Amsterdam TCM 127

Radiophone / Cassette

Operating instructions

Amsterdam d 1 12.08.1999, 7:13 Uhr1

2

3

16

1

13 1217

11

874 52 6

10

9

14151819

17

1

4

12

3

16

Remote control RCT 07 (optional)

Amsterdam d 1 12.08.1999, 7:14 Uhr2

65

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Contents Radio, Cassette, Changer (Option)

Quick reference ............................ 73

Select operating mode................. 79Audio mode ........................................... 79

Radio operation with RDS ........... 79AF - Alternative Frequency ................... 79REG - regional programme .................. 79Selecting a waveband .......................... 80Station tuning ........................................ 80

Seek tuning / ............................... 80Manual tuning with << / >>................ 80

Entering the frequency directly ............. 80Scrolling through the broadcastingnetworks (FM only) ............................... 81Storing radio stations ............................ 81Automatically storing the stations withthe strongest reception usingTravelstore ............................................ 81Recalling stored radio stations ............. 82Selecting the seek-tuning sensitivity .... 82Switching from stereo to monoFM only) ................................................ 82

Traffic programme stationreception with RDS-EON ............. 83Switching traffic announcementpriority on/off ......................................... 83

Adjusting the volume for trafficannouncements and the beep tone .. 83

Important information .................. 67Safety standards ................................... 67General information .............................. 67

Effects of radio frequency energy ..... 67Safety information ................................. 67

Traffic safety ...................................... 67Using the telephone while driving ..... 67Using the telephone in critical areas . 68Emergency calls ................................ 68

Installation ............................................. 68Notes on connecting a CD changer,an amplifier or the infrared remotecontrol: ............................................... 69

Accessories .......................................... 69

KeyCard and SIM card ................. 70Basic information .................................. 70

Second KeyCard/SIM card ............... 70Wrong KeyCard ................................. 70

Starting up the Radiophone.................. 70Resuming equipment operation after the power has been disconnected ... 70Selecting the language for the display71

Removing the KeyCard/SIM card ......... 71Train KeyCard/SIM cards ..................... 71DSC learn mode ................................... 72Displaying the radio pass data ............. 72Optical warning of anti-theftprotection .............................................. 72Care of your KeyCard/SIM-Card .......... 72

Beep tone ............................................. 83Switching off the beep tone............... 83

Automatic seek-tuning start .................. 83

Operating the cassette deck ....... 84Inserting the cassette ........................... 84Ejecting the cassette ............................ 84Fast forward/rewind .............................. 84Selecting titles with S-CPS ................... 84Changing the track (Autoreverse) ........ 84Tape equalisation ................................. 85Dolby B NR* .......................................... 85Listening to the radio while fastforwarding/rewinding the tape with RM(Radio Monitor) ..................................... 85Care instructions ................................... 85

CD changer operation (optional) 86Switching CD changer operation on ..... 86Selecting the CD and the track ............ 86MIX ........................................................ 86

Programming with DSC ............... 87Overview of the DSC defaultsettings.................................................. 91

66

Contents Telephone

Operating the telephone .............. 94General information .............................. 94

Emergency calls ................................ 94PIN code(Personal Identification Number) .......... 94Inserting the SIM card/entering your PIN code ......................... 94Reactivating the SIM card .................... 94Making your first telephone call ............ 95GSM emergency calls .......................... 95

Quick reference ............................ 96

Using the telephone ..................... 99GSM network service area ................... 99Switching to telephone mode ............... 99Dialling a telephone number ................. 99Manual .................................................. 99Using speed-dialling . . . ..................... 100

. . . directly from the memory bank: 100

. . . directly from the SIM cardmemory bank: ........................... 100

. . . from the telephone book ........... 100Redial function .................................... 100

Automatic ........................................ 100Manual ............................................. 100

Answering/ending a call ..................... 101Call waiting (2nd caller) ...................... 101Broker’s call/hold ................................ 101Conference calls ................................. 102Making telephone calls using thehandset (special accessory) ............... 102

Phone book menu ...................... 103How to enter a name/text ................... 104

Start the entry .................................. 104Entering letters/characters .............. 104Capital and small letters .................. 104Moving the cursor in the entrytext box ............................................ 104Inserting characters ......................... 104Deleting characters ......................... 104

Finding an entry by name ................... 105Show my phone number ..................... 106Prevent access ................................... 106Check capacity ................................... 106Add entry ............................................ 107Finding an entry by position ............... 107

Programming with DSC ............. 108Programming in the setup menu .... 109

Ringing tone volume ....................... 110Hands-free volume .......................... 110Handset volume .............................. 110Automatic answer ............................ 110Automatic redial .............................. 110Operating mode............................... 110Extended menu ............................... 110Ringing tone .................................... 111SMS tone ......................................... 111My phone number ........................... 111Call meter format ............................. 111AOC parameters (Advice of Charge) 111Set charge parameters .................... 112

Audible call timer ............................. 112PIN code .......................................... 112Alter access code ............................ 113Master clear ..................................... 113External alarm ................................. 113Hands-free channel ......................... 114TA during call .................................. 114Overview of the basic factorysettings in the set-up menu ............. 114

Programming in the Call Menu ....... 115Call mailbox ..................................... 116Received SMS messages ............... 116Selecting the message .................... 116Reading messages ......................... 116Clearing messages ......................... 116Sending SMS messages ................. 117Network selection ............................ 118Cell Broadcast ................................. 119Call meters ...................................... 120Call forwarding ................................ 120Call barring ...................................... 120Phone lock ....................................... 121Fixed dial numbers .......................... 121Closed user group ........................... 122

Overview of the basic factory settingsin the call menu .................................. 122

Glossary ...................................... 123Specifications ............................. 124Blaupunkt telephone help line ............ 125

67

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Effects of radio frequency energy

Your Radiophone is both a transmitter anda receiver. It generates minimum amountsof energy in the radio frequency range. Whileit is in use, the GSM system keeps a con-stant check on both the frequency and thepower.

Warnings that using mobile telephones maybe hazardous to your health have recentlybeen a topic of public discussion. For yearsnow, research on the effects of radio fre-quency energy emitted by FM technologyhas concentrated on possible adverse ef-fects to your health. Scientists have alsobegun researching the latest radio technol-ogies such as GSM. According to the re-search results and by complying with thecorresponding safety standards, it is safe tosay that this product can be used withoutreservations.

When the Radiophone is installed properlyin your vehicle, using it is even safer thanusing a portable cellular phone.

If you should still be concerned about theeffects of radio frequency energy, there is alot you can do personally to ensure that youare exposed to a minimum of these radiowaves. Of course, it will help to reduce yourcall time to a minimum but it is especiallyimportant to heed the following tips on us-ing this equipment.

Important information

Safety standards

The mobile telephone has been manufac-tured in accordance with all of the applica-ble RF safety standards and recommenda-tions determined by the government officesand organisations responsible (e.g. the VDEstandard DIN-0848).

General information

The telephone function of your Radiophoneis based on the GSM radio telephone stand-ard. This standard was developed for usein Europe and many other countries.

Using the mobile Radiophone, you canmake the same telephone calls as you canwith a cellular phone.

This assumes that the GSM radio networkis available at your location and that youhave access privileges and a valid SIM card.This SIM card must be inserted into the unit(if necessary, refer to the information in thesection on “KeyCard and SIM card”).

Safety information

Traffic safety

Traffic safety always has the highest priori-ty. As the driver of a motor vehicle, it is yourresponsibility to pay attention to the trafficsituation at all times. Never use your carradio in a way that could distract you.Please keep in mind that you travel a dis-tance of 14 m per second at a speed of only50 km/h.Should the traffic situation become particu-larly demanding, we advise you not to usethe radio.Always make sure that you are still able tohear any warning signals coming from out-side of your vehicle, such as police or fireengine sirens, so that you can react accord-ingly.Consequently, you should always select amoderate volume for playing your car radiowhile you are driving.

Using the telephone while driving

Please observe all laws and regulations re-garding the use to mobile telephones inmotor vehicles.• Concentrate fully on your driving.

• Stop at a safe place before using thetelephone.

68

Reactivate the telephone:• Press briefly.

Emergency calls

As with every other mobile telephone, theRadiophone operates using a combinationof mobile radio and cross-country networks,radio signals and functions programmed bythe user. As a result, there is no guaranteethat your call will always go through. Neverdepend exclusively on a mobile telephoneor similar equipment under life-threateningcircumstances (e.g. in medical emergen-cies).

The telephone interface of the Radiophoneis only able to make and receive calls whenit is activated and located in an area servedby the radio network and when the signal isstrong enough.

Emergency calls may not be possible on allmobile telephone networks or only if certainnetwork services and/or certain performancefeatures are active. Contact the local net-work operators for more detailed informa-tion.

Under certain circumstances, some net-works require that a valid SIM card is in-serted into the unit.

In the event that certain functions (incom-ing call barring, call number barring, closed

• If otherwise unavoidable:Use only hands-free operation if youhave to use the telephone while youare driving.

Traffic safety always has the highest priori-ty.

Using the telephone in critical areas

Always switch off the mobile telephone inareas where it is forbidden to use a mobiletelephone or if this equipment could causeelectromagnetic interference or otherwisedangerous situations.

Using the telephone can result in interfer-ence with the correct functioning of medicalequipment which is not sufficiently shield-ed, particularly near the antenna. Pleaseconsult a doctor or the manufacturer of themedical device if you have any questions.Other electronic equipment can also be af-fected by electromagnetic interference.

If you are in an area where there is dangerof explosion, e.g. petrol stations, chemicalfactories or other places where blasting workis being done, switch your telephone off.

Switching off the telephone:• Press for approx. 2 seconds.“TELEPHONE OFF” will appear in the dis-play.

user group, AOC, system barring, keypadbarring, etc.) are activated, it may be nec-essary to deactivate them before placing anemergency call.

Please read this instruction manual for fur-ther information and consult your local net-work operator.

When placing an emergency call, be sureto supply all the necessary information asaccurately as possible. Remember that yourmobile telephone may be the only means ofcommunication at the scene of an accident.Do not hang up until you are told to do so.

Also read the information in the section on“Telephone operation – GSM emergencycalls”.

Installation

Have the Radiophone installed in your ve-hicle and serviced by a trained service tech-nician only. Faulty installation or servicingcan be dangerous and will result in the ex-piry of your guarantee.

If the vehicle is not adequately shieldedagainst radio frequency signals, electronicfuel injection systems, electronic ABS sys-tems, electronic cruise control systems orother electronic equipment may experiencemalfunctions.

69

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

This equipment must not be operated with-out a suitable externally mounted GSM orcombination antenna. The equipment includ-ing the GSM or combination antenna mustbe installed by an authorised Bosch servicecentre only.

To ensure trouble-free operation, the posi-tive power supply line must be connectedvia the ignition and the permanent +12 Vlead.

Do not ground the speaker outputs!

Notes on connecting a CD changer, anamplifier or the infrared remote control:

If installation conditions are unfavourable,connecting such accessories as a CDchanger, an amplifier or infrared remotecontrol may, in rare cases, lead to interfer-ence with the operation of the telephone.This may result in interference noise, dete-rioration of transmission quality or connec-tions being cut off. In this case, please checkthe wiring or contact one of our authorisedservice centres.

Accessories

Use Blaupunkt-approved accessories andspare parts only.

You can use the following Blaupunkt prod-ucts with this car radio:

Changer:

CDC A06 oder A 072 (direkt)

Remote control:

Using the infrared remote control RCT 077 607 570 510 you can conveniently controlall of the most important functions of yourRadiophone from the steering wheel.The operating functions are described in theQuick References.

Handset

Using the Blaupunkt handset 7 607 570 512it is possible to place telephone calls with orwithout the hands-free function.The system will switch automatically fromhands-free to handset operation when thehandset is removed from the cradle.

Warning:

There is a relatively strong magnet built intothe handset.

Keep away anything which will react to mag-netic influence, e.g. diskettes, bank cards,etc. Important data may be deleted.

Amplifier:

All Blaupunkt amplifiers.

70

If you attempt to insert a different kind ofcard (e.g. telephone or credit card), “CHECKKEYCARD” or “PRÜFE KEYCARD” will ap-pear in the display for approx. 2 sec.

Remove the wrong card and replace it witha valid KeyCard or SIM card.

Starting up the Radiophone

• Switch the unit on (press 1).

Important!The Card tongue must protrude - theninsert the KeyCard included with theRadiophone into the slot with the con-tact surface facing up.Do not try to insert the KeyCard whenthe tongue is retracted as this maydamage the KeyCard mechanism.

The Radiophone is now ready for operation.

Resuming equipment operation afterthe power has been disconnected

If the Radiophone is disconnected from thebattery (e.g. during repairs) and then recon-nected, a trained KeyCard or the master SIMcard is required to resume equipment oper-ation and to reactivate the other trained SIMcards.

Second KeyCard/SIM card

If you use a second KeyCard or a SIM card,the settings will be transferred from the firstKeyCard.

It is possible to store the following functionsas personal settings on the second Key-Card:

Station presets, treble, bass, balance andfader, Loudness on/off, TA (traffic an-nouncement volume), VOLUME FIX.

The two KeyCards and the first two SIMcards will store the last setting selected forthe waveband, bass/treble, fader/balance,station settings, station presets, VOLUMEFIX.

When you insert your KeyCard or one of thefirst two SIM cards, you will find that theequipment switches onto the basic settingsyou have already programmed.

Wrong KeyCard

If a KeyCard from another radio is insertedinto the unit, “KEYCARD ERROR” will ap-pear in the display. Please do not try to op-erate the equipment.

After approx. 8 sec. the radio will switch offautomatically.

If the wrong KeyCard is inserted four times,the waiting time will increase to one hour.

KeyCard and SIM card

KeyCard

Basic information

One KeyCard is included with the Radio-phone.

The car radio can also be operated with asecond “trained” KeyCard or with one of upto 30 trainable SIM cards.

Using the KeyCard it is possible to activatethe following operating modes:

Radio, tape deck, CD changer (optional),AUX, telephone emergency call.

Using the SIM card it is possible to activateall operating modes.

The SIM card also incorporates the anti-theftfunctions.

If necessary (in the event of loss or dam-age), it is possible to purchase a KeyCardor SIM card from an authorised dealer.

71

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

a) Training or deleting the KeyCard/SIM card with DSC

DSC – LEARN CARD

One KeyCard or up to 30 SIM cardscan be trained or replaced as addition-al cards.

• Insert the first KeyCard (includedwith the Radiophone) into the unitand switch the unit on.

• Press DSC/OK and press / toselect “LEARN CARD”.

• Press DSC/OK briefly.

“CHANGE CARD” will appear in thedisplay.

• Remove the first KeyCard and in-sert the new card (KeyCard or SIMcard).

After insertion of a SIM card only: Thedisplay shows “NAME?”.If you wish, you can now enter a nameof up to 8 characters.If necessary, refer to the section on“How to enter a name/text”.

• Press DSC/OK.

• Enter the PIN code and press DSC/OK.

After “CODE OK”, the display willshow, for example, “SIM CARD 23 AC-

Selecting the language for the display

At the factory the texts for the display areset to English.You can display the texts in other languag-es if you wish.• Press DSC/OK.

• Press / until “LANGUAGE” appearsin the display.

• Press DSC/OK and << / >> to selectthe language.

• Press DSC/OK and CL one after theother.

Removing the KeyCard/SIM card

Never forcibly pull out the card!You may destroy it.

• First push the card in gently towardsthe unit.

The KeyCard/SIM card will eject slightly sothat you can remove it.• Remove the card.When you remove the card for the first time,“LEARN CARD” will appear in the display.Now you can train additional cards (refer to“Train SIM cards”).After this process has ended, the Radio-phone will switch off when the card has beenremoved.

Train KeyCard/SIM cards

In the initial programming process you caneasily train the second KeyCard and up to30 SIM cards.In order to do this the Radiophone must beswitched on and the original KeyCard insert-ed.• Remove the original KeyCard and in-

sert the first SIM card.“NAME?“ will appear in the display.

If you like, you can enter a name of up to 8characters. Please refer to “How to enter aname/text”.

If you would like to skip this function or afteryou have entered the name:• Press OK.The first SIM card has been programmed.“TERMINATE? PRESS OK” will appear inthe display. Now you can programme addi-tional cards.

To finish the programming process:• Press OK.The SIM card trained first assumes the ad-ditional function of master SIM card. OtherSIM cards can only be trained using eitherthe master SIM card or the KeyCard.

There are two basic ways in which you cantrain other SIM cards:

72

CEPTED” (i.e. the 23rd SIM card hasbeen trained).

The Radiophone can now be operatedusing the new cards.

A maximum of two KeyCards and 30SIM cards can be trained in this way.

If you attempt to program a third Key-Card, the KeyCard which was not partof the programming process will auto-matically become invalid.

If 30 SIM cards have been pro-grammed, it will be necessary to deleteold access authorizations before newcards can be trained.

b) Training new cards after removingthe KeyCard or master SIM card

If this function is activated in the DSClearn mode, it is possible to train an-other SIM card each time the KeyCard/master SIM card is removed. Thisfunction is useful if you want to trainseveral cards one after the other (fleetmanagement).

c) Deleting SIM card authorisations

The authorisation for SIM cards can bedeleted using the CARD LIST in theDSC menu. The master SIM card canbe deleted with a KeyCard only.

DSC learn mode

With this function you can select whetheryou want to train additional SIM cards usingthe DSC menu only or each time after re-moving the KeyCard or the master SIM cardas well.For operating instructions refer to “Program-ming with DSC – LEARN MODE”.

Displaying the radio pass data

Using the KeyCard supplied with your setyou can have the radio pass data such asthe model name, product number (7 6...) andserial number indicated in the display.Please refer to the section on “Programmingwith DSC – READ KEYCARD”.

Optical warning of anti-theftprotection

KeyCard tongue flashes

When the vehicle has been parked and theKeyCard or SIM card removed, the KeyCardtongue can be switched to flash to provideadditional anti-theft protection.For this function to operate properly it isnecessary that the positive power supply lineand the permanent +12 V lead are connect-ed as described in the installation instruc-tions.

Be sure that “KEYCARD LED ON” has beenselected in the DSC mode.If necessary, refer to the section on “Pro-gramming with DSC – KEYCARD LED”.

Switching off the flashing light

The flashing light can be switched off bypushing in the KeyCard tongue gently untilit locks.If you would like to deactivate the flashingtongue altogether, select the “KEYCARDLED OFF” item in the DSC menu:

Care of your KeyCard/SIM-Card

In order to ensure that the card always func-tions correctly, the contacts must be free ofany foreign particles. Avoid direct skin con-tact.Do not subject the cards to direct sunlight.If necessary, clean the card contacts usinga cotton swab dipped in rubbing alcohol.

73

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Switching the unit on/off via the ig-nition:If the equipment has been connectedproperly, it can be switched on and offwith the vehicle ignition.When the ignition has been switchedoff, the unit will emit a double beep toremind you to remove the KeyCard/SIM card before leaving your vehicle.If you switch off the ignition during atelephone call, the Radiophone will re-main switched on until you have com-pleted the call.

Switching the radio on when the ig-nition is switched offWhen the ignition is switched off (cardis inserted) the equipment will continueto function as follows:After you hear the double beep, pressthe knob. The equipment will switchback on. After one hour’s playing time,the Radiophone will switch off auto-matically to prevent the car batteryfrom going dead.

Operation in combination with anignition timerIf the ignition timer has been activatedin the DSC mode, the Radiophone willswitch off as programmed after the ig-nition is switched off (refer to the sec-tion on “Programming with DSC - IGNI-TION TIMER”.

Altering the volumeTurn the knob to alter the volume. Thesetting will appear in the display.When the Radiophone is switched on,it will play at a preset volume (VOL-UME FIX).VOLUME FIX can be altered as de-sired (refer to “Programming with DSC- VOLUME FIX”).The volume can also be altered usingthe remote control (optional) by press-ing V- / V+.

Quick reference for operating the radio, tape deck and CD changer (optional)

1 On/offVolumeTo switch the Radiophone on, pressthe knob (volume control).A valid KeyCard or SIM card must beinserted in the unit already or withinthe next 15 seconds.

Switching the unit on/off with theKeyCard:If the equipment has been switched onby pressing knob 1, then it can beswitched off and on again with theKeyCard or SIM card.This assumes that the program hasbeen switched to “MENU” under“LEARN MODE” in the DSC menu.

Note:Be sure to read the information in thesection on “KeyCard/SIM card anti-theft protection system”.

74

For more detailed information refer to“Programming with DSC - LOUD-NESS”.

3 SRC (Source)You can switch between the operatingmodes for radio, cassette and changer(option) or an auxiliary unit.You can switch from the telephonemenu back to the last operating modeselected.This assumes that you are not talkingon the telephone or trying to place acall.

4 TA (Traffic Announcement = priorityfor traffic messages)If “TA” appears in the display, you willbe able to tune into radio stationswhich broadcast traffic informationonly.Switch priority on/off: press TA.

5 TS / BNDSwitch between the memory levels/wavebands FM, TS (Travelstore), MWand LW.

Additional Travelstore functionStore the nine radio stations with thestrongest reception signals using Trav-elstore : Press BND until you hear abeep or until “TRAVELSTORE” ap-pears in the display.

6Dolby B NR*Cassettes recorded with Dolby B NRwill be played back in the best qualitypossible if “DOLBY” appears in thesecond line.* Noise reduction system manufactured under li-

cence by Dolby Laboratories. The word Dolbyand the double-D symbol are trademarks of Dol-by Laboratories.

7 Eject cassette

Press the button until the cassetteejects.

Track switchPress the button briefly to switch cas-sette playback to the other track (side)of the tape.

2 / AUDPress AUD once:Alter treble and bass settings using therocker switch.

Treble +Treble –Bass –Bass +

Press AUD twice:Alter balance (left/right) and fader(front/rear) settings.

Fader frontFader rearBalance leftBalance right

The settings will be indicated in thedisplay. The last setting made will bestored automatically.Switch off AUD: Press AUD for a thirdtime.If no changes are made for a period of8 seconds, the AUD setting will endautomatically.

Switching Loudness on/off:Press AUD for approx. 1 sec. (beep).The current setting will appear brieflyin the display (ON/OFF).

75

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

8 Cassette loading slotInsert the cassette (side A or 1 facingup, open side to the right).

9 Selection buttons

Radio mode

Entering the frequency directlyYou can enter an FM frequency direct-ly using the selection buttons:First press “0” and then enter the de-sired frequency, starting with the firstdigit. It is only possible to enter fre-quencies between 87.5 and 108. Omitthe decimal point in the entry. PressCL to abort the entry, press OK to con-firm the entry. Once all of the digitshave been entered, the entry will beconfirmed automatically.

Storing radio stationsYou can use the buttons to store thefollowing number of radio stations forthe different wavebands:

FM 19TS (FM-Travelstore) 9MW 9LW 9

To store – During radio operationpress one of the selection presets untilyou hear a beep. If you want to storethe station on a two-digit preset, firstpress “1” and then press the seconddigit within 2 sec. until you hear abeep.

Recalling stored radio stations – Se-lect the desired waveband (select “FM”or “TS” in the FM range) and press thecorresponding button.Activate the presets from 10 to 19 bypressing “1” briefly first and thenpressing the second button within twoseconds.

Tape mode

It is possible to set or correct thenumber of titles to be skipped for S-CPS (Super Cassette ProgramSearch) or fast forward.

CD changer mode (optional)

CDs 1 to 10 can be selected directly(0 = CD 10).

: AF / #Alternative Frequency for RDS opera-tion: When “AF” appears in the displaythe radio will automatically use RDS tofind for the best reception frequencyfor the programme you are listening to.Switching AF on/off: Press AF briefly.

Switching the regional function on/off:Press AF for approx. 2 seconds(beep), “REGIONAL ON” or “REGION-AL OFF” will appear briefly in the firstline in the display.When the regional function is switchedon “REG” will appear in the display onthe right.

; + / 0Press this button before you enter aradio station frequency directly.

76

= MIX / *Radio operation

Switch seek-tuning sensitivity:Press button briefly.If “lo” is displayed, the radio will onlypick up strong, local stations (normalsensitivity).If “lo” does not light up, the radio willalso pick up weaker, more distant sta-tions (high sensitivity).

CD changer operation (optional)

MIX CDThe tracks of a CD will be played backin random order.The following CDs will also be selectedat random.

MIX OFFThe MIX function is switched off.Press MIX until the desired functionappears in the display.

g) lo - Seek tuning sensitivityh) 19/T9 - Indicates on which button

the station currently play-ing is stored (1-19)/Trav-elstore (1-9)

i) - Call forwarding is activej) - Indicates that a SMS

message is storedk) - Also appears when a

voice message has beenreceived

l) - Connection with GSMradio network

m) - GSM field strength indi-cator

n) AF - Alternative frequency forRDS

o) DOLBY - Dolby B NRp) MTL - Metal or CrO2 cassettes

are currently playingq) RM - Radio Monitor (listen to

radio during tape fast for-ward or rewind)

r) T: 11 - CD track numbers) 02 . 32 - CD time (time played)t) MIX - CD track random play

> Display

Radio operation

d e f hg l

a

i j k m n

Cassette operation

b

o p q

Changer operation (optional)

c

r s t

a) NDR1 NDS - Station nameb) Side 2 - Side 2 of the cassettec) CD 02 - CD numberd) FM - Radio wavebande) TP - Radio station broadcast-

ing traffic information (iscurrently being received)

f) TA - Traffic announcement pri-ority

77

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

@ Rocker switch

Radio operation

/ Seek tuningUpwardsDownwards

<< / >> Up or down in increments(for FM only when AF is switchedoff)

For FM only:<< / >> Scroll through the station broad-

casting network when AF isswitched one.g. NDR 1, 2, 3, 4, N-JOY.

Tape operation

Fast forward

Fast rewind

/ Select title (S-CPS)ForwardsBack

Stop this function by pressing orthe opposite button.

? Anti-theft card protection systemIn order to operate the radio equip-ment it is necessary to first insert theKeyCard included with the unit or aKeyCard you have trained accordinglyor a programmed SIM card.

KeyCard

Please read the information in the sec-tion on “Anti-theft card protection sys-tem” carefully.

Flashing card tongueIf the radio has been switched off andthe KeyCard or SIM card removed, thecard tongue will flash as additionaltheft protection if the correspondingsetting has been activated.For more detailed information, pleaserefer to “Programming with DSC”.It is possible to switch off the flashinglight by pressing the card tongue ingently until it locks into place.

78

CD changer operation (optional)

Select CD

Up

Down

Select track

Up: Press briefly.CUE - fast forward (audible): Holdbutton pressed down.

Down: Press two or more timesone after the other.Restart the same track: Pressonce briefly.REVIEW - fast reverse (audible):Hold button pressed down.

Additional rocker switch functions:Additional settings possible withAUD 2DSC mode CThe corresponding function must beactivated.

A MEUnit:

Telephone functions only.

Remote control:

During radio operation it is possible torecall stored radio stations in ascend-ing order.During CD changer operation, the CDsare selected in ascending order.

B CL (CLEAR)Press this button to quit the currentlyactive menu item in the DSC mode.Any changes made will not be stored.Press CL again to quit the DSC mode.

Cancels direct frequency entry.

C DSC / OKDSC (Direct Software Control)Use DSC to adjust the programmablebasic settings.OKPress to store the altered settings.

Activate DSC: Press the button briefly.Select function: Press / .Display setting adjustments: PressDSC/OK.Alter settings: Press << / >>.Store: Press OK.Quit DSC: Press CL.If you quit DSC by pressing CL beforeyou press OK, any changes made tothe settings will not be stored.For more information refer to “Pro-gramming with DSC”.

79

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

While searching for the strongest receptionsignal, the radio may switch to mute briefly.

If “SEARCH” appears in the display whenswitching on the radio or recalling one of thestored frequencies, the unit is automaticallysearching for an alternative frequency.

“SEARCH” will disappear from the displaywhen the alternative frequency has beenfound or after the frequency band has runthrough completely.

If the reception quality of the selected pro-gramme becomes poor:• Tune into a different station.

REG - regional programme

Certain radio programmes are split up attimes into regional programmes offering lo-cal information. The 1st programme broad-cast by NDR, for example, offers pro-grammes with different contents in the north-ern states of Germany including Schleswig-Holstein, Hamburg and Lower Saxony atcertain times of the day.

If you are listening to one regional pro-gramme and move to an area where anoth-er linked regional programme becomesstronger, the unit will switch to that pro-gramme.

Select operating mode

Audio mode(Radio, tape deck, CD changer (optional),auxiliary source)

During audio operation you can use SRC toswitch between radio, cassette and chang-er (option) or an auxiliary sound source.

When in telephone mode, you can switchback to the audio source used last by press-ing SRC.

Telephone operation has priority. As a re-sult, you cannot switch to audio mode un-less you are not currently talking on the tele-phone or trying to place a call.• Press SRC repeatedly until the func-

tions of the audio source you wish tolisten to appear in the display.

You cannot select tape or CD changer op-eration unless a cassette/magazine contain-ing CDs has already been inserted.

If an empty magazine has been inserted,“NO CD” will appear in the display.

An auxiliary source can only be selected ifa Blaupunkt changer has not been connect-ed to the system. “AUXILIARY SOURCEON” must be set in the DSC menu.

Radio operation with RDS (Radio Data System)

The Radio Data System offers you addedconvenience when listening to FM radio sta-tions.

More and more radio stations have begunto broadcast RDS information along withtheir regular programmes.

As soon as a programme has been identi-fied, the station name including a regionalidentifier, if applicable, will appear in the dis-play, for example, NDR1 NDS (regional pro-gramme in Lower Saxony, Germany).

When RDS is activated, the preset buttonsbecome programme buttons. You now knowexactly which programme you have tunedinto, making it easy to find the desired sta-tion quickly.

RDS also offers other advantages:

AF - Alternative Frequency

The AF (Alternative Frequency) functionmakes sure that the radio always automati-cally tunes into the strongest frequency ofthe currently selected programme.

If this function has been activated “AF” willappear in the display.

In order to switch this function on or off,• press AF/# briefly.

80

Manual tuning:

• Press << / >>; the frequency willchange in degrees in the downwardsor upwards direction.

If you hold down the right or left part of therocker switch, the frequency scan will speedup in the corresponding direction.

Entering the frequency directly

For FM or FMT, it is possible to enter thestation frequency directly.

Start your entry• by pressing 0.

• Then enter the frequency, beginningwith the first digit. You need not entera decimal point.

Press CL to cancel this process or OK toconfirm your selection.

Station tuning

Seek tuning /

• Press / ; the car radio will automati-cally search for the next station.

If you hold down / (also applies to re-mote control operation), seek tuning willspeed up in upwards or downwards direc-tion.

Seek tuningUpDown

<< / >> Up/Down in increments (for FM onlywhen AF is switched off)

Manual tuning with << / >>

You can also tune in a station manually.

Important:AF must be switched off (i.e. the “AF” or“REG” symbol does not light up in the dis-play).

If necessary, deactivate this function:• Press AF/#.

If you wish to continue listening to the firstprogramme, switch REGIONAL ON by• pressing AF/# for approximately 1 sec-

ond until “REGIONAL ON” appears inthe first line.

When the regional function has beenswitched on “REG” will replace “AF” in thedisplay.

If you leave the service area of the regionalprogramme you are currently tuned into, orif you would like to take advantage of thefull RDS service, switch to “REGIONALOFF”.• Press AF/# for approximately 1 second

until “REGIONAL OFF” appears.

Selecting a waveband

You can select between the following wave-bands:

FM 87.5 - 108 MHzMW 531 - 1602 kHzLW 153 - 279 kHz• Use BND to select the waveband.

Press repeatedly if necessary.

81

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Scrolling through the broadcast-ing networks (FM only)

You can use the << / >> buttons to tune intostations in your reception area.If it is possible to receive several pro-grammes in the same broadcasting network,you can scroll through them in the forwardsdirection by pressing >>, or backwards us-ing the << button, e.g. NDR 1, 2, 3, 4, N-JOY.You must have tuned into these stations atleast once previously and “AF” must be ac-tive (lights up in the display).

Start Travelstore, for example:• Press BND for 2 seconds; the system

starts to run through the frequencyband.

If “AF” does not light up,• press AF/#.This fulfils the requirements for selectingstations with << / >>.

Storing radio stations

You can store the following number of sta-tions on the selection buttons for each ofthe individual wavebands:

FM 19TS (FM-Travelstore) 9MW 9LW 9• Use BND to select the desired wave-

band.

• Select a radio station using the rockerswitch (automatically with / or man-ually with << / >>).

• Press the desired selection button forapprox. 1 sec. until you hear a beep.

If you want to store the radio station on atwo-digit preset,• press button 1 briefly and the second

button within 2 sec. until you hear abeep.

You have now stored the radio station.The station preset will appear in the display.

Note:If you attempt to store a station which is al-ready stored, the number of the correspond-ing selection button and the memory bankwill flash in the display briefly if you are us-ing the same memory bank.

Automatically storing thestations with the strongestreception using Travelstore

You can automatically store the nine mostpowerful FM stations of your current recep-tion area sorted according to their signalstrength. This function is particularly conven-ient during longer trips.• Press BND/TS for 2 seconds.“TRAVELSTORE” will flash in the display.The nine FM stations with the best recep-tion will be stored automatically in the FMT(FM Travelstore) memory bank. When thisprocedure has been completed, the radiowill switch to the station with the best re-ception stored on selection button 1.If desired, stations can also be stored man-ually on the Travelstore memory bank (re-fer to “Storing radio stations”).

82

Recalling stored radio stations

You can recall any stored radio station atthe touch of a button.• Press BND/TS repeatedly until the de-

sired waveband appears in the display.

• Press the corresponding selection but-ton briefly.

If you wish to recall a station stored on atwo-digit preset (e.g. preset 19) first press 1and then 9 within the next 2 seconds.

Selecting the seek-tuning sensi-tivity

You can alter the automatic seek-tuningsensitivity.If “lo” is displayed, the radio will only pick upstrong, local stations.If “lo” is switched off, the radio will also pickup weaker, more distant stations.To switch the seek tuning sensitivity:• Press *.The sensitivity level can be selected sepa-rately for both modes. (Please refer to thesection on “Programming with DSC – DX-LEVEL / LO-LEVEL”).

Switching from stereo to mono(FM only)

Every time the radio is switched on, stereoplayback will be activated automatically.

The unit will gradually switch to mono if thereception deteriorates beyond a certainpoint.

83

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Switching traffic announcementpriority on/off

If the priority for traffic announcement pro-grammes is activated, “TA” will light up inthe display.

To switch the priority on or off:• Press TA.If you press TA while a message is beingbroadcast, this message will be interrupted.

The unit will then switch back to its previousstatus. The priority for all other traffic mes-sages will remain active.

Please note that several buttons have nofunction while traffic announcements arebroadcast.

Adjusting the volume for trafficannouncements and the beep tone

Although this volume was preset at the fac-tory, you can alter it using the DSC function(see “Programming with DSC – TA VOL-UME”).

Beep tone

When a traffic programme station is activat-ed (“TA” in the display), you will hear a beeptone after approximately 30 seconds if youleave the reception area of the traffic pro-gramme station you are currently tuned into.

Traffic programme station reception with RDS-EON

The abbreviation “EON” stands for En-hanced Other Networks which means thatinformation is exchanged between the ra-dio stations belonging to the same broad-casting network.

Many FM broadcasters provide traffic mes-sages for their service area at regular inter-vals.

All traffic programme stations transmit aspecial carrier signal along with their pro-grammes, which is decoded by your car ra-dio. If this signal is identified, “TP” will ap-pear in the display (Traffic Programme).

In addition to these, there are also stationswhich do not actually transmit traffic pro-grammes themselves, but by using RDS-EON it is possible to receive the traffic mes-sages broadcast by another traffic pro-gramme station in the same radio network.

If you wish to have the priority for traffic an-nouncements activated while listening toone of these stations (e.g. NDR3), “TA” mustappear in the display.

If a traffic announcement is broadcast, theradio will automatically switch to the linkedtraffic programme station (in this case,NDR2) for the duration of the message andreturn to the original programme (NDR3)afterwards.

You will also hear this beep if you press astation preset button for a radio station whichdoes not broadcast the TP signal.

Switching off the beep tone

a) Tune into another station providingtraffic information:

• Press the rocker switch or

• press a preset button for a radiostation which has a traffic pro-gramme station allocated to it.

orb) Switch off the priority for traffic an-

nouncements:

• Press TA.“TA” will disappear from the dis-play.

Automatic seek tuning start(tape and CD changer operation)

If you leave the reception area of the cur-rent traffic programme station while listen-ing to a tape or CD, the system will auto-matically start searching for a new TA pro-gramme.

84

Operating the cassette deck

The equipment must be switched on.

As soon as you insert a cassette, the setwill automatically switch to cassette opera-tion.

The cassette will not begin to play

a) as long as a telephone call is inprogress or being placed, or

b) as long as a priority traffic announce-ment is playing.

Inserting the cassette

• Switch the unit on.

• Insert a cassette.The cassette will be pulled into the unit au-tomatically and Side A or 1 will begin to play.The display will indicate the cassette func-tions.

Insert the cassette with side A or 1 facing upand the open side facing to the right.

Ejecting the cassette

• Press for approx. 2 sec.The cassette will eject.

The number of titles to be skipped will ap-pear in the display.Correct by pressing the opposite button.During fast forward or rewind, up to 9 titlescan be skipped. The desired number canbe entered or corrected with the selectionbuttons.To stop the function immediately, press .Important for S-CPS: There must be an un-recorded tape portion of at least 3 secondsbetween the titles.

Changing the track (Autoreverse)

Switch the direction in which the tape is play-ing during playback• by pressing .When the tape has reached the end, it willswitch automatically to the other track. “SIDE1” or “SIDE 2” will appear in the display.

Note:If there is too much tension on the tape whileit is playing, it may switch to the oppositetrack before it has reached the end. Checkto see if the tape is wound correctly. It oftenhelps to rewind the cassette completely.

Fast forward/rewind

Remote control

Fast forward

Fast rewind

Using the remote control you can start to fastforward/rewind the tape by pressing / formore than 1 second.

/ Select title (S-CPS)(also possible using the remote control)

forwardsback

Stop function by pressing .

Selecting titles with S-CPS(Super Cassette Program Search)

To repeat or skip titles on the cassette press (forwards) / (back).

You can skip up to 99 titles• by pressing the rocker switch as often

as required.

85

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Listening to the radio while fastforwarding/rewinding the tapewith RM (Radio Monitor)

While fast forwarding or rewinding the tape,you can listen to the radio instead of theusual muting (also applies for S-CPS).The “RAD. MONITOR ON” setting must beactivated in DSC mode.Refer to “Programming with DSC – RAD.MONITOR” if necessary.

Care instructions

You should use only C60/C90 tape cas-settes in your car. Protect your cassettesagainst dirt, dust and temperatures over50 °C. Allow cold cassettes to warm upsomewhat before playing them to ensurethat the tape plays smoothly. Malfunctionsin playback or sound may be caused by dirtbuild-up on the pinch roller and the audiohead after approx. 100 hours of operation.To remove normal dirt build-up clean theequipment with a cleaning cassette. In morestubborn cases, use a cotton swab dippedin rubbing alcohol. Never insert hard instru-ments into the tape deck.

Tape equalisation

The unit is able to identify the following tapetypes: iron oxide, chrome oxide or metal; itwill switch to the corresponding setting au-tomatically.When metal or chrome cassettes are played“MTL” will light up in the display.

Dolby B NR*

This equipment is able to play back cas-settes which have been recorded using Dol-by B NR or without noise reduction.There is far less tape noise and the sounddynamics are correspondingly greater oncassettes recorded using Dolby NR*.“DOLBY” will light up in the display whenDolby B NR is switched on.

Switching on/off:• Press .

* Noise reduction system manufactured under licenceby Dolby Laboratories. The word Dolby and the dou-ble-D symbol are trademarks of Dolby Laboratories.

86

CD changer operation (optional)

You can use this equipment to convenientlyplay back CDs with one of the following Blau-punkt CD changers: CDC A06 or A 072 (di-rectly) or CDC-A 05/-F 05/A 071 (with anadapter).The changer is not included with this equip-ment and can be purchased separately at aretail outlet.

Note:

Use only standard circular CDs measuring12 cm in diameter!CDs measuring 8 cm in diameter or CDs indifferent shapes such as a butterfly or beermug are not suitable for playback using thisequipment.This may result in the destruction of the CDor the CD drive.We assume no liability for damage to theequipment caused by playing unsuitableCDs.

Switching CD changer operationon

A magazine containing at least one CD mustbe inserted.

Use SRC to switch the audio source:• Press SRC until the changer functions

appear in the display.

Selecting the CD and the track

Remote control

Select a CD

upwards

downwards

Enter the number of the CD you wish to se-lect directly using the numbers keypad.Use the remote control to select a CD inascending order by pressing the ME button.

Selecting a trackis also possible using the remote control

upwards: press brieflyCUE - fast forward (audible):hold pressed down.

downwards: press briefly twice orrepeatedlyRestart current track: press briefly.REVIEW - fast reverse (audible):hold pressed down.

Press / on the remote control to selectthe track up or down.

MIX

CD tracks can be played in random order.If “MIX” is illuminated in the display, all ofthe tracks on a CD will be played in randomorder.Following this, the next CD will be selectedat random and played, etc.

Switching MIX on/off:• press MIX/* briefly.

87

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Programming with DSC Radio, Cassette, Changer (optional)

The car radio is equipped with DSC (DirectSoftware Control), enabling you to adjustsettings and functions to your personalneeds and to store these settings.

The equipment has been adjusted to defaultsettings at the factory.

There is an overview of the factory defaultsettings at the end of this section so thatyou can reset these settings at any time.

If you wish to alter any programming• press DSC/OK.

Select:

Use the rocker switch / to select themenu item you wish to alter and confirm yourselection by pressing OK.

Alter:

Press << / >> to alter the setting indicatedin the display.

Cancel:• Press CL. The new setting will not be

saved.

Store:• Press DSC/OK.

Exit DSC:• Press CL.

OFF ON

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

StartDSC

^^ ^^

To quit DSC (from any menu item): Press CL

^^

88

You cannot alter the programming forimportant DSC settings unless you haveentered the access code first (refer to theDSC menu item “CHANGE ACCESS-CODE”).

/ Select function<< / >> Make setting

LOUDNESSBoosts low frequencies for morebass, especially at low volume.

LOUD 1 - minimum boostLOUD 6 - maximum boost

MASTER RESETThis menu item will appear only ifa KeyCard is inserted.Important!This function will reset all of thesettings in the DSC menu includ-ing the telephone menu to the fac-tory default settings.

All of the trained KeyCards andSIM cards will be deleted, exceptfor the KeyCard currently in theunit.If this menu item is selected, it willbe necessary to enter the accesscode after OK. Enter the accesscode, press OK.The display will show “MASTERRESET?”: Press CL to cancel thisfunction, press OK to reset all ofthe settings to the default set-tings.

CHANGE ACCESSCODEThe access code is used to ac-cess the important DSC menuitems (also for telephone opera-tion). At the factory, this code isset to “0000”.If you would like to alter it be sureto make a note of the new code!Enter the original code (in thiscase “0000”) and press OK.Enter the new code, press OK.Enter the new code once again,press OK.

IGNITION TIMERUse this setting to ensure that thecar radio will play for a maximumof 90 minutes after the ignitionhas been switched off.0 = ignition timer switched off.

AUXILIARY SOURCEThis menu item will not appear ifa CD changer (A 05 or A 06) hasbeen connected to the system.The default setting is “AUXILIARYSOURCE OFF”.If an external piece of equipmentis connected to the system, thissetting must be switched to“AUXILIARY SOURCE ON”.

VARIOCOLOURAdjusts the colour of the displayillumination to the dashboard illu-mination.

''green ...................................... red

KEY TONEAfter a key is pressed, a shortbeep is emitted as confirmation.Set volume from 0 to 9 (0 = off).

89

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

BEEP Confirmation beep following func-tions which require you to pressthe button for longer than 1 sec.Set volume from 0 to 9 (0 = off).

MUSIC/SPEECHIn future, different RDS radiostations will differentiate betweenmusic and voice programs.The tone setting for voiceprograms ranges between“LEVEL 0 ... 4”.

LEVEL 0:Music/voice is switched off.

LEVEL 1:Linear (no bass, treble, loudnessadjustment).

LEVEL 2-4:Different settings for volume, bassand treble with loudness switchedoff.Test the settings to find out whichone you prefer.

RAD. MONITOR(Radio Monitor)Allows you to listen to the radiowhile fast forwarding/rewindingthe cassette.Switching the Radio Monitor func-tion on/off: Press << / >>.During tape deck operation, “RM”will light up in the display if thisfunction is activated. When thetape is being fast forwarded/re-wound you will be able to hear theradio.

KEYCARD LEDYou can choose between LEDON or LED OFF. The KeyCardtongue will flash if you select LEDON. It acts as additional protec-tion when the set is switched offand the KeyCard has been re-moved.

LANGUAGEThe display texts are available indifferent languages.If “AUTOMATIC” has been select-ed, English will be the languageused for the display texts whenthe KeyCard has been inserted.

If a SIM card is used, the lan-guage selected on the card will bethe language which appears inthe display.

LEARN MODEWith this function you can deter-mine whether additional cards canbe programmed using the DSCmenu only or after the currentlyvalid KeyCard or the Master SIMcard has been removed as well.

MENU –Cards can only be programmedwith the help of the DSC menu.

MENU PLUS –Additional simple method of pro-gramming cards:Remove the KeyCard or MasterSIM card and insert another cardwithin 15 sec.You can continue training cardswith other cards.

90

After OK “CLEAR?” will appear inthe display.Press << / >> to choose betweenCLEAR? and NAME? (alter).Press CL to cancel the process,press OK to confirm the process.If you want to enter/alter names,please refer to “Telephone bookmenu – Add entry”.It is not possible to clear the cardinserted in the set.Note that the master SIM cardcan be cleared with the KeyCardonly.

READ KEYCARDThis menu item will appear only ifa KeyCard is inserted.It is possible to read out the dataon a KeyCard.Using the KeyCard which was in-cluded with the delivery, it is pos-sible to display the equipmentdata such as name, type number(76 ...) and serial number.If you remove the KeyCard whileit is being read, “CHANGE CARD”will appear in the display. It ispossible to read the informationon any KeyCards, even those for

EXTENDED MENUUsing this function it is possible topress << / >> to remove the fol-lowing menu items which arerarely altered.This makes the menu more man-ageable.

OFF –Remove menu items.

ON –All of the menu items are availa-ble.

CARD LISTIt is possible to display a list con-taining all of the valid SIM cards.You can delete individual entriesif you wish.The Master-SIM can be deletedwith a KeyCard only.

WARNING!If the entry is deleted, it will nolonger be possible to operate theunit using this card.

After pressing OK you must enterthe access code and confirm yourentry by pressing OK.The entries can be viewed bypressing / .

different car radios. It is not possi-ble to operate the unit, except toswitch it off. As long as a KeyCardfor this unit is inserted, you canswitch back to radio operation bypressing OK.

LEARN CARDYou can program a second Key-Card or up to 30 SIM cards.Refer to the information on “Key-Cards and SIM cards - Program-ming the KeyCard/SIM card”.

USER MODEYou can choose among the fol-lowing operating modes:RADIO ONLYPHONE ONLYSTANDARD(all operating modes can be se-lected).Any changes will not take effectuntil you have exited the menu.

91

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

LO-LEVEL SENSITIVITYSets the search sensitivity for lo-cal reception.

LO-LEVEL 1 –high sensitivity

LO-LEVEL 3 –normal sensitivit

DX-LEVEL SENSITIVITYSets the search sensitivity for dis-tant reception.

DX-LEVEL 1 –high sensitivity

DX-LEVEL 3 –normal sensitivity

VOLUME FIXAllows you to set the volume atwhich the unit switches on.Use << / >> to set the desired vol-ume. If “LEVEL +00” is selected,the car radio will switch on at thevolume level which was last setbefore it was switched off.

TA VOLUMEThe volume for traffic messagesand the beep can be adjusted.The traffic message will be playedat this volume if the volume cur-rently selected is lower. If the se-lected volume is louder than theTA VOLUME the traffic messagewill be played somewhat louder.

End DSC programming/save changes:• Press DSC/OK.

Overview of the DSC defaultsettings

LOUDNESS LEVEL 3CHANGE ACCESSCODE 0000IGNITION TIMER 00 minAUXILIARY SOURCE SOURCE OFFVARIOCOLOUR greenKEY TONE VOLUME 0BEEP 4MUSIC/SPEECH LEVEL 0RAD. MONITOR AUSKEYCARD LED LED ONLANGUAGE AUTOMATICLEARN MODE MENU PLUS*EXTENDED MENU ONCARD LIST -READ KEYCARD -LEARN CARD -USER MODE STANDARDSENSITIVITY LO-LEVEL 1

DX-LEVEL 1VOLUME FIX LEVEL +20TA VOLUME LEVEL +30

* MENU PLUS = basic settingThe system will reset to MENU after havingprogrammed the first SIM card.

92

93

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Telephone operation

94

PIN code(Personal Identification Number)

Normally, the SIM card will not operate thetelephone until a personal identificationnumber (PIN code) has been entered. ThisPIN code is included with the SIM card whenyou purchase it.

You can alter or even deactivate your PINcode. Refer to “Programming with DSC –PIN CODE”.

Inserting the SIM card/entering your PIN code

• Switch the unit on.With the card tongue protruding, insertthe trained SIM card into the slotwith the contact surface facing up .

“ENTER PIN” will appear in the display.

• Enter the PIN code using the numberkeys, starting with the first digit.

• Press OK or #.If the PIN code has been entered correctly,“CODE OK” will appear in the display fol-lowed by the menu which was used last.

If an incorrect PIN code has been entered,“WRONG PIN-CODE” will appear in the dis-play followed by “ENTER PIN”.

If the PIN code is entered incorrectly threetimes in succession, it is necessary to usethe PUK code (Personal Unblock code) toreactivate the card.

Reactivating the SIM card

The PUK code must be used to reactivatethe SIM card.

The display shows “ENTER PUK”.• Enter your code and press OK to con-

firm.

• Enter a new PIN code.Important!

Make sure you make a note of the new PINcode!

• Confirm your entry by pressing OK andrepeat the entry.

Operating the telephone

General information

Using the Radiophone, you can make thesame telephone calls as you can with a cel-lular phone.

Important: You must be located in an areaserviced by the GSM radio network and havethe access privileges provided by a valid SIMcard. This SIM card must be inserted intothe unit (refer to the section on “KeyCardsand SIM cards” if necessary).

Emergency calls

The number to dial to place an emergencycall in the GSM network anywhere in theworld is 112.

You can place an emergency call by dial-ling this number even without inserting a SIMor KeyCard.

Please read the information in the sectionon “Using the telephone – GSM emergencycalls”.

95

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

GSM emergency calls

The emergency number in the GSM net-work is 112 anywhere in the world.

By dialling 112 you can place an emergen-cy call, regardless of whether or not youhave inserted a SIM or KeyCard.

Any barring codes entered in the system willnot affect the 112 number. It is possible toplace an emergency call as long as the an-tenna symbol is flashing and the signal isstrong enough.

To place the call:• Switch the set on, insert the KeyCard

or SIM card. If you do not enter a card,you must complete the following oper-ating steps within the next 4 seconds.

• Press .

• Dial 112 and press .“Emergency” will appear in the display andthe telephone will place the call.

Making your first telephone call

When the telephone is ready to operate, anantenna symbol will appear in the display(must not flash).

A trained SIM card must be inserted in theunit correctly. If the equipment is not cur-rently in the telephone mode• press briefly.

• Dial the number you wish to call usingthe number keys.

After you have entered the telephonenumber correctly,• press briefly.The telephone will now place the call auto-matically.

To end your telephone call:• Press briefly.

Important!

Do not use the emergency call number un-less there really is an emergency.

When placing an emergency call, be sureto supply all the necessary information asaccurately as possible. Remember that yourmobile telephone may be the only means ofcommunication at the scene of an accident.

Do not hang up until you are told to do so.

96

Quick reference for using the telephone

9 Selection buttonsTo enter a telephone number:Press the corresponding keys briefly.

To use one-touch dialling to call one ofthe first nine phone book numbersstored in the set:Press the corresponding key for ap-prox. 2 seconds.

To use one-touch dialling to call one ofthe first nine phone book numbersstored on the SIM card:Press *, then press the correspondingkey for approx. 2 seconds.

Enter the name. Please refer to thesection on “How to enter a name/text”.

To answer a call: Press one of the but-tons on the right side of the set.

: AF / #Enters special characters.

3 SRC (Source)Press SRC briefly: The telephonefunctions will end and the set will auto-matically switch back to the audiomode used last (radio, tape deck oroptional CD changer).

The telephone mode has priority. It isnot possible to switch to an audiomode if you are already talking on thetelephone or trying to place a call.

If you press SRC briefly while the tele-phone is ringing: the caller will receivethe information that the party he is call-ing is unavailable.Press SRC for approx. 1 second: busysignal.

4 TA (Traffic Announcement = Priorityfor traffic announcements)To switch off the priority for traffic an-nouncements during a telephone call:Press TA during the telephone call.

5 TS / BNDTo switch from handset operation tothe hands-free function (uses the mi-crophone and car speakers):Press BND and replace handset.

1 On/OffThe set must be switched on before itis possible to use the telephone.VolumeAdjusts the volume while using the“hands-free” function.Adjusts the TA volume while using the“hands-free” function.Adjusts the volume of the current ringtone.

Remote control

The functions described under “Vol-ume” can be altered by pressing V- /V+.

2 / AUDIf this button is pressed while the tele-phone is in use, the microphone will bemuted. This makes it possible to con-duct a conversation in your vehiclewhile the party on the telephone is un-able to listen.

97

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

> Displays

Radio menu

a b

Enter PIN code

c

Network search ...

Basic telephone menu

Subscriber is called

de f

Telephone-book menu

g

Setup menu/Call menu

a) - Indicates connection to homenetwork

- Indicates that the Radio-phone has logged into a dif-ferent network.

If the antenna symbol isflashing, the telephone userhas not got access privilegesto the current network availa-ble. Only emergency callscan be placed.

b) - Indicates signal strength,shows how good the connec-tion to the radio network is

c) * - Appears when the code isentered. One asterisk ap-pears for each digit.

d) - Indicates that an SMS mes-sage has been stored

e) - Appears as an additional indi-cation that a voice messagehas been received

f) - Indicates that a telephonecall is being made or in theprocess of being placed

g) - Indicates that call forwardinghas been activated

; + / 0Enters the telephone number.To set the current foreign country codeautomatically, press 0 for longer than1 second.

<Switches to the telephone mode,answers/ends telephone calls,To start dialling:Press briefly.

To switch off the telephone, e.g. in are-as where there is danger of explosion:Press for approx. 2 seconds.

To switch back to the telephone mode:Press briefly.

= MIX/*Enters special characters, such asblank spaces.Activates speed-dialling for the num-bers stored on the SIM card.

98

? Anti-theft card protection systemIn order to be able to operate the tele-phone, you must insert a trained SIMcard first.Using a KeyCard, you can place anemergency call only.Using a trained SIM card, it is possibleto operate all of the telephone’s availa-ble functions, including the telephonemode.The SIM card also performs the anti-theft functions.

@ Rocker switch /

Scrolls through the speed-dial directo-ry in the telephone book.Selects the SMS entries.Selects the menu items in the tele-phone book and DSC menu.Moves the cursor to the next line whendata is being entered.

Remote control:

To select a telephone number from thespeed-dial list: Press ME first.

<< / >>Makes adjustments for the menu itemsin the telephone book and the DSCmenu.Displays SMS message.Allows you to scroll through entrieswhich require more space than availa-ble in the display.Moves the cursor to the left and rightwhen data is being entered.

A METo activate the telephone-book menu:Press ME briefly.

Remote control:

To display the telephone-book menu inalphabetical order: Press ME briefly.To display the telephone-book menu in

the numerical order of the entries:Press ME for approx. 2 seconds.To quit this function press CL on theset.

B CL (CLEAR)Entry mode

To delete the last digit entered: PressCL briefly.To delete the entry on display com-pletely, press CL for approx. 1 second.

Menu prompting:

To return to next higher level:Press CL briefly.To quit the menu:Press CL for longer than 1 second.

C OKTo activate setup menu , to activatecall menu :Press / briefly.

To activate a menu item:Press OK briefly.

To store settings: Press OK briefly.

To store altered parameters:Press OK briefly.

99

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Using the telephone

All of the telephone functions can be oper-ated using a trained SIM card.• With the card tongue protruding, insert

the trained SIM card into the slot withthe contact surface facing up .

• Switch the unit on.If you have not yet trained any SIM cards,refer to the section on “Train or delete Key-Card/SIM card”.

GSM network service area

To be able to use the telephone, you mustbe located in an area served by the GSMnetwork. As soon as a network signal is re-ceived, the symbol indicating the signalstrength and an antenna symbol willappear in the display. If the signal is notstrong enough your call may be disconnect-ed. If the antenna symbol is flashing, it ispossible to make emergency calls only. Ifthe antenna is displayed on a dark back-ground, you are located in an area servicedby a roaming network (may be subject toadditional charges).

Switching to telephone mode

It is possible to switch to the telephone modefrom any of the audio modes.• Press .

The display will indicate the network and thenetwork operator if a network signal is re-ceived. The antenna symbol will not flash.

Dialling a telephone number

The telephone mode must be switched on.

Always use the area code for the numberyou are dialling, even if it is a local number.

Manual

• Dial the number using the numberkeys.

The number you enter will appear in the dis-play.

Correcting the number

To delete a digit:• Select the digit you wish to correct us-

ing the rocker switch << / >> (digit willflash).

• Press CL briefly.

To delete a number:• Press CL for approx. 1 second.

To start dialling/end call:• Press .

100

Using speed-dialling . . .

You can recall stored telephone numberswith the corresponding name or the numberof the entry.

The numbers which can be recalled in thetelephone’s memory bank range from 1 to25, on the SIM card from 101 to a maximum225.

It is possible to use one-touch dialling forthe first nine telephone numbers in the ba-sic telephone menu by pressing the corre-sponding number key directly.

. . . directly from the memory bank:

• Press the corresponding button (1 to 9)for approx. 2 sec. until you hear abeep.

The call will be placed automatically.

. . . directly from the SIM card memorybank:

• Press * and the corresponding button(1 to 9) one after the other for approx.2 sec. until you hear a beep.

The call will be placed automatically.

. . . from the telephone book

• Press ME.

• Use / to select“Find entry by name” or“Find entry by position”.

• Confirm your selection by pressingOK.

If “Enter name” appears in the display• use the selection buttons to enter up to

the first three letters in the name.If “Enter position” appears in the display• use the selection buttons to enter the

position number of the entry.

• Confirm your entry by pressing OK.If you know the position number of the entryyou can enter it immediately after pressingME and confirm your selection by pressingOK.The desired telephone number will appearin the display.

If you want a different number to the oneshown in the display, you can press / toscroll through the entries in the telephonebook.

To start dialling/end call:• Press .

Redial function

Automatic

If the “Automatic redial” menu item in thesetup menu is switched to “ON”, the numberwill be redialled automatically.

Refer to “Programming with DSC – Setupmenu – Automatic redial”.

You can cancel the automatic redial bypressing the telephone key.

Manual

• Press .The last telephone number entered will ap-pear in the display.To start dialling:• Press .

The display will change in colour to indicatethat the telephone has begun to dial thenumber or that an incoming call has beendetected.

101

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Answering/ending a call

If someone calls you, you will hear the tele-phone ring and “Answer?” will appear in thedisplay. If you receive a call from a telephonesupporting call line identification (e.g. ISDN),the caller’s telephone number will appear inthe display.

If this number has been entered in thespeed-dial directory, the caller’s name willappear.

To answer a call:• Press one of the buttons on the right-

hand side of the set.To end a call:• Press or CL.

Call waiting (2nd caller)

While using the telephone you can receivea message that a second party is trying tocall you.

If you would like to take advantage of “callwaiting”, you may have to order this servicefrom your network operator and activate it.

How it works

You are still talking on the telephone to thefirst party. You hear the call waiting signal.

To refuse the call:• Press CL.To answer the waiting call:• Press OK.The first party will be put on hold (cannotjoin in on the second call).

Also refer to broker’s call/hold or conferencecalls.

Broker’s call/hold

During a telephone call, you can make orreceive a second call. The active call will beplaced on hold automatically.

During a broker’s call, you are able to talkto only one of these two parties at any onetime, while the second party is on hold.

Activating the hold function

The first call is currently active.• Enter the second telephone number

and start to dial by pressing .The first caller will be placed on hold andwill hear music.As soon as the second party answers, thesecond call will be active.

Broker’s call

Switches between the first and second call• Press ME.While you are talking on the telephone toone party, it is also possible to answer an-other call. You will hear the call waiting sig-nal.

To refuse the call:• Press CL.

To answer a call from a third party:• Press OK.

This will end the call with the party towhom you are currently talking.

To end an active call:• Press CL or .

To end both calls at once:• Press CL for longer than 1 second.

102

Conference calls

During a multi-party call, you can talk to sev-eral parties at the same time.

While talking to one party you can place acall to a second party.

Setting up a conference call

You are already talking to the first party. Asecond party is waiting on hold.• Press OK

to activate the conference call. Now allthree parties can talk to each other onthe same line.

While you are talking on the telephone tothese two parties, it is also possible to an-swer a call from another party. You will hearthe call waiting signal.

To refuse the call:• Press CL.

To answer a call from another party:• Press OK.

The previous parties will be put onhold.

Press ME to switch back and forth betweenthe conference call and the single caller.

To end an active call:• Press CL or .

To end all calls at once:• Press CL for longer than 1 second.

Making telephone calls usingthe handset (special accessory)

During normal operation, you can make tele-phone calls using the microphone and carspeakers (hands-free function). You canalso make calls using a handset (accesso-ry).

You can answer/end calls by removing/re-placing the handset.

Switching from hands-free operation to thehandset:• Remove the handset from its cradle.

To switch from handset operation to thehands-free function:• Press BND and replace the handset

on its cradle.

Warning:

There is a relatively strong magnet built intothe handset.

Keep away anything which will react to mag-netic influence, e.g. diskettes, bank cards,etc. Important data may be deleted.

103

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

ME

^

Return to phone book (from any menu item): Press CL

^^

^^

^^

^^

^^CL

SRC

^^

Phone Book Menu

Start

^

Phone book menu

The phone book menu can be used to store,alter, delete and easily retrieve stored tele-phone numbers.

The entries are stored in the telephonememory and/or on the SIM card and can beused for speed-dialling.

The telephone can store up to 25 entries.

The number of entries which can be storedon the SIM card depend on the type of cardused.

Access the phone book menu as follows:• Press ME on the set.“Phone book” will appear in the display.

Press / to select the menu items whichare described in the following.• Select the function and press OK.Press CL to exit the current menu item andreturn to the phone book menu.

Press CL once again to display the basictelephone menu.

If you press ME briefly on the remote con-trol, you will access an alphabetically sort-ed speed-dial directory of telephone num-bers directly.

If you press ME for somewhat longer on theremote control, you will access the speed-dial directory sorted numerically accordingto the entry position.

104

How to enter a name/text

Using the keypad you can enter names ortexts for various menu items.

You cannot make an entry unless a specificrequest that you do so appears in the dis-play.

Names can have a maximum of 16 and texts160 characters.

Start the entry

If “Name?” appears in the display,• press the key for the first character as

often as necessary.For a new name enter all of the letters forthe name.

Entering letters/characters

Example “O” = press key 6 three times.

The keys are sequence keys, i.e. press thekeys repeatedly to call up the letters allo-cated to this key.

You can use these keys to enter the follow-ing characters:

1 _ (blank) . , ! ? : ’ " ( ) % & 1

2 A B C Ä à 2

3 D E F É 3

4 G H I ì 4

5 J K L 5

6 M N O Ñ ö ò 6

7 P Q R S ß 7

8 T U V ü ù 8

9 W X Y Z 9

0 + - x * / = < > # 0

Capital and small letters

You can choose between capital and smallletters.

To switch:• Press the key for the letter you wish to

select for approx. 1 second.All of the following letters will appear in theformat selected.

Switch back if desired.

Moving the cursor in the entry text box

If you press different keys to enter the let-ters one after the other, the flashing cursorwill automatically move forward .

If you have to press the same key to enterdifferent letters you must first move the cur-sor by pressing >>.

To make any necessary corrections movethe cursor by pressing << / >>.

Inserting characters

You can insert characters as follows:• Select the position for the new letter by

pressing << / >>. The character will beinserted in front of the flashing cursor.

• Press the key for the character youwish to insert.

Deleting characters

You can delete individual characters or acomplete entry.

To delete characters:• Press << / >> to select the character

you wish to delete (it will flash).• Press CL briefly.

To delete an entry:• Press CL for approx. 1 second.

105

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Finding an entry by name

Selecting an entry:

• Press / to select “Find entry byname” and press OK.

• Enter the first three letters of the nameand press OK.

A name with these first three letters or theclosest name alphabetically in the list willappear in the display with the correspond-ing telephone number.

Important: The memory bank must alreadycontain at least one entry.

If necessary, press / to scroll through thelist of entries forwards/backwards until youhave found the name (and telephonenumber). Press << / >> to view all of the datastored for the entry.

To dial the telephone number automatical-ly:• Press .

Selecting an entry by remote control:

Using the remote control you can activatethe alphabetically or numerically sortedspeed-dial directory in the telephone bookdirectly.

For the alphabetically sorted list:• Press ME briefly.For the numerically sorted list:• Press ME for somewhat longer.To scroll through the lists:• Press / .To dial the telephone number automatical-ly:• Press .

Changing, deleting, moving or copyingan entry

• Find the name/entry as describedabove.

• Press OK, “Change?” will appear inthe display.

• Select the function you wish to use bypressing / and the press OK.

To change:

You can alter the name and telephonenumber one after the other.

To delete:

• Press OK to confirm, CL to abort.

To move:

You can move the entries to a different po-sition in the list.

The arrow indicates the current position.

• Press / to select the new positionand press OK.

To copy:

You can copy entries from the SIM card, forexample, into the telephone memory bank.

The arrow indicates the current position, e.g.210.• Press / to select the new position,

e.g. 023, and press OK.

106

Show my phone number

You can display your own telephone numberif it has been stored.• Press / to select “Show my phone

number” and press OK.If more than one number appears, press

/ to select the correct one.

Prevent access

You can prevent unauthorised persons fromaccessing the telephone memory bank. Ifdesired• Press / to select “Prevent access”

and press OK.

• Press / to choose among the fol-lowing settings:

“No memory restriction”– All access restrictions are deacti-

vated.“Lock SIM card”

– It is not possible to access the tele-phone numbers stored on the SIMcard.

“Lock phone”– It is not possible to access the tele-

phone numbers stored in the tele-phone memory bank.

“No access possible”– It is not possible to access the tele-

phone numbers stored in the tele-phone memory bank or on the SIMcard. It is not possible to store newtelephone numbers.

• Confirm your selection by pressingOK.

• Enter the access code and press OK.

• Press << / >> to select on or off andpress OK.

Check capacity

Use this function to determine how muchstorage capacity is available on the SIM cardand in the telephone memory bank.

• Press / to select “Check capacity”and press OK.

• Press / to select “Check SIM ca-pacity” or “Check phone capacity” andpress OK.

The number of free entries available will ap-pear in the display.

If there are no entries available, “memoryfree” will appear in the display.

107

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Add entry

You can store up to 25 telephone numbersand names in the telephone memory bank.

The number of entries you can store on theSIM card depends on the type of card youuse.

If you would like to add or alter (overwrite)an entry, press the following keys one afterthe other:

• Press / to select “Add entry” andpress OK.

• Press / to choose the entry posi-tion, for example:“SIM card 101-255” or“Phone book 1-25” and press OK.

• Enter the new telephone number andpress OK.

• Use the selection buttons to enter thename and press OK.

• Enter the position number and pressOK.

If you do not enter a position in the memorybank, the next available position will be se-lected.

If there is a number already stored at theposition entered, “Overwrite?” will appear inthe display.

Press OK to overwrite the entry (the previ-ous entry will be deleted).

Add the next entry:• Press OK.

Finding an entry by position

You can use the position number to find,alter, delete, move or copy the entry in thetelephone book.

Selecting an entry:

• Press / to select “Find entry by po-sition” and press OK.

“Enter position!” will appear in the display.

• Use the selection buttons to enter theposition number and press OK.

The position number, the name entered andthe telephone number will appear in the dis-play.

To dial the telephone number automatical-ly:• Press .

Altering, deleting, moving or copying theentry:

If necessary, proceed as described in thesection on “Finding an entry by name”.

108

Programming with DSC Telephone

Thanks to DSC (Direct Software Control), itis possible to adapt several of the Radio-phone settings and functions to your ownpersonal needs and to store these altera-tions.

The Radiophone has been set at the facto-ry.

In the following you will find an overview ofthe default settings, so that you can resetthe unit to these basic settings if necessary.

If you wish to alter the programming:• First select the operating mode, e.g.

telephone mode, if you would like toalter the volume for hands-free opera-tion.

Access the DSC menu• by pressing DSC/OK briefly.

Select:

Use the rocker switch / to select themenu item you wish to alter and press OKto confirm your selection.

Alter:

Press << / >> to alter the setting shown inthe display and confirm your change bypressing OK.

Cancel:• Press CL, the altered setting will not

be stored.

Store/confirm:• Press OK.

End DSC:• Press CL.

109

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Programming in the setup menu

• Select the setup menu by pressing .

DSC

^

^^

^

^^

^^

^^

^^

^^

Setup Menu

Start

Return to setup menu/call menu(from any menu item):Press CL

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

^^

Off

^̂^ ^̂^CL

SRC

^̂^

On

*

* Alternately:

110

Ringing tone volume

Press << / >> to adjust the volume of theringing tone from between 0 and 9. 0 = off.

If the automatic answer function is switchedon, the volume cannot be set to “0”.

Hands-free volume

Press << / >> to adjust the volume of theincoming call from 0 to 63 over the carspeakers.

Handset volume

This menu item will not appear unless aBlaupunkt handset has been connected tothe system.

Press << / >> to adjust the volume of thehandset to one of three levels (low, medi-um, high), remove the handset from the cra-dle first.

Automatic answer

The telephone will automatically answer in-coming calls if you press << / >> to select“On” for this menu item.

The call will be set to hands-free operationautomatically.

In this case, do not set the ringing tone vol-ume to “0”.

Automatic redial

If the busy signal is received, an outgoingcall will be redialled automatically if youpress << / >> to select “On” for this menuitem.

You can stop the automatic redial by press-ing the telephone button.

Off – redial is switched off

On – redial is switched on.

The number of times the telephone will at-tempt to redial depends on the networkused.

Operating mode

If this menu item is selected, you will be re-quired to enter the access code after press-ing OK.

Then select the operating mode by press-ing << / >>:

Standard – all operating modes

Radio only – no telephone, all otheroperating modes

Phone only – telephone mode only

Extended menu

Use this function to remove the followingmenu items from the display in the setupmenu by pressing << / >>. These items areseldom used.

This makes the setup menu more clear.

Off – menu items removed from display

On – all of the menu items are available.

111

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Ringing tone

You can select the ringing tone by pressing<< / >> to choose from “Standard, Smooth,Rising (ringing tone gets louder with eachring), Off”.

“Off” corresponds to “Ringing tone volume0”.

SMS tone

If a message has been received by SMS orvoice mail, the equipment can be set to emita beep at a preset beep volume.

Off – beep is emitted after a messagehas been received

On – beep is switched off.

My phone number

Here you can enter a maximum of up tothree of your own telephone numbers andthe telephone number for your mailbox.

The mailbox number is required to be ableto call it directly from the call menu.

After you press OK “Number 1” will appearin the display.

Press / to select the position for your ownphone number.

Press OK and enter your own phone numberand press OK again. The display shows“Number stored”.

Press / to select the next position, etc.

Call meter format

You can select whether the call charges orthe call time is displayed during a call.

AOC parameters (Advice of Charge)

This function depends on the features theSIM card includes.

If AOC is not supported by the card, “Setcharge parameters” will appear as a menuitem in its place.

The charge rates are determined by thenetwork operator.

You can use this menu item to set the charg-es and a credit balance. As soon as the cred-it balance has been exhausted, it will not bepossible to use the telephone until the cred-it balance is replenished by an authorisedperson.

If your network operator does not supportAOC, the time interval will be set to oneminute. The value selected will be used formaking calculations. The credit function isdeactivated.

If this menu item is selected, you will be re-quired to enter the “PIN2 code” or the “Ac-cess code” after pressing OK.

112

After this, you can enter a charge per unitand a credit balance.

If a charge or credit balance has alreadybeen entered, the last character will flash inthe display.

Use the numbers keys to alter the amountand the type of currency.

Press CL to quit the menu item.

The alteration will be transferred to the SIMcard.

Note:

If “0.00” appears in the display, the creditbalance function is deactivated.

Set charge parameters

If you cannot use AOC, you can set an in-ternal charge counter. You can enter thecharge per minute.• Press OK.

• Enter the access code.

• Press OK.

• Select home or roaming networkcharge by pressing / and pressOK.

• Enter the charge and type of currencywith the numbers keys.

• Confirm your entry by pressing OK.

Note on AOC/charge parameters

Because the charges per time unit may vary,the charge meter can be used only as anapproximate point of reference.

Audible call timer

You can set an audible beep which is emit-ted after a preset call time has elapsed.

Press << / >> to switch the beep on or off.

You can use the selection buttons to alterthe setting from between 15 and 300 sec-onds. The cursor will flash at the last digit ofthe value entered.

After you have pressed OK, “Audible calltimer” will appear in the display. You canselect the next menu item.

PIN code

Switches on/off and alters the PIN code.

Press << / >> to switch between On, Alter,Off. An arrow will indicate the setting select-ed last.

If you wish to alter the setting, press OK.Enter the PIN code and press OK to con-firm your entry.

On – Each time the SIM card is in-serted, the PIN code must beentered.

IMPORTANT!If the PIN code is entered incorrectly threetimes in succession, the SIM card will bedeactivated. It can only be reactivated afterthe master PIN (PUK) has been entered.Your service provider has more detailed in-formation.

Alter – You must enter the currentlyvalid PIN code, then enter thenew PIN code (twice)

Off – The set can be operated with-out a PIN code.

The “Off” menu item cannot be selectedunless the SIM card allows this.

113

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Alter access code

Use the access code to gain access to theimportant menu items.

This code is set to “0000” at the factory.

Be sure to make a note of the new codeif you change it.

Enter the old code (in this case “0000”) andpress OK.

Enter the new code, press OK. Enter thenew code again and press OK again.

Master clear

Using this menu item you can delete thetelephone settings.

You can also delete the SIM card settings.

Please be careful when using this function!

External alarm

If the ignition is switched off, you can havean incoming call signalled by the car’s hornor flashing lights in addition to the ringing inthe car.

For this to operate, you must first

press << / >> to switch the function“External alarm” to ON in the DSCmenu.

Switch off the unit with the ignition andswitch it on again by pressing the ONbutton.

If an incoming call is detected, the externalalarm will sound five times in succession.

To protect the vehicle’s battery power, theunit will switch off automatically after onehour.

If necessary you can switch on the externalalarm again for one hour by pressing theON button.

Refer to the installation instructions for con-nections and accessories.

The following settings will be deleted:a) Phone

Speed-dial directoryCall charges settingCall counter

b) SIM cardSpeed-dial directoryRedial memoryOwn phone numbersMailbox numbersSMS messagesAOCFixed telephone numbersPreferred networksPreferred language.

If this menu item is selected, you will be re-quired to enter the access code after press-ing OK. Enter the access code, press OK.

Then select “Card” or “Phone” by pressing<< / >>.

“Clear phone memory?” or “Clear card?” willappear in the display.

Press CL if you want to cancel the process.

Do not press OK unless you want to do a“Master clear”, “cleared” will appear in thedisplay.

The process has been completed when“Master clear” appears in the display.

114

TA during call

It is possible to have a traffic announcement(TA) broadcast while you are using the tele-phone.

Press OK to view the setting already select-ed.

Off – TA is switched off during a call

On – TA is switched on.

Select the setting desired by pressing<< / >>.Confirm by pressing OK.

Quit the menu

Press CL to return to the previous menu. Ifnecessary,• press CL as often as required.

Important!It is against the law to activate the audibleexternal alarm in Germany.Find out what the regulations are regardingthis in your own country.

Hands-free channel

Hands-free operation is possible on all fourchannels.

If a traffic announcement is broadcast (TAon), you can select which channel (left/right)will remain active for hands-free operation.

Press OK to view the setting already select-ed.

Make any alterations by pressing << / >>,press OK.

Quit this menu item by pressing CL.

Overview of the basic factorysettings in the set-up menu

Ring volume 4Hands-free volume 35Handset volume MediumAutomatic answer OffAutomatic redial OffOperating mode StandardExtended menu OnRing signal StandardMessage signal OnCall meter Time displayAcoustic check OffAlter access code 0000External alarm OffHands-free channel LeftTA during call On

115

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Programming in the Call Menu

If you would like to alter the programming,select the telephone mode first:• Press and access the DSC menu

by

• pressing DSC/OK briefly.

• Select the call menu by pressing .

Now you can proceed with your alterations.

Select:

Use the rocker switch / to select themenu item you wish to alter and confirm yourselection by pressing OK.

Alter:

Press << / >> to alter the setting shown inthe display and confirm by pressing OK.

Cancel:

• Press CL, the new setting will not bestored.

Store/confirm:

• Press OK.

DSC

^^

^^^^

^^

Call Menu

Start

To retrieve the messages in your mailbox:Select “Call mailbox” and press CL

^^

^^^^

^^

^̂^ ^̂^

^

CL

SRC

^^

116

Call mailbox

The mailbox (also known as the mobile box)is comparable to an answering machine.You can also enter your own message texthere. The texts stored in the mailbox aresorted into new and old messages and canbe retrieved at any time.

Before you set up your mailbox, contact yournetwork operator/service provider to obtainthe telephone number and other mailboxinformation. You can also call your mailboxfrom a regular telephone.

To make the best use of your mailbox, it is agood idea to activate call forwarding to yourmailbox telephone number in the call menu.If no number has been stored, you will berequested to enter one when you activatethe mailbox function.

To retrieve your messages:• Select “Call mailbox” and press OK.The unit will call the mailbox automatically.You will receive all of the necessary infor-mation on how to proceed.

An “N” as the first letter means that the mes-sage is new.

If nothing appears in this position, then themessage has been read and stored.

The individual messages are sorted accord-ing to date and time. The telephone numberand the name of the caller will appear in thesecond line.

Reading messages

• Press OK,you can display the message by press-ing << / >>.

Clearing messages

To clear a message:• Press CL.“Clear message?” will appear in the display.

Press OK to clear the message, press CLto abort this function.

Received SMS messages

You can receive individual text messagesof up to 160 characters in length which oth-er subscribers send to your telephonenumber via SMS.

You can read and file the messages youreceive in the menu “Received SMS mes-sages”.

When a message is received, the telephonewill try to store it on the SIM card. As soonas the storage capacity on the SIM card hasbeen exhausted, the symbol will flash inthe display.

One or more messages must be deletedbefore new messages can be received.

Selecting the message

• Select “Received SMS messages” andpress OK.

The display will indicate the number of “New”and “Old” messages.

“Old” means that the message has beenread and stored.• Press OK.Press / to select the messages.

117

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Calling the sender or another telephone

If you would like to call whoever sent themessage,• press while the message is on dis-

play.The telephone will automatically call thecorresponding number. If the message con-tains a telephone number in “quotationmarks”, the call will be made to that number.If there are several different telephone num-bers in quotation marks, the call will be madeto the first one.

Sending SMS messages

Using this menu item you can send mes-sages to other subscribers and set the cor-responding parameters.

• Press / to select “Send SMS mes-sage” and press OK.

• Press / to select the desired func-tion and press OK.

“SMS parameters”

• Press / to select the desired func-tion and press OK.

“Valid”:Here you can determine how long thenetwork operator should continue try-ing to send the message. The defaultsetting is 1 day. Use the numbers keysto select from 1 to 7.After making your selection• press OK.

“Service no.”:The message is sent to a servicenumber provided by the network oper-ator and forwarded from there to therecipient. Contact your network opera-tor to receive the service number andenter it here.

Service no.:

“New SMS message”

• Press OK, “Enter text” will appear inthe display.You can now enter a text of up to 160characters. If necessary, please referto the section on “How to enter aname/text”.

• Press OK after you have enteredthe text.

“Call number” will appear in the dis-play.

• Enter the recipient’s telephonenumber and press OK.

“Store?” will appear in the display.

• Press / to select “Send?”, “De-lete?” or “Store?” and press OK.

Sending “Stored SMS messages”

• Press / to select the desired func-tion and press OK.

“My short messages”The beginning of the message will ap-pear In the first line of the display, thetelephone number of the recipient inthe second line.“Received messages”The display will indicate the date, timeand sender.

118

To select, alter, send message.

Press / to select a message. Afteryou press OK, two lines of the mes-sage will appear in the display.

Press << / >> to read the text andmake any alterations if required.

• Press OK.“Store?” will appear in the display.

• Press / to select “Send?”, “De-lete?” or “Store?” and press OK.

Network selection

In areas which are served by more than onenetwork (e.g. in foreign countries), it is pos-sible to select the network you wish to use.• Press / to select “Network selec-

tion” and press OK.

• Press / to select from the availablenetworks and press OK.

“Available networks”

– After a short waiting period, the availa-ble networks will appear in the display.

The first line indicates the positionnumber, * and network operator code.The second line displays the name ofthe network operator.

* means that the SIM card currently inuse will operate the telephone to makecalls in this network.

Press / to select other networksand press OK to confirm your selec-tion. “Register now?” will appear in thedisplay. Abort by pressing CL, confirmby pressing OK.

“Search method”

– It is possible to select an automatic ormanual search (for network selection).

Automatic search:The home network is always the firstchoice. If you are located in an areawhich is not served by your home net-work, the telephone will automaticallyregister with the next available net-work. The networks will be selectedaccording to their priority in the net-works list.

Manual search:The sorted list of network operatorswill be displayed in this mode.Switch to the search mode by pressing<< / >>, confirm by pressing OK.An arrow will indicate the current con-dition.

The antenna symbol indicates whichnetwork the telephone is registered in.

– Connected to home network

– Connected to a different network

If the antenna symbol is flashing, youdo not have access privileges to thenetwork currently connected. You canplace emergency calls only.

119

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

“Preferred networks”

– Use this menu item to alter the priorityin the list of preferred network opera-tors.

• Press / to make your selectionand press OK:

“Add network to list”:– known networks

Press / to select the desirednetwork from the list of network op-erators, press OK. Give the net-work most important to you priority1. Select other networks of interestto you and determine their se-quence.

– new networkYou can add a new network opera-tor to your preferred list (you willrequire the operator’s networkcode).

“Show list of networks”:

You can display the list of networks bypressing / .Quit by pressing OK.

“Delete entry”:

You can delete any network operatorsyou do not require from the list.

• Confirm your selection (“Delete en-try”) by pressing OK.The display will indicate the posi-tion in the priority list, the networkcode and the name of the operator.

• Press / to select the networkoperator you wish to delete andpress OK.

“Delete?” will appear in the display.

Press OK to delete the network opera-tor from the list, press CL to cancel theprocess.

“Move entry”:

You can move any of the entries in thepriority list (new sequence).

• Confirm your selection (“Move en-try”) by pressing OK.

The display will indicate the position inthe priority list, the network code andthe name of the operator. If you wantto move an entry to another position,

• press OK.

“Priority?” will appear in the display.

• Now enter the number of the newposition by pressing the corre-sponding selection buttons andpress OK.

Cell Broadcast

Cell Broadcast is a short message servicewhich operates in numbered “channels”.

The channels transmit different special mes-sages.

Request more detailed information and a listof the available channels from your networkoperator.

If Broadcast “On” has been selected, thenumber of the channel on which you expectto receive information must be entered af-ter you have pressed OK.

120

Call meters

The telephone is equipped with an internalmeter which allows you to display the charg-es or call time for individual calls and thenumber of total calls.

The default setting displays the call time.• Press / to select “Call meters” and

press OK.

• Press / to make your selection andpress OK:

“Show meter - last call”– Time or charge for the last call

“Show meter - all calls”– Total call time or charges

“Show meter - roam calls”– Time or charges for all calls made in a

roaming network

“Show meter - home calls”– Time or charges for all calls made in

the home network

“Reset call meters”– Sets time or charges to zero

“Show meter during call”– Switch display of call meter during

calls on/off

Note

If the SIM card supports AOC, the menuitems for “Show meter - roam calls” and“Show meter - home calls” will not appear.

Call forwarding

You can forward incoming calls to anothernumber. For this to operate the call forward-ing function must be activated.If necessary,• press / to select “Call forwarding”

and press OK.

• Press / to make your selection andpress OK:

“Forward all calls”– Every call will be forwarded immediate-

ly.

“Forward, if busy”– The call will not be forwarded unless

the line is busy.

“Forward, if no answer”– The call will be forwarded if you do not

answer it.

“Forward, if unreachable”– The call will be forwarded if the Radio-

phone is switched off or you are not lo-cated in an area serviced by GSM.

“Clear all”– All call forwarding functions will be de-

activated.

Call barring

You can block incoming/outgoing calls orforward them to another number. Select thetype of call forwarding you wish to use inthe menu.• Press / to select “Call barring” and

press OK.

• Press / to make your selectionfrom “Bar outgoing calls”, “Bar incom-ing calls” and “Change password” andpress OK.

121

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Bar outgoing calls:

• Press / to make your selectionfrom the menu items and press OK:

”International"– No calls can be made outside of

the country.

“Internation. except home”– No calls can be made outside of

the country.If you are in a foreign country, youcan place calls to your home coun-try.

“all calls”– You cannot make any calls. It is

still possible to make emergencycalls.

“no barring”– All restrictions on outgoing calls

have been removed.

Bar incoming calls:

• Press / to make your selectionfrom the menu items and press OK:

”By roaming"– If you are in a foreign country, you

cannot receive any calls.

“Bar all”– You cannot receive any calls.

“No barring”– All restrictions on incoming calls

have been removed.

Change password:

– You can alter the password required tooperate network barring.

Phone lock

You can prevent your telephone from beingused by unauthorised persons. If necessary,• Press / to select “Phone lock” and

press OK.

• Press / to make your selectionfrom the menu items:

“No restriction”– All restrictions are removed.

“Dialling not possible”– Only emergency calls can be made.

“One-touch dial only”– You can only call the one-touch dial-

ling telephone numbers stored on keys1 to 9 and the SIM card.

“Speed/touch dial only”– All of the telephone numbers stored (in

the phone and on the SIM card) can bedialled.

• Confirm your selection by pressingOK.

• Enter your access code and pressOK.

• Press << / >> to switch the functionon/off and press OK.

Fixed dial numbers

This menu item will not appear unless theSIM card supports it.

You can limit the use of the telephone tocertain numbers (fixed phone numbers). Youcan store these on the SIM card.• Press / to select “Fixed dial num-

bers” and press OK.

• Press / to make your selectionfrom the menu items:

122

“Edit list fix dial no.”– The list of telephone numbers entered

will be displayed.

“New entry fix dial no.”– You can add a new phone number to

the fixed numbers list.

“Activated”– Switch this function on/off.

Closed user group

This is a special feature which you can or-der from your network operator.

Using it, it is possible to limit the use of thetelephone to a certain group of users.

Important!

Do not alter any of these settings unless thisfunction has been activated by your networkoperator. Otherwise, this could cause mal-functioning.

Overview of the basic factorysettings in the call menu

Send messageService number ---

Call meterLast call 0,00 DMDisplay during call On

Telephone block No restrictions

123

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Glossary

Access code

Barred functions can be operated after theaccess code is entered.

AOC parameter - Advice of Charge

List of charges in which a charge per unitand a credit balance can be entered.

Broker’s call

It is possible to make a second call withoutending the first one. You can then switchfrom one call to the other.You can also answer a call from a secondparty without ending the call to the first.

Cell Broadcast

Cell Broadcast is a short message servicewhich operates in numbered “channels”.The channels transmit different special mes-sages.Request more detailed information and a listof the available channels from your networkoperator.

GSM network - Global System for MobileCommunication

European cellular telephone standard avail-able world-wide.

IMEI - International Mobile EquipmentIdentity

International identity for mobile equipment.The IMEI code entered at the factory in-cludes the serial number, manufacturer andcountry code. You can find this code in thecar radio pass.

Mailbox

Electronic mailbox provided by network op-erators for spoken messages. The mailboxcan be compared to an answering machine.

MUTE

Switches audio off

PIN code - Personal Identification Number

PIN 1Protects the SIM card from being used byunauthorised persons. You must enter thePIN code each time the card is inserted intothe unit.

PIN 2Code for special functions.If you are entitled to use special functionswith your card, you need a PIN 2 code.Both codes are supplied with the SIM cardand can be altered if desired.

PUK - Personal unblock code

Eight-digit unblock code which can reacti-vate the SIM card. This becomes necessaryif the PIN code for the SIM card has beenentered incorrectly three times.

Roaming

Making telephone calls in foreign countrieswith your own telephone or your own SIMcard using a different network operator.

Scrollen

Moves you through a directory.

SIM card - Subscriber IdentificationModule

In credit-card format.The SIM card contains all of the data re-quired to identify the subscriber, to allocatethe telephone number and the personalphone book.Using your SIM card it is also possible tomake telephone calls with a cellular phone.

124

SMS - Short Message Service

Using this function it is possible to send othersubscribers messages up to 160 charactersin length, even if the recipient’s cellularphone is not switched on or a call cannot beput through at the present time.The text is stored temporarily in the networkuntil the recipient retrieves his messages orthe time limit set by the sender has expired.

Specifications

AmplifierOutput power: 4 x 23 watts RMS

according toDIN 45 324 at 14.4 V4 x 35 watts maxi-mum power

TunerWavebands:FM 87.5 – 108 MHzMW 531 – 1602 kHzLW 153 – 279 kHz

FM sensitivity: 0.9 µV at 26 dBS/N ratio

FM transmission range:30 - 16,000 Hz

Tape deckTransmissionrange: 30 - 18,000 Hz

Telephone

Standard: GSM

Frequency band:Send 890 – 915 MHzReceive 935 – 960 MHz

Transmission power: Class 4 / 2 watts

Sensitivity: -108 dBm

Impedance:Antenna connection 50 ohmsHands-free microphone 660 ohms

Subject to modifications!

125

DE

UT

SC

HR

adio

Tel

efon

EN

GLI

SH

Rad

ioT

elep

hone

Blaupunkttelephone help line

Address of the next servicecentre in your vicinity(only for Germany)

If you would like to know the address ofthe next Blaupunkt service centre ofyour area but haven’t got our servicelist at hand:- Find out your area code.

- Then call the following phonenumber (subject to charges):01 80 / 5 25 56 66.

- Using the area code you enter thisservice will automatically provideyou with the address and phonenumber of the Blaupunkt servicecentre nearest to you. You canalso request this information byfax.

Blaupunkt-Werke GmbHBosch Gruppe

07/98 Pf K7/VKD 8 622 400 962 0188