ALIANS DISTAL rADIuS - Newclip Technics mEAS mOTIONN POLYAXIAL LOCKING SYSTEm ALIANS DISTAL rADIuS Precontoured implant Polyaxiality of 20 Single diameter: ø2.8mm DUALTEC SYSTEM ®

INN O VAT I O N mE A N S m OT I O N

POLYAXIAL LOCKING SYSTEm

ALIANS DISTAL rADIuS

Precontoured implantPolyaxiality of 20°Single diameter: ø2.8mm

DUALTEC SYSTEM ® II


T ECHNI C A L FE AT UR ES

ANATOmICAL PLATE wITH OPTImIzEd FIXATION SLOTS

ø2.8mm SINGLE dIAmETER FIXATION SCREwS

Hole for insertion of a K-wire to locate the joint space.

The window in the plate allows for better visualization of the fracture reduction.

K-wire holes for temporary fixation.

A PRE-CONTOUREd ImPLANT

The distal edge of the plate runs alongside the watershed line.

The design of this implant is the result of a proprietary state-of-the-art mapping technology to establish the maximum congruence between the plate and the bone.

The plate offers:

• optimal metaphyseal / diaphyseal curvature.

• different medial and lateral radii of curvature for optimal volar tilt.The round edge of the low profile plate is designed

for minimal irritation of soft tissues and flexor tendons.

EPIPHYSEAL FIXATION ø2.8 locking screws

Distal slots : 2 monoaxial locking slots in the middle of the plate2 polyaxial locking slots (+/- 10°) on each side of the plate (1 on the radial styloid side, 1 on the ulnar side)

Proximal slots : 2 monoaxial locking slots

dIAPHYSEAL FIXATION

ø2.8 screws

1 oblong slot to facilitate the positioning of the plate Cortical screw

2 monoaxial locking slots Locking screws

Holes for fastening fast guide onto the plate.

Locking screw

Length: 10-28mm Ref. SDT2.8Lxx

Cortical screw

Length: 10-18mmRef. CT2.8Lxx

Non locking screw

Length: 16-28mmRef. QDT2.8Lxx

The blunt-tipped screw is designed for minimal irritation of soft tissues and extensor tendons.

ANGULAR RANGE: +/-10° POLYAXIAL LOCKING RANGE

Principe de la fixation polyaxiale : la technologie DTS2® Ecrou + clip prémontés sur la plaque

* Angulation based on the slots’ axes in the diaphyseal area.

AVERAGE PRE-dETERmINEd ANGULATIONS OF PLATE SLOTS*

Ulnar 7°Distal 16.8°

Ulnar 0.6°Distal 17°


Radial 5.6°Distal 15.2°

Ulnar 7°Distal 16.8°

Ulnar 0.4°Distal 13.5°



Ulnar 2.5°Distal 33.4°



Radial 9°Distal 24.3°

Radial 9.2°Distal 27.1°Radial 19.9°Distal 41.3°

In the epiphyseal area, slots have pre-determined angulations (see diagrams below).Thanks to the DTS2® polyaxial locking system, distal slots for styloid process and on the ulnar side allow an additional angulation of +/- 10°.

DTDVPN1 DTDVPS1

DTDVPN2 / DTDVPS2

Polyaxial locking screw

+/-10° locking range

poLyaxIaL LoCKIng pLaTE sysTEmDTs2® TECHnoLogy

gREaTER angULaTIon Is possIbLE: +/-10° LoCKIng RangE

Polyaxial locking nut and clip


S UR GI C A L T ECHNI Q UE

SImPLE REdUCTION

Reduction of the fracture. Temporary fixation with K-wire.

Drill (anC088) using the guide gauge (anC450) and insert a cortical screw (CT2.8Lxx) into the oblong slot. The depth can be directly read on the guide gauge.

1

The fast guide is locked onto the plate with the screwdriver (anC082).

simple fracture

FINAL RESULT

If necessary, the position of the plate can be adjusted thanks to the oblong slot before the cortical screw is tightened (see a).The plate can be provisionally stabilized with K-wires (see b).

a) b)

The joint space is assessed using a 1.4mm K-wire (K-Wire-D1.4-L120).

Drill (anC088) and read depth directly on the guide gauge (anC046) for epiphyseal slots.

SDT2.8Lxx distal locking screws are inserted through the fast guide using the screwdriver (anC082).

The construct is finalized by inserting SDT2.8Lxx locking screws into the diaphyseal area.

REdUCTION OF THE FRACTURE USING THE PLATE

Drill (anC088) and read depth directly on the guide gauge (anC268R) or insert the depth gauge (ANC102) for checking.

Insert the screw and lock it using the screwdriver (anC082).

screw the guide gauge (anC268R) into position in the DTs2® polyaxial slot.Angulate the locking guide gauge as wished, and then tighten it.

step 1

step 2

step 3

FAST guIDe

pre-angulation of the screws offered by the fast guide for quick, simplified surgical procedure (see opposite).

Fast guides are also suitable and optional if the polyaxial technique is chosen.

guIDe gAugeS

Non-locking guide gauge anC046Used in combination with the fast guide for screw insertion:- into monoaxial locking slots- into polyaxial locking slots using the fast guide pre-angulation.

Locking guide gauge anC268R (or anC558)

- Suitable both for the polyaxial and the monoaxial techniques - Allows +/-10° locking range with DTs2® slots.

INSTRUmENTS for monoaxial and/or polyaxial techniques in epiphyseal area

POLYAXIAL SURGICAL TECHNIQUE

anC046

anC268R

Lock the guide gauge (ANC268R) onto the plate, drill (anC088), then insert the distal screw (SDT2.8Lxx). Repeat for all distal slots. (See Polyaxial surgical technique).

The fracture is reduced using the plate until both anterior cortical lines are in place.

Insert and tighten the cortical screw (CT2.8Lxx) into the oblong slot. Complete the fixation by inserting all the locking screws in the remaining slots (SDT2.8Lxx).

Complex fracture


A LI A NS d ISTA L R A d IUS R A N GE

RIGHT PLATES - GREEN ANOdIzEd

DTDVpn2

20.7 mm

52

mm

DTDVps2

23.7 mm

52

mm

DTDVpW1

60.

2 m

m

27.6 mm

DTDVps3

90.

1 m

m23.7 mm

DTDVps1

23.7 mm

41 m

m

DTDVpn1

19.5 mm

41 m

m

DTgVps3DTgVpW1 DTgVps2 DTgVpn2DTgVps1 DTgVpn1

LEFT PLATES - BLUE ANOdIzEd

ø2.8mm CORTICAL SCREwS*

Ref# DescriptionCT2.8L10 Ø2.8mm cortical screw - L10mm

CT2.8L12 Ø2.8mm cortical screw - L12mm




ø2.8mm LOCKING SCREwS*

Ref# DescriptionsDT2.8L10 Ø2.8mm locking screw - L10mm

sDT2.8L12 Ø2.8mm locking screw - L12mm









* Green anodized.

ImP L A N TS R EFER EN CES

OPTIONAL

ø2.8mm NON LOCKING SCREwS*

Ref# DescriptionQDT2.8L16 Ø2.8mm non locking screw - L16mm

QDT2.8L18 Ø2.8mm non locking screw - L18mm






* Golden anodized.

nb :

please note that all implants are also available in sterile packaging.The Sosafe tube packaging is handy and easy to use.an “sT” code is added at the end of the reference, e.g. “sDT2.8L12-sT”

* Non anodized.Sterile screws are pink anodized.

ALIANS RAdIUS PLATES

Ref# Description DTDVpn1 Polyaxial plate for distal radius - Narrow head - Size 1 - Right

DTgVpn1 Polyaxial plate for distal radius- Narrow head - Size 1 - Left

DTDVpn2 Polyaxial plate for distal radius - Narrow head - Size 2 - Right

DTgVpn2 Polyaxial plate for distal radius - Narrow head - Size 2 - Left

DTDVps1 Polyaxial plate for distal radius - Standard head - Size 1 - Right

DTgVps1 Polyaxial plate for distal radius- Standard head - Size 1 - Left


DTgVps2 Polyaxial plate for distal radius - Standard head - Size 2 - Left


DTgVps3 Polyaxial plate for distal radius - Standard head - Size 3 - Left

DTDVpW1 Polyaxial plate for distal radius - Wide head - Size 1 - Right

DTgVpW1 Polyaxial plate for distal radius - Wide head - Size 1 - Left

oPtional ScrewS

INST R UmEN TS R EFER EN CES

OPTIONAL INSTRUmENTS (for implants provided sterile)

Ref# Description QtyanC477 DTgVps1 phantom plate 1

anC478 DTDVps1 phantom plate 1

anC479 DTgVps2 phantom plate 1


anC481 DTgVpn1 phantom plate 1

anC482 DTDVpn1 phantom plate 1

anC483 DTgVpn2 phantom plate 1

anC484 DTDVpn2 phantom plate 1

anC485 DTgVpW1 phantom plate 1

anC486 DTDVpW1 phantom plate 1

anC495 DTgVps3 phantom plate 1


INSTRUmENTS

Ref# Description QtyanC046 Ø2.0mm guide gauge 1

anC082 2.0mm hexagonal prehensor 2

anC088 Ø2.0mm quick coupling drill bit – L125mm 2

anC102 Length gauge for Ø2.8mm screw 1

anC103 2.0mm hexagonal non prehensor screwdriver 1

anC268R Ø2.0mm guide gauge for locking screws 2

anC350 Ø4.5mm AO quick coupling handle - Size 1 2

anC435 Reduction tool 1

anC450 guide gauge for Ø2.8mm cortical screws 1

anC465 Fast guide for DTgVps2 and DTgVps3 plates 1

anC466 Fast guide for DTDVps2 and DTDVps3 plates 1

anC487 Fast guide for DTgVpW1 plate 1

anC488 Fast guide for DTDVpW1 plate 1

anC501 Fast guide for DTgVpn2 plate 1

anC502 Fast guide for DTDVpn2 plate 1

anC503 bone Reduction Forceps 1

anC504 bone Reduction Forceps, curved, pointed 1

anC557 Length gauge 1

anC558 Ø2.0mm guide gauge for locking screws 1

K-WIRE-D1.4-L120 K-wires - Ø1.4 L120mm 3

NEWCLIP TECHNICSPA de la Lande Saint Martin - 45 rue des Garottières44115 Haute Goulaine (France)Phone : +33 (0)2 28 21 23 25 - Fax : +33 (0)2 40 63 68 [email protected] - www.newcliptechnics.com

broc

hure

gb

- alia

ns R

adiu

s - E

d11

- 09/

2013

- m

edic

al d

evic

e cl

ass

IIb -

CE

sgs

UK

- Rea

d la

belin

g an

d in

stru

ctio

ns b

efor

e us

e.n

on-c

ontra

ctua

l pic

ture

s.

SET dESCRIPTION

ImpLanTs TRay

InsTRUmEnTs TRay

NEWCLIP USA642 Larkfield Center Santa Rosa CA 95403, USAPhone : + 1 707 888 [email protected] - www.newclipusa.com

The information presented in this brochure is intended to demonstrate a NEWCLIP TECHNICS product. Always refer to the package insert, product label and/or user instructions before using any nEWCLIp TECHnICs product. surgeons must always rely on their own clinical judgment when deciding which products and techniques to use with their patients. products may not be available in all markets. Product availability is subject to the regulatory or medical practices that govern individual markets. Please contact your NEWCLIP TECHNICS representative if you have questions about the availability of nEWCLIp TECHnICs products in your area.

Documents

ALIANS DISTAL rADIuS - Newclip Technics mEAS mOTIONN POLYAXIAL LOCKING SYSTEm ALIANS DISTAL rADIuS Precontoured implant Polyaxiality of 20 Single diameter: ø2.8mm DUALTEC SYSTEM ®