers to friable and non-friable products and materials that do not fit

in any of the above two categories such as resilient floor covering, baseboards, mastics, adhesives, roofing material, caulking, glazing, and siding. This category also contains wallboard and joint compound wall systems and acoustical ceiling tile.

All confirmed ACMs were then assessed by their condition as good (no visible damage or

showing only very limited damage or deterioration), damaged (less than 25% localized damage

or 10% distributed damage), significantly damaged (25% or greater localized damage or 10% or

greater distributed damage) per Title 40 Code of Federal Regulations Part 63.



6

4.3 Sampling Strategy

The asbestos inspection was conducted in general accordance with the AHERA requirements

using a minimum number of samples collected for each homogenous material, which also meets

the sampling requirement found in 29 CFR 1926.1101.

If the analytical results indicated that all the samples collected per homogenous material did not

contain asbestos, then the homogenous material would be considered a non-ACM. However, if the

analytical results of one or more of the samples collected per homogenous material indicate that

asbestos is present in quantities of greater than 1 percent asbestos by calibrated visual estimation (as

defined by EPA), all of the homogenous material would be treated as an ACM regardless of any

other analytical results. Material which can visually be determined to be non-asbestos (i.e., fibrous

glass, foam rubber, metal, etc.) by the accredited inspector are not required to be sampled.

Miscellaneous materials require adequately representative sampling, which is typically done by

collecting from one to three samples per material. Inspectors typically rely on other survey

observations such as the condition, friability, and quantity of material to determine what would be a

sufficient amount of samples to accurately evaluate the presence or absence of asbestos content. For

this survey, one to three samples per each homogenous miscellaneous material were collected.

Actual collection of a bulk asbestos sample involves physically removing a small piece of

material and placing it in a marked, airtight container. Sample containers are marked with a

unique identification number, which is also noted in the field notes.



7

4.4 Suspect Asbestos-Containing Material

Seventy-one (71) samples were collected with one-hundred eighteen (118) sample layers

analyzed. For example, floor tile and associated mastic are collected as one bulk sample but are

analyzed as two distinct materials by the asbestos laboratory, as required by NVLAP.

4.5 Laboratory Analytical Results

Bulk samples were analyzed by Cardno ATC Analytical Laboratory located in Centennial,

Colorado, using PLM according to EPA method 600/R-93/116. This laboratory participates in the

NVLAP, a quality assurance program for PLM, and is accredited by the National Institute of

Standards and Technology (NIST).

Any material that contains greater than 1 percent (>1%) asbestos by PLM is considered an ACM

and must be handled according to OSHA, EPA, and applicable state and local regulations.

For friable materials, when the amount of asbestos in the sample material is reported as “None-

Detected” by PLM analysis, no further verification of the sample results by Point Counting

Methodology is recommended.

For friable materials, when the amount of asbestos in the sample material is reported as “Trace

Asbestos Detected” or less than 10% asbestos by PLM analysis, the client may either assume the

amount to be greater than 1% and treat the material as ACM or require further verification of the

amount by Point Counting Methods. If the result obtained by Point Counting is different from the

result obtained by PLM analysis, the Point Count Method result should be used.

For non-friable materials, when the amount of asbestos in the sample material is reported as greater

than 1% asbestos by PLM analysis, no further verification of the sample results by alternative

methods of identification such as Transmission Electron Microscopy (TEM) Chatfield Method is

recommended.



8

For non-friable materials such as vinyl/asphaltic products (floor tiles/ floor sheeting, mastics,

shingles etc.), where small, thin asbestos fibers may have been potentially milled into the non-

organic binder matrix, when the amount of asbestos in the sample material is reported as “None-

Detected” by PLM analysis, due to the difficulty in analyzing such small, thin asbestos fibers in

resinously bound materials by PLM analysis, EPA recommends but does not require that these

types of materials, which were reported as non-ACMs by PLM, be further analyzed using TEM

Chatfield Method. Cardno ATC did not conduct such analysis.

The results of the laboratory analysis are summarized in tabular form in Section 5.0. The

laboratory analytical report and corresponding chain-of-custody documents are included in

Appendix A. Results are reported in percent asbestos by calibrated visual estimation and

indicate the types of asbestos. Other common non-asbestos components may also be noted on

the analytical reports. A drawing(s) showing bulk sample locations is provided in Appendix B.

Inspector and laboratory accreditations are provided in Appendix C.

Asbestos-Containing Materials Survey Longmont Armory 1512 Main Street

9

TABLE I SUSPECT ACM SAMPLE LOG AND ANALYTICAL RESULTS

Sample No. Material Description Asbestos Content

Material Quantity Condition

1,2,3,61,62,63,64 CMU Block Filler 3% Chrysotile Asbestos

9,000 SF Good

4,5,6,7,8,43,44 Ceiling Tile ND N/A Good 9,10,11 Attic Insulation ND N/A Good

12,13,14,15,65 Window Glazing 3% Chrysotile Asbestos

200 LF Damaged

16,17,18 Carpet Mastic ND N/A Good

19,20,21 12”x12” Floor Tile (white w/brown streaks) and Associated Mastic (black)

5% Chrysotile Asbestos (ND in Mastic)

1500 SF Good

22,23 Drywall/ Joint Compound/ Texture

ND N/A Good

24 Texture ND N/A Good

25,26,27 Drywall/ Joint Compound/ Texture

ND N/A Good

28,29 Texture ND N/A Good

30,31,32 Drywall/ Joint Compound/ Texture

ND N/A Good

33,34 Texture ND N/A Good35,36,37 Texture ND N/A Good

38,39,40,41,42 Cove Base (Tan) and Associated Mastic

ND N/A Good

45,46,47 Ruminant Mastic ND N/A Good48,49,50,51,52,53,54 Drywall/ Joint Compound ND N/A Good

55,56,57 12”x12” Floor Tile (white) and Associated Mastic

ND N/A Good

58,59,60 Ceiling Texture ND N/A Good

66,67,68 Cove Base (Black) and Associated Mastic

ND N/A Good

69,70,71 Lath and Plaster ND N/A Damaged

Previously Sampled Roof Coating 5% Chrysotile Asbestos

14,200 LF Good


10

Sample No. Material Description Asbestos Content

Material Quantity Condition

Previously Sampled Roofing Tar 15% Chrysotile Asbestos

3,000 LF Good

Previously Sampled Exterior Texture on Corrugated Panels

3% Chrysotile Asbestos

4,500 LF Good

6.0 CONCLUSIONS

The results of the asbestos survey conducted in the Armory Building located at 1512 Main

Street, Longmont, Colorado facility building indicate that: three of the suspect building materials

sampled were found to contain more than 1% asbestos. Floor tiles located on the South East and

South West sides of the building contain 5% asbestos, CMU block filler located throughout the

building contains 3% asbestos, and window glazing located throughout the building contains 3%

asbestos. Previous asbestos sampling records indicated that the roof coating contains 5%

asbestos, roofing tar contain 15% asbestos and the yellow/cream textured paint on the exterior of

the building contains 3% asbestos.

Contractors and employees working in these building should be made aware of the possibility

that concealed ACMs may be found during demolition/renovation. They should be advised not

to disturb known or suspect ACMs without owner approval.

Any concealed building materials discovered during maintenance or renovation activities, which

are suspected to contain asbestos, should be sampled and analyzed to confirm the presence of

asbestos prior to disturbing.

* ND refers to Non-Detect for asbestos content in material sample.** N/A refers to Not Applicable


11

The EPA has not prohibited the manufacture and import of miscellaneous materials, such as vinyl

floorings, mastics, roofing materials, etc. As a result, any future replacement materials should be

checked for the presence of asbestos prior to installation.


12

7.0 ASSUMPTIONS AND LIMITATIONS

The results, findings, conclusions, and recommendations expressed in the report are based only

on conditions that were noted during Cardno ATC’s inspection of the Armory Building located

at 1512 Main Street, Longmont, Colorado.

The selection of sample locations and frequency of sampling was based on Cardno ATC’s

observations and the assumption that like materials in the same area are homogeneous in content.

Limited destructive investigation was conducted as needed. Concealed ACMs may exist in

concealed areas not investigated or identified. Under no circumstances is the report to be

utilized as a bidding document or as a project specification document since it does not have

all the components required to serve as an Asbestos Abatement Project Design document

or an Abatement Workplan.

Our professional services have been performed, our findings obtained, and our conclusions prepared

in accordance with customary principles and practices in the fields of environmental science and

engineering. This statement is in lieu of other statements either expressed or implied. This report

does not warrant against future operations or conditions, nor does it warrant against operations or

conditions present of a type or at a location not investigated.


13

APPENDIX A

ACM LABORATORY ANALYTICAL RESULTS

ANALYTICAL REPORT

10/17/2014

0018813Order No.:

Report Date:

Project: Longmont Armory/ 1512 Main Street

Prepared for:

6848 South Revere Parkway Suite 337Englewood, CO 80112

Colorado Department of Military Affairs

8985 E. Nichols Avenue, Suite 350, Centennial, CO 80112 Ph: 303-799-6100Cardno ATC

PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:

6848 South Revere Parkway Suite 337

Englewood CO 80112


Sample Date: 10/09/2014

0018813

ATC Job No.:

Longmont Armory/ 1512 Main StreetProject:

Darrel Hart

10/17/2014Report Date:

NVLAP Lab Code 102031AIHA Lab Code 101536

Customer Project No.:

Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 1 of 14

Customer:

035.09316.0001

8985 E. Nichols Avenue, Suite 350

Phone +1 303 799 6100Centennial, CO 80112

www.cardno.comFax +1 303 799 3441

www.cardnoatc.com

Lab No. Sample Description / LocationClient No. Asbestos Content

Chrysotile1 <1%0018813-001 Block Filler, Lt. Gray/ Off White/ Beige, 23°C

On Drawing

Chrysotile2 2%0018813-002 Block Filler, Lt. Gray/ Off White/ Beige, 23°C

On Drawing

Chrysotile3 <1%0018813-003 Block Filler, Lt. Gray/ Off White/ Beige, 23°C

On Drawing

None Detected4 0018813-004 Ceiling Tile, White/ Beige, 23°C

On Drawing


On Drawing


On Drawing


On Drawing


On Drawing

None Detected9 0018813-009 Insulation, Black, 23°C

On Drawing


On Drawing

These samples were analyzed by layers. Specific layer or component asbestos content is indicated when relevant. The EPA considers a material to be asbestos containing only if it contains more than one percent asbestos by Calibrated Visual Area Estimation (CVAE). EPA regulations also indicate that Regulated Asbestos Containing Materials (RACM) -- materials which are friable or may become friable -- be further analyzed by point counting when the results indicate less than ten percent asbestos by CVAE. Our laboratory utilizes CVAE on a routine basis and does not include point counting unless specifically requested. The results may not be reproduced except in full, and should not be used as a scope of work for abatement without consulting with Cardno ATC.

PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 2 of 14

Customer:

035.09316.0001




www.cardnoatc.com



On Drawing

Chrysotile12 2%0018813-012 Window Glazing, Lt. Gray, 23°C

On Drawing


On Drawing


On Drawing


On Drawing

None Detected16 0018813-016 Carpet Adhesive, Beige, 23°C

On Drawing


On Drawing


On Drawing

Chrysotile19 5%0018813-019 LAYER 1Floor Tile, White, 23°C

On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 3 of 14

Customer:

035.09316.0001




www.cardnoatc.com


None Detected19 0018813-019 LAYER 2Mastic, Black

On Drawing

None Detected20 0018813-020 LAYER 1Floor Tile, White, 23°C

On Drawing

None Detected20 0018813-020 LAYER 2Mastic, Black

On Drawing

Chrysotile21 2%0018813-021 LAYER 1Floor Tile, White, 23°C

On Drawing

None Detected21 0018813-021 LAYER 2Mastic, Black/ Tan

On Drawing

None Detected22 0018813-022 LAYER 1Texture, Off White, 23°CNote: No Joint Compound Present

On Drawing

None Detected22 0018813-022 LAYER 2Drywall, Off White/ Brown

On Drawing

None Detected23 0018813-023 LAYER 1Texture, Off White

On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 4 of 14

Customer:

035.09316.0001




www.cardnoatc.com


None Detected23 0018813-023 LAYER 2Drywall Tape, Beige

On Drawing

None Detected23 0018813-023 LAYER 3Joint Compound, Beige

On Drawing


On Drawing

None Detected24 0018813-024 Texture, Off White, 23°CNote: No Drywall Present

On Drawing

None Detected25 0018813-025 LAYER 1Texture, White, 23°CNote: Sample is mainly Paint - little Texture present

On Drawing


On Drawing


On Drawing


On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 5 of 14

Customer:

035.09316.0001




www.cardnoatc.com


None Detected26 0018813-026 LAYER 1Texture, White

On Drawing


On Drawing


On Drawing


On Drawing

None Detected27 0018813-027 LAYER 1Texture, White

On Drawing


On Drawing


On Drawing


On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 6 of 14

Customer:

035.09316.0001




www.cardnoatc.com


None Detected28 0018813-028 Texture, WhiteNote: No Drywall Present

On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 7 of 14

Customer:

035.09316.0001




www.cardnoatc.com



On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


On Drawing

None Detected33 0018813-033 Texture, White, 23°CNote: Sample is mainly Paint - little Texture present

On Drawing


On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 8 of 14

Customer:

035.09316.0001




www.cardnoatc.com



On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


On Drawing

None Detected38 0018813-038 LAYER 1Cove Base, Brown, 23°C

On Drawing

None Detected38 0018813-038 LAYER 2Cove Base Mastic, Yellow

On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 9 of 14

Customer:

035.09316.0001




www.cardnoatc.com



On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 10 of 14

Customer:

035.09316.0001




www.cardnoatc.com



On Drawing


On Drawing

None Detected45 0018813-045 Mastic, Tan/ Beige, 23°C

On Drawing


On Drawing


On Drawing

None Detected48 0018813-048 LAYER 1Joint Compound, White, 24°C

On Drawing


On Drawing


On Drawing


On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 11 of 14

Customer:

035.09316.0001




www.cardnoatc.com


None Detected50 0018813-050 LAYER 1Joint Compound, White/ Beige, 23°C

On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 12 of 14

Customer:

035.09316.0001




www.cardnoatc.com



On Drawing


On Drawing


On Drawing

None Detected55 0018813-055 LAYER 2Mastic, Yellow

On Drawing


On Drawing


On Drawing


On Drawing


On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 13 of 14

Customer:

035.09316.0001




www.cardnoatc.com


None Detected58 0018813-058 Ceiling Texture, White, 23°C

On Drawing


On Drawing


On Drawing

None Detected61 0018813-061 Block Filler, Lt. Gray/ Off White/ Beige, 23°CNote: Sample is mainly Paint - little Texture present

On Drawing

None Detected62 0018813-062 Block Filler, Lt. Gray/ Off White/ Beige, 23°C

On Drawing


On Drawing


On Drawing

None Detected65 0018813-065 Window Glazing, Lt. Gray, 23°C

On Drawing

None Detected66 0018813-066 LAYER 1Cove Base, Black, 23°C

On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 14 of 14

Customer:

035.09316.0001




www.cardnoatc.com


None Detected66 0018813-066 LAYER 2Cove Base Mastic, Cream

On Drawing


On Drawing


On Drawing


On Drawing


On Drawing

None Detected69 0018813-069 Plaster, Off White/ Beige, 23°C

On Drawing


On Drawing


On Drawing


PLM REPORT SUMMARY

EPA Method 600/M4-82-020; 600/R-93/11

035.90735.2015.0001

Date Analyzed:


Englewood CO 80112



0018813

ATC Job No.:


Darrel Hart




Identification:

Test Method:

N/A

Batch No.:

10/17/2014

Page 1 of 1

Customer:

035.09316.0001




www.cardnoatc.com

PLM samples were analyzed utilizing the Environmental Protection Agency's Test Method: Method for the Determination of Asbestos in Building Materials (EPA 600/R-93/116. July, 1993). Reporting Limit <1% Asbestos. Additional treatment and tests may be required to accurately define composition (i.e. ashing, extractions, acetone treatment, andTEM). Unused portions of samples are archived for one year unless client requests special handling.

Asbestos content of mastic/adhesive is separated from total percent asbestos and other materials.

Laboratory analysis was accomplished utilizing an Olympus BH-2 polarized light microscope. The microscope is equipped with dispersion staining lenses.

Cardno ATC is accredited by NVLAP Bulk Asbestos Sample Quality Assurance Program (Lab Code 102031). Cardno ATC participates in the NVLAP Bulk Asbestos Sample Quality Assurance Program and maintains an in-house QC/QA program for bulk samples whereby 10% of all submitted samples are reanalyzed and documented in a Quality Control Manual. Cardno ATC also participates in a quarterly round robin QC/QA program for bulk samples with several accredited laboratories throughout the United States. Current and past QC/QA program results are available in the laboratory for inspection.

Samples were analyzed by Jeff Lomme, Laboratory Director. Mr. Lomme is a professional geologist who has successfully completed the McCrone Institutes's "Advanced Asbestos Identification" Course.

Approved Signatory :

The non-detection of asbestos fibers in floor tile by PLM is of itself inconclusive. Confirmation by Transmission Electron Microscope (TEM) is recommended for negative floor tile samples.

This report must not be used by the client to claim product endorsements by NVLAP or an agency of the U.S. government. This test reports only to the items stated.

PLM Analysis Methodology

Laboratory Equipment

Quality Control

Laboratory Personnel

NVLAP LAB CODE 102031-0Jeff Lomme


14

APPENDIX B

SITE DRAWINGS:

BULK SAMPLE LOCATION DRAWINGS

ACM LOCATION DRAWINGS

1

2

3

63

64

19

21

52

46

54

51

50

42

18

57

15

56

6

7

66

47

55

67

26

20

25

27

41

8

43

13

28

29

62

69

71

70

53

9

10

11

49

6017

44

59

58

48

45

31

38

32

33

35

36

37

16

34

39

68

22

4

5

40

24

12

61

14

30

23

65

AP

PR

OV

ED

B

Y:

PR

OJE

CT

N

UM

BE

R:

FIG

UR

E

DR

AW

N B

Y:

DA

TE

:

AC

M &

A

CM

S

am

ple

L

oc

atio

ns

LO

NG

MO

NT

, C

O

1512 M

AIN

S

TR

EE

T

LO

NG

MO

NT

A

RM

OR

Y

1

35.09316.0001

RA

10

/2

1/1

4

AA

Documents

ASBESTOS-CONTAINING MATERIALS SURVEY LONGMONT …