ALTEC Augers

Presents

1-877-GO ALTECCall Toll Free

9002-00017 09/05

Augers & Auger Accessories

http://www.altec.com


2

All Auger Assemblies have 24-48 Hour Availability

P/N 700-90096 & P/N 700-90095 and a P/N 9000-37350 “Fish Tail” pilot bit.

P/N 700-90063 & P/N 700-90091, and a pilot bit P/N 700-90177

Description 2 1/2” hex hub 2 5/8” hex hub

8” diameter P/N 700-90049 P/N 9000-11575

9” diameter P/N 700-90050 P/N 700-90079

10” diameter P/N 700-90051 P/N 700-90080

12” diameter P/N 700-90052 P/N 700-90081

14” diameter P/N 700-90053 P/N 700-90082

16” diameter P/N 700-90054 P/N 700-90083

18” diameter P/N 700-90055 P/N 700-90084

20” diameter P/N 700-90056 P/N 700-90085

22” diameter P/N 700-90057 P/N 700-90086

Utility Dirt Augers with 2-1/2” and 2-5/8” hex hubs, overall length of 104” with 60” of flight, standard teethP/N 700-90096 & P/N 700-90095 and a P/N 9000-37350 “Fish Tail” pilot bit.


24” diameter P/N 700-90058 P/N 700-90087

27” diameter P/N 700-90225 P/N 9000-11576

28” diameter P/N 700-90237 P/N 9000-11577

30” diameter P/N 700-90094 P/N 9000-11578

36” diameter P/N 700-90118 P/N 9000-11579

Utility Carbide Augerwith 700-90177 “Fish Tail” Carbide Bit

Utility Carbide Augers 2-1/2” and 2 5/8” hex hubs, overall length of 104” and 60” of flight, carbide teeth P/N 700-90063 & P/N 700-90091, and a pilot bit P/N 700-90177


8” diameter P/N 700-90182 P/N 9000-54560

9” diameter P/N 700-90183 P/N 700-90198

10” diameter P/N 700-90184 P/N 700-90194

12” diameter P/N 700-90185 P/N 9000-54563

14” diameter P/N 700-90186 P/N 9000-54564

16” diameter P/N 700-90187 P/N 700-90195

18” diameter P/N 700-90188 P/N 9000-54566

20” diameter P/N 700-90189 P/N 700-90196

22” diameter P/N 700-90190 P/N 700-90205

24” diameter P/N 700-90191 P/N 700-90197

30” diameter P/N 700-90192 P/N 9000-54570

36” diameter P/N 700-90193 P/N 9000-54571

Utility Dirt Auger with 700-90061 pilot

Digger Derrick Utility - Carbide Augers

Digger Derrick Utility - Dirt Augers

3



8” diameter P/N 9000-54600 P/N 9000-54620

9” diameter P/N 9000-54601 P/N 9000-54621

10” diameter P/N 9000-54602 P/N 9000-54622

12” diameter P/N 9000-54603 P/N 9000-54623

14” diameter P/N 9000-54604 P/N 9000-54624

16” diameter P/N 9000-54605 P/N 9000-54625

18” diameter P/N 9000-54606 P/N 9000-54626

20” diameter P/N 9000-54607 P/N 9000-54627

22” diameter P/N 9000-54608 P/N 9000-54628

24” diameter P/N 9000-54609 P/N 9000-54629

30” diameter P/N 9000-54610 P/N 9000-54630

36” diameter P/N 9000-54611 P/N 9000-54631

P/N 700-90091, P/N 700-90095, and P/N 0700-90061

Utility Carbide Augers 2 1/2” and 2 5/8” hex hubs, overall length of 104” with 60” of flight, carbide teeth P/N 700-90063 & P/N 700-90091 and a P/N 8994-08330 pilot bit.

Utility Carbide Auger with 700-09002 Carbide Tipped Pilot

Utility Carbide Augers, 2 1/2” and 2 5/8” hex hubs, overall length of 104” with 60” of flight, carbide teeth P/N 700-90063 and P/N 700-90091 and a P/N 700-09002 pilot bit .


16” diameter P/N 9000-54410 P/N 9000-54415

18” diameter P/N 9000-54411 P/N 9000-54416

20” diameter P/N 9000-54412 P/N 9000-54417

24” diameter P/N 9000-54413 P/N 9000-54418

Utility Carbide Augerwith 8994-08330 pilot bit

P/N’s 700-90063, 700-90091, and 700-09002

Digger Derrick Utility - Carbide Augers, cont.


4



9” diameter P/N 9000-33600 P/N 9000-25809

10” diameter P/N 9700-40560 P/N 9700-40561

12” diameter P/N 9000-33601 P/N 9000-25812

14” diameter P/N 9700-40563 P/N 9700-40564

16” diameter P/N 9000-33602 P/N 9000-25816

18” diameter P/N 9000-33603 P/N 9000-25818

20” diameter P/N 9000-33604 P/N 9000-25820

22” diameter P/N 9700-40565 P/N 9700-40566

24” diameter P/N 7017-05033 P/N 9000-25824

30” diameter P/N 9000-33606 P/N 9000-25830

36” diameter P/N 9700-40568 P/N 9700-40569

These step rock augers are best utilized in solid non-frac-turable rock. They have an overall length 104” and a 60” flight.

These augers designed, for solid rock, fracturable rock, and compacted soils, maximize drilling for all types of digger derricks. The augers have an overall lenght of 104”, with 60” of flight and are made with a heavy bottom flighting and standard pilot bit P/N 9000-32191 (2-38” API)


9” diameter P/N 9000-54330 P/N 9000-09258

10” diameter P/N 9000-54331 P/N 9000-10258

12” diameter P/N 9000-54332 P/N 9000-12258

14” diameter P/N 9000-54333 P/N 9000-14258

16” diameter P/N 0700-90206 P/N 9000-16258

18” diameter P/N 9000-54335 P/N 9000-18258

20” diameter P/N 9000-54321 P/N 9000-20258

22” diameter P/N 9000-11580 P/N 9000-11581

24” diameter P/N 9000-54322 P/N 9000-24258

30” diameter P/N 9000-54338 P/N 9000-30258

36” diameter P/N 9000-54339 P/N 9000-36258

Bullet Tooth Augers

Step Rock Augers

Digger Derrick Utility - Step Rock Augers

Digger Derrick Utility - Bullet Augers

5


Fast Change Utility Dirt Auger HeadsThe Fast Change utility dirt auger head comes with standard dirt teeth. Best used in compacted soils, soft shales & clay.

Description Part #

8” boring head P/N 9000-56500














Description 2 1/2” hex hub 2 5/8” hex hub8” flight body P/N 9000-56575 P/N 9000-565769” flight body P/N 9000-56580 P/N 9000-5658110” flight body P/N 9000-56585 P/N 9000-5658612” flight body P/N 9000-56595 P/N 9000-5659614” flight body P/N 9000-56600 P/N 9000-5660116” flight body P/N 9000-56605 P/N 9000-5660618” flight body P/N 9000-56610 P/N 9000-5661120” flight body P/N 9000-56615 P/N 9000-5661622” flight body P/N 9000-56620 P/N 9000-5662124” flight body P/N 9000-56625 P/N 9000-5662626” flight body P/N 9000-56630 P/N 9000-5663127” flight body P/N 9000-56635 P/N 9000-5663630” flight body P/N 9000-56640 P/N 9000-5664136” flight body P/N 9000-56645 P/N 9000-56646

Fast Change flight bodies have an overall length of 104 inches with 60” of flight. These flight bodies are available with 2-1/2” or 2-5/8” hex hubs.

Fast Change - Flight BodiesDigger derrick auger Fast Change systems give crews the ability to switch cutter heads when dynamic drilling conditions exist.

Digger Derrick Auger Fast Change System


6


Fast Change Bullet Tooth Head

The Fast Change bullet tooth head is best utilized in fracturable to solid rock formations.

Fast Change - Step Rock Heads

The Fast Change step rock head is best utilized in solid, non-fracturable rock.

9” Bullet Head P/N 9000-33607 9” Step Rock head P/N 9000-54680






30” Bullet Head P/N 9000-33613

Fast Change - Spiral Rock heads

The Fast Change spiral rock head is best utilized in solid, non-fracturable rock.

8” Spiral Rock head P/N 9000-56150 20” Spiral Rock head P/N 8855-10000







Digger Derrick Auger Fast Change System cont.

7


Hex HubsP/N 0700-00009 Hub for 2” hex drive

P/N 0700-09011 Hub for 2 1/2” hex drive


P/N 9000-54205 Hub for 3” hex drive


AdaptersP/N 9000-32419 2 1/2” hex hub x 2” hex stem

P/N 9000-32984 2 1/2” hex hub x 2 5/8” hex stem

P/N 9000-32609 2” hex hub x 2 1/2” hex stem

P/N 9000-99797 2 5/8” hex hub x 2 1/2” hex stem

P/N 9000-96171 2” hex hub to 2-1/2” hex hub

P/N 9000-34797 3-1/2” female to 3” male square

Kennametal Type Shank Plate with bullet teeth


16” diameter P/N 9000-54435 P/N 9000-54450

18” diameter P/N 9000-54436 P/N 9000-54451

20” diameter P/N 9000-54437 P/N 9000-54452

24” diameter P/N 9000-54438 P/N 9000-54453

CouplersP/N 9000-53400 2” x 2” hex coupler

P/N 9000-53402 2-1/2” x 2-1/2” hex coupler

P/N 9000-53403 2-5/8” x 2-5/8” hex coupler

P/N’s 9000-54481, 0700-09011, 9000-34675 and 700-90121

Utility Rock AugerRock Ripper® Shank Plates with bullet teethUtility Rock Auger, 2 1/2” and 2 5/8” hex hubs, overall length of 104”, with 60” of flight, Rock Ripper® shank plates, bullet teeth and P/N 9000-34675 (P/N RRP-MD) pilot bit.

Description 2 1/2” hex hub 2 5/8” hex hub 16” diameter P/N 9000-54480 P/N 9000-54495

18” diameter P/N 9000-54481 P/N 9000-54496

20” diameter P/N 9000-54482 P/N 9000-54497

24” diameter P/N 9000-54483 P/N 9000-54498

Digger Derrick Utility Rock Augers

Utility Rock Auger, 2 1/2” and 2 5/8” hex hub, overall length of 104” with 60” of flight, Kennametal Type shank plates, bullet teeth, and P/N 7163-02160 pilot bit.

Hex Hubs, Adapters, & Couplers

Digger Derrick Utility - Kennametal-Type Bullet Augers


8


P/N 700-90062 Ordinary digging (1650)

P/N 700-90155

P/N 700-90096

P/N 700-90091

P/N 700-90097 Abrasive soil, impact, hardfaced w/carbide chips 2 sides (1650-HFFTC)

P/N 700-90063 Tungsten carbide (round) High abrasion, frozen soil, low impact (1656)

P/N 700-90155 Tungsten carbide (flat), high abrasion, frozen soil, low impact (1654)

P/N 700-90096 Combination dirt/chisel point, installs rib up (1851)

P/N 700-90228 Ridge Breaker Carbide tooth, high abrasion, frozen soil, low impact (RB-56)

P/N 700-90095 Gage tooth, dirt (1652)

P/N 700-90228

P/N 700-90095

P/N 700-90229

P/N 700-90091 Carbide gage, highly abrasive soil, frozen ground (1658)

P/N 700-90229 Ridge breaker carbide gauge tooth, high abrasion, frozen soil, low impact (RB-58)

This carbide faced tooth for the step rock auger is best used in solid, non-fracturable rock.

Bullet Replacement TeethP/N 700-90121 Rock Ripper® Bullet Tooth C-3LR-94P/N 700-90162 Kennametal Bullet Tooth C-87-LRP/N 700-90161 Kennametal Bullet Tooth C-387-LRP/N 9000-34053 KennametalBullet Tooth C-31-HD

This replacement tooth for the spiral rock auger is carbide tipped and best utilized in non-fracturable rock with no impact.

P/N 700-09008 PFC-5

P/N 700-90181 604-C

Auger Tooth HoldersP/N 9000-34039 Rock Ripper® Auger C-10

P/N 9000-40119 Step Rock Auger PFC-5H

P/N 9000-57000 Spiral Rock Auger 1604

P/N 9000-71575 Dirt Auger WO-5 replacement tooth holder

P/N 9000-34574 Dirt Auger WO-5S straight pocket holder

Ribd-Rubr-Lok® used for installing auger teeth. Available in 4 ft. length.P/N 700-90060

Soft rubber mallet used to drive auger teeth into place.P/N 7163-02003

Drift punch used to remove worn auger teeth.P/N 9000-37750

Installation Tools

Bullet Tooth PullersP/N 9000-99908 Bullet Tooth Puller C-30P/N 9000-34091 Bullet Tooth Puller C-123

P/N 700-90062

Auger Teeth & Accessories

P/N 700-90063

9


P/N 700-90065 Fits 8”, 9” & 10” augers , 1 tooth per shank, 1 bolt per shank

P/N 700-90066 Fits 12”, 2 teeth per shank, 1 bolt per shank

P/N 700-90067 Fits 14”, Requires 2. 2 teeth per shank, 2 bolts per shank

P/N 700-90069 Fits 16”, 2 teeth per shank, 2 bolts per shank










P/N 7163-02087 Fits 26 & 27”, 4 teeth per shank, 4 bolts per shank

P/N 7163-02088 Fits 26 & 27”, 4 teeth per shank, 4 bolts per shank





72” P/N 9000-80007 2-1/2” extension, 2-5/8” couplingP/N 700-00015 2 5/8” extension, 2 5/8” couplingP/N 700-00041 2 1/2” extension, 2 1/2” couplingP/N 700-00058 2 5/8” extension, 2 1/2” coupling

This rugged and easily installed hex hub extension shaft ex-tends the shaft past the body of the truck to allow accessory parts (like a capstan or butterfly reel) to be easily added to and run off the shaft. These extension shafts have an overall length of 72”.

P/N 700-00041

Kelly Bar Hex Extension Shafts

Shank Plates - 1650 Series


10

Shank plates bolt onto the standard heads and allow drilling to occur in permafrost, concrete and most fracturable rock.

Shank Plates & Pilot - Kennametal Type Bullet Style

Shank Plates & Pilot - Rock Ripper®

Rock Ripper® Bullet Style Shank Plates & Pilot

P/N 9000-33634 16” Diameter Shank & Pilot KitP/N 9000-34673 16” Diameter Shank - LeftP/N 9000-34674 16” Diameter Shank - Right P/N 9000-91606 18” Diameter Shank & Pilot KitP/N 9000-34569 18” Diameter Shank - LeftP/N 9000-34566 18” Diameter Shank - Right

P/N 9000-34720 20” Diameter Shank & Pilot KitP/N 9000-34717 20” Diameter Shank - LeftP/N 9000-34718 20” Diameter Shank - Right

P/N 9000-34697 24” Diameter Shank & Pilot KitP/N 9000-34695 24” Diameter Shank - LeftP/N 9000-34696 24” Diameter Shank - Right

P/N 9000-34675 Rock Ripper® MD Pilot Bit

P/N 700-90121 Rock Ripper® Teeth

The Rock Ripper® bolt-on shanks and pilot are computer designed to easily interchange with Pengo’s standard shanks and pilot. Best suited for solid and fracturable rock as well as compacted soils. The Rock Ripper® series comes with stan-dard Rock Ripper® bullet teeth (bolts and nuts included).

P/N 9000-34675

Part # Description Quantity Approx. Wt. Lbs.P/N 700-09001 16” Diameter Kit 13 teeth 43.5P/N 700-09007 18” Diameter Kit 15 teeth 48P/N 700-09003 20” Diameter Kit 15 teeth 51.5P/N 700-54233 24” Diameter Kit 17 teeth 26.5P/N 700-54240 16” Shank Plate 4 teeth 12.5P/N 700-54241 18” Shank Plate 5 teeth 15P/N 700-54242 20” Shank Plate 5 teeth 16.5P/N 8938-51410 24” Shank Plate 6 teeth 19P/N 7163-02160 6-1/2” Center Point 5 teeth 18.5P/N 700-90162 Conical Tooth 0.6P/N 700-90161 Conical Tooth 0.5

Shank Plates - Bolt On Bullet

11


This 4 3/4” carbide pilot is best used in solid, nonfracturable rock.

P/N 9000-37350 Utility Tri-Flow

P/N 8994-08330 P-1656

P/N 700-90123 P-1650

P/N 700-09002 50-TCH-171

This replacable tooth pilot bit is best used in compacted soil and fracturable rock.

This 5” diameter carbide tipped drill head is best used in concrete, stone, and frozen ground.

This triple-fluted patented, Utility Tri-Flow® pilot bit has three rather than two flutes for 50% longer wear than the P/N 700-90061 (FH-205). This bit is interchangeable and replaces the P/N 700-90061 (FH-205).

This pilot is best utilized in ordinary dirt applications.

P/N 700-90061 FH-205

This pilot is best utilized in consolidated rock and abrasive soil where impact is minimal.

P/N 7163-02018 FH-105

This hardpan pilot, with bit, bolt & nut is best used in dirt. This pilot bit does not need an adapter to install into the head.

P/N 9000-31730 C-120

This cone pilot bit installs into the head with-out an adapter. Used best in drilling dirt.

P/N 700-90176 FH-205C

This replaceable carbide tooth pilot bit is best used in consolidated rock and abrasive soil where impact is minimal.

P/N 700-90093 PA-183-LP/N 7163-02107 PA-182-L (shown)

These pilot bit adapters come with a bolt & nut. P/N 700-90093 is the standard pilot bit used, P/N 7163-02107 is a short pilot bit.

P/N 9000-51273 P-6000

P/N 9000-34676 RRP-API Rock Ripper® API Pilot BitP/N 9000-33520 RRP-4API Rock Ripper® 4API Pilot BitP/N 9000-32191 RRP-2 3/8” API Rock Ripper® Pilot Bit

P/N 7163-02160 6 1/2” Center Pilot 5 teeth

Rock Ripper® Pilot Bits

Kennametal Type Pilot BitReplacement Bolts & NutsP/N 9000-11582 3/8” x 3” bolt and nut (used on P/N 0700-09002)P/N 7163-02105 1/2” x 4-1/2” bolt and nut (used on P/N 0700-90123 and P/N 7163-02018)

Pilot Bits & Adapters

Auger Accessories

P/N 9000-66666 7 ft triangle blanketP/N 9000-66667 6x6 ft square blanketP/N 9000-66668 7x7 ft square blanketP/N 9000-66669 8x8 ft square blanket

6x6 Covers 36 sq ft; Holds 14 cu ft; Rated lift 700 lbs or 1/4 cu yd dirt; Poles to 35’ small hand dig 7x7 Covers 49 sq ft; Holds 22 cu ft; Rated lift 1,100 lbs or 3/8 cu yd; All poles to 55’ 8x8 Covers 64 sq ft area; Holds 34 cu ft; Rated lift 1,400 lbs or 1/2 cu yd dirt; All poles

The Altec Dirt Sling is a flat “blanket” that is made of heavy duty 22 oz. vinyl and strengthened with heavy duty 2” web-bing sewn around the edges. This tarp, which attaches to winches, acts as a sling and makes filling in dirt around poles, transporting crushed rock, sand, dirt, wet cement, etc. quickly and simply. The dirt sling maintains clean work areas and transport vehicles. Tools and other materials will be easy to find when used as a blanket, as it will sit atop weeds, grass, mud, or snow. When a job is incomplete, dirt can be transported from the worksite to a dry area to be replaced when the job is finished.

As a safety device, the dirt sling reduces injuries by elimi-nating the demanding forces associated with physical labor and repetitive movements. This innovative sling essentially does the work for you and makes the job cleaner, easier, safer, and much more productive.

The Auger Bag acts as a dirt cover, preventing mud and dirt from falling into the truck bed as well as preventing rocks and dirt from hitting passing cars. This bag is made from heavy duty vinyl which allows for long-term use. P/N 9000-99718 Auger Bag


1-877-GO ALTEC

Contact your nearest Altec location for assistance with all part and accessory needs.

Wind Up Slings

P/N 234-11001 102” long (8’6”) wire ropeP/N 234-11024 114” long (9’6”) wire rope

P/N 234-80004 10 Ft NylonP/N 234-80005 9 Ft Nylon

Auger wind-up slings are available in both nylon and wire rope.

Auger Bag

Documents

ALTEC Augers