ALFA TCT Transmission - Fiat-Lancia Club Serbia ?· Acoustic warning ... Parking the car ... ALFA MiTo…

  • Published on
    09-Jul-2018

  • View
    212

  • Download
    0

Transcript

ALFA TCT TransmissionENGLISHAlfa ServicesCOP. ALFA MITO TCT GB 25-03-2010 15:08 Pagina 1ALFA MiToALFA TCT TransmissionUsing the transmission .....................................................................................2Position of the lever ........................................................................................3Engine starting ................................................................................................4Start&Stop system ..........................................................................................5Engine switching off ........................................................................................6Moving the car ...............................................................................................7Automatic driving mode ...................................................................................8Sequential driving mode ...................................................................................9Acoustic warning ...........................................................................................10Parking the car .............................................................................................10Towing the car ...............................................................................................10General warnings ..........................................................................................10Warning lights and messages ..........................................................................11Replacing fuses .............................................................................................12Maintenance and care ....................................................................................12Level check ...................................................................................................12Technical specifications ...................................................................................13Transmission ..................................................................................................13Engine ..........................................................................................................13Performance ..................................................................................................14Weights ........................................................................................................14Fluids and lubricants ......................................................................................15Fuel consumption ..........................................................................................16CO2 Emissions ..............................................................................................16This supplement describes all the main char-acteristics of the Alfa TCT 6-speed dual clutchdry automatic transmission installed on thecar.In order to be able to use the transmissioncorrectly, this Supplement should be readcarefully and completely in order to under-stand the correct, permitted operations fromthe outset.For all other information, comply with theinstructions of the Owner Handbook.SUMMARY 1604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 12SELECTOR LEVER fig. 1P = ParkingR = ReverseN = NeutralD = Drive, automatic forward gear+ = Sequential upshifting = Sequential downshifting.If the lever is used in sequential mode, mov-ing the latter from D to the left, the positionstowards + or are unstable.The gear lever has a button A, that must bepressed to move the lever to the positionsP or R (fig. 2 for right-hand drive versions).USING THETRANSMISSIONINTRODUCTIONThe car is equipped with an electronically-managed Alfa TCT 6-speed automatic trans-mission where gearshifting takes place au-tomatically depending on the instantaneouscar usage parameters (vehicle speed, roadgradient and accelerator pedal position).The new transmission is an absolute inno-vation as it matches the Start&Stop systemwith the most recent alternative to tradi-tional automatic transmissions with built-intorque converter.Manual gearshifting can still occur thanks tothe sequential mode position of the gear lever.DISPLAYThe display can show the following: in automatic driving mode, the speed se-lected (P, R, N or D), fig. 3; in sequential driving mode the manual en-gagement of a higher or lower gear, re-spectively, with the relevant number fig. 4.fig. 1A0J0360mfig. 3 A0J0361mfig. 4 A0J0362mfig. 2 A0J0367m604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 23POSITIONS OF THE LEVERParking (P)Position P corresponds to the neutral posi-tion of the transmission and locks drivewheels mechanically. It should only be en-gaged with the car stationary and the hand-brake should be applied, if necessary.With the ignition key in MAR or with enginerunning, or when the engine switches off,if the gear lever is not correctly positioned inP, the gear lever trim starts flashing next toletter P. In this case, position the lever cor-rectly in P.The ignition key can be removed only whenthe lever is in position P. Moving the leverfrom P to D must be performed only whenthe car is stationary and the engine atidling speed.Shifting from P to any other position of theselector lever, with ignition key in MAR po-sition, must be made pressing the brake ped-al and using the button on the gear lever (A-fig. 1).ALFA MiToALFA TCT TransmissionIf the car is on a gradient, always pull the handbrakeBEFORE placing the brakelever in P.If the battery is flat, to releasethe lever you need to removethe gaiter and operate thelever A-fig. 5.Engage reverse only with thecar stationary, engine at idlingspeed and accelerator fully released.IMPORTANT Never leave the car beforehaving positioned the selector lever in P.Shifting from R to N or D is free, while shift-ing from R to P can only be made by thebutton on the gear lever, with engine atidling speed.Neutral (N)It corresponds to neutral for a standard,manual gearbox.The engine can be started with the lever inposition N.Engage N in case of prolonged stops.To move the lever from position N, releasethe accelerator and make sure the engine isstable at idling speed.Shifting from N to D is free, while shiftingfrom N to R or P can only be made by thebutton on the gear lever.fig. 5 A0J0363mReverse (R)The engine cannot be started with the leverin position R.604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 34D (D automatic forward gear)It is the lever position in standard runningconditions.Shifting from D to N is free, while shifting fromD to R or P can only be made by the buttonon the gear lever.Sequential mode (+/)Shifting the lever from position D, to the left,to use the transmission in sequential mode,the lever is used in unstable position + or for up/downshifting.SummarisingAll movements of the gear lever must be per-formed with car stationary and engine idlingonly. The drive wheels are mechanically lockedin position P; Shifting from P R is possible withbrake pedal pressed and button on gearlever pressed; Shifting from R N is free; Shifting from N D is free; Shifting from D sequential mode isfree; Shifting from sequential mode D isfree; Shifting from D N is free; Shifting from N R is possible with but-ton on gear lever pressed; Shifting from R P is possible with but-ton on gear lever pressed.ENGINE STARTINGThe car is provided with an electronic enginelock device. In case of failed starting, referto the paragraph Alfa Romeo CODE sys-tem, chapter Getting to know your car,on the Owner Handbook to which this Sup-plement is attached.Starting is only permitted with gear leverin position P or N (with or without brake ped-al pressed). At starting, the system is in Nor P (the latter corresponds to transmissionneutral, but the cars wheels are mechani-cally locked). 604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 45START&STOP SYSTEMWith car at a standstill and Start&Stop sys-tem activated (see Owner Handbook towhich this Supplement is attached), the en-gine switches off if the gear lever is in aposition other than R. The Start&Stop system does not operatewhen the gear lever is in R, for making park-ing manoeuvres easier.In the event of stops uphills, the engineswitching off is disabled to activate the HILLHOLDER function, that works with runningengine only, as described in the chapter Get-ting to know your car, on the Owner Hand-book to which this Supplement is attached.The engine automatic restarting occurs if: the brake pedal is released and the leveris not in N or P; the lever is shifted to an unstable posi-tion, +, or R; the lever is moved from D to the left, se-quentially; by the levers + or on the steering wheel(for versions/markets where provided).During the car switching off and on, the sys-tem passes through the automatic engage-ment of neutral and the display shows N.IMPORTANT In some conditions (for ex-ample with reduced gradients and brake ped-al not fully pressed), the engine switchingoff is not deactivated. In this event, fully pressthe brake pedal to make the HILL HOLDERfunction available and restart the engine, us-ing the gear lever or the levers on the steer-ing wheel (for versions/markets where pro-vided) as above described.ALFA MiToALFA TCT Transmission604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 56ENGINE SWITCHING OFFEngine can be switched off in any positionof the gear lever.Ignition key removalThe ignition key can be removed only if thegear lever is in position P: if the engine is switched off with the gearlever in position P the ignition key can beremoved within 30 seconds; if the engine is switched off with the gearlever in a position other than P, the P let-ter on the instrument panel display andon the gear lever trim flashes for 5 sec-onds. At the same time there is also asound signal. Move the lever to P with-in 5 seconds; then it will be possible toremove the ignition key for 30 seconds. If the battery is flat and theignition key is engaged, thelatter is locked in position. Toremove the key mechanically, proceedas follows: pull the handbrake and fitthe supplied screwdriver in the holeunder the dashboard (A-fig. 6), slight-ly pressing, until the ignition key canbe removed.fig. 6 A0J0364mIn both cases, if the described conditions andtimes are not respected, the ignition key willbe automatically locked. To remove the key,turn it to MAR and then to STOP.604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 67MOVING THE CAR To move the car, from P press the brake ped-al and, using the button on the gear lever,move the lever to the wished position (D, Ror sequential).The display shows the speed engaged.Releasing the brake pedal, the cart startsmoving forwards or backwards, as soon asthe manoeuvre is activated (creeping ef-fect). The accelerator should not be pressed.IMPORTANT The inconsistency betweenthe speed actually engaged in the trans-mission, shown on the display of the con-trol panel, and the position taken by thegear lever is signalled by the flashing, onthe trim, of the letter corresponding to theposition of the lever itself accompanied byan acoustic signal.This condition should not be interpreted asan operational failure, but simply as a re-quest by the system to repeat the ma-noeuvre.IMPORTANT With engine running and carat a standstill, in sequentially mode, the re-quest for engaging the 2nd speed is not ac-cepted by the system (pressing the brakepedal or not).If, with engaged 1st speed or reverse (R),the following conditions occur: road slope over 5%; clutch overheated; engine torque steady for a given time in-terval (for example, if the car hits the pave-ment or is parked downhills/uphills);the car movement is obtained by pressingthe accelerator pedal.IMPORTANT With handbrake releasedand brake pedal released, engine at idlingspeed and gear lever in position D, R or se-quential, pay the utmost care because thecar can move also without pressing the ac-celerator pedal. This condition can be used with the car ona level surface during tight parking ma-noeuvres using the brake pedal only.ALFA MiToALFA TCT Transmission604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 78AUTOMATIC DRIVING MODED can be selected from sequential operationin any driving conditions.In automatic driving mode, the best ratiois selected by the transmission electroniccontrol unit depending on speed, engineload (accelerator pedal position) and gra-dient of the road.To resume speed quickly, when the accel-erator pedal is pressed fully, the transmis-sion control system downshifts (kick-downfunction).IMPORTANT When driving on roads withpoor grip conditions (snow, ice, etc.) avoidactivating the kick-down device.Integration with DNAOperating the Alfa DNA system fig. 7, threedifferent driving modes can be selected: Normal: gearshifting at low enginespeeds, enhancing comfort and reducing con-sumption; Dynamic: gearshifting at higher enginespeeds, enhancing sporty driving; All Weather: driving programme onroads with poor grip (example snow, ice,mud, etc.). Gearshifting suggestionWhile driving with the transmission in au-tomatic mode (selector lever in position D),when gearshifting is required by the levers(fig. 8) on the steering wheel, the systemshifts to fully manual mode, with relevantdisplaying of the gear engaged, for about 5 seconds; then, if the levers are not op-erated anymore, the system goes back tothe automatic mode (D), with followingdisplaying.fig. 7 A0J0366m fig. 8 A0J0365m604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 89ALFA MiToALFA TCT TransmissionGearshifting through steeringwheel controls (for versions/markets where provided)On some versions, gearshifting can occur bythe controls on the steering wheel fig. 9.To use the controls on the steering wheel, thegear lever must be in a sequential position: moving the lever + on the steering wheel:upshifting; moving the lever on the steering wheel:downshifting.The upshifting/downshifting is only permit-ted if the engine revs allow it.If the car is stopped with a higher gear than1st speed engaged, the transmission will au-tomatically engage 1st gear.fig. 9 A0J0365mSEQUENTIAL DRIVING MODEIn sequential driving mode, the transmissionworks like a manual gearbox.Gearshifting through gear leverMove the lever sideways (to the left) man-ually from position D to the sequential po-sition: lever towards +: upshifting lever towards : downshifting.The lever correct position in Sequential Modeis signalled when the symbols + and switch on and the symbol D switches off.The gear engaged is displayed.604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 910ACOUSTIC WARNINGFor safety reasons, an acoustic signal isheard when: the drivers side door is opened with en-gine running and the gear lever is in a po-sition other than P; if engine is switched off with gear leverin a position other than P.With the car stationary, the engine startedand (1), (D) or (R) engaged, the system ac-tivates the acoustic signal and automaticallyplaces the transmission in neutral (N) when: the accelerator/brake pedals are notpressed for at least 3 minutes with creep-ing deactivated (for example with hand-brake engaged); the brake pedal is pressed for longer than10 minutes; the drivers door is opened with creepingdeactivated (for example with handbrakeengaged) without pressing brake and/or ac-celerator pedals; a fault has been detected in the trans-mission.IMPORTANT Shifting to neutral (N) op-erated by the system involves a situationof inconsistency between gear lever positionand speed engaged in the transmission. Themanoeuvre is accompanied by an acousticinconsistency signal. The acoustic signal con-tinues until the gear lever is placed in P orN, to restore consistency.PARKING THE CARTo park safely, keeping the foot on the brakepedal, first P must be engaged and, in caseof parking uphills/downhills, the handbrakemust be engaged. Before releasing the brakepedal, wait until P on the display appears.IMPORTANT NEVER leave the car beforehaving positioned the lever in P.TOWING THE CARMake sure that the transmission is in neu-tral (N), checking that the car moves off andproceed in the same way as for towing anormal car with a manual gearbox (see de-scription in Owner Handbook).IMPORTANT If the transmission cannotbe placed in neutral (N), do not tow the car,rather contact an Alfa Romeo Authorized Ser-vice and, should the lever be in P, see therelease procedure on page 3 before towingit.GENERAL WARNINGSWith the car stationary and a gear engaged,always keep the brake pedal pressed untilyou decide to set off, then release the brakeand accelerate slowly. During prolongedstops with the engine running, it is advisableto keep the transmission in neutral (N).To protect the clutch, never use the accel-erator to keep the car stationary (for ex-ample when stopped uphills/downhills):clutch overheating could damage it. Use thebrake pedal instead or the handbrake andonly press the accelerator pedal when youwish to set off.604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 1011ALFA MiToALFA TCT TransmissionAlthough it is strongly unadvisable, if youare driving downhill and, for unexpectedreasons, you let the car move forward withthe transmission in neutral (N), when thereis a request to engage a speed, depend-ing on the actual speed of the car, the sys-tem will automatically engage the bestspeed for the correct transmission of drivetorque to the wheels.WARNING LIGHTS AND MESSAGESALFA MitoALFA TCT TransmissionAutomatictransmission failureIn the event of transmissionfailure, contact Alfa RomeoAuthorized Services as soon aspossible to have the system checked.tThe following messages can also be dis-played on the control panel without thewarning light switching on and therefore can-not be considered as failures, but as sim-ple driving suggestions:Operation not admissibleThe message is displayed when a manoeu-vre not compatible with correct system op-eration is carried out. (For example, if thereverse gear is requested while the vehicleis moving). The message on the display is accompaniedby an acoustic signal.Clutch overtemperatureIn this case it is necessary to limit the gearchanges and/or change the condition ofuse, until normal operating conditions arerestored.Never leave children unat-tended in the car. Always re-move the ignition key whenleaving the car and take the keywith you.If reverse (R) is engaged, only engage the1st gear or vice versa when the car is com-pletely stopped.When the ignition key is turned to MAR, thewarning light switches on but should switchoff after a few seconds.The warning light flashes (together with amessage in the display and an acoustic sig-nal) when it is detected that the transmis-sion is faulty.The messages that can be displayed on thecontrol panel together with the warning lightswitching on are:Check transmissionGear unavailableManual method unavailableIn this case sequential driving mode is notavailable and the transmission switches toautomatic operating mode.Automatic method unavailableIn this case it is necessary to move the controllever to sequential driving mode and continueto drive by engaging the speeds manually.604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 1112REPLACING FUSESThe automatic transmission components are protected by specific fuses. Contact an Alfa Romeo Authorized Service to have them replaced.For all other fuses, consult the Owner Handbook to which this Supplement is attached.MAINTENANCE AND CARE SCHEDULED SERVICING PLANIn addition to all the operations described above (see the Owner Handbook, chapter "Care and Maintenance"), the Scheduled ServicingPlan also includes the check and, if necessary, top-up of the electro-hydraulic actuator oil level every 120,000 km.LEVEL CHECK ALFA TCT TRANSMISSION ACTUATION SYSTEM OILTo check the transmission control oil level, contact exclusively Alfa Romeo Authorized Services.Used transmission oil contains substances that may be dangerous for the environment. We advise contacting Alfa Romeo Authorized Services to change the oil as they are equipped to dispose of the used oil in accordancewith legislation and without harming the environment.604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 1213ALFA MiToALFA TCT Transmission955A7000Otto4 in line72.0 x 84.013689.8991355000NORMAL DYNAMIC190 23019.4 2.44500 1750NGK IKR9F8Unleaded petrol 95 RON or 98 RON (EN228 specifications)955A7000955AXR11 12 (*)955AXR11 12B (**)TECHNICAL SPECIFICATIONS ENGINE CODE BODYWORK VERSIONSAutomatic, dual clutch and 6 speedsFront(*) 4-seater version(**) 5-seater versionTRANSMISSION ENGINEEngine Bodyworkcode versions1.4 Turbo Multi Air135HP TCT1.4 Turbo Multi Air 135HP TCTGearboxDriveGENERAL INFORMATION 1.4 TurboMulti Air 135HP TCTType codeCycleNumber and arrangement of cylindersPiston bore and stroke mmTotal displacement cm3Compression ratioMax power (EEC) kWHP corresponding speed rpmMax. EEC torque Nmkgm corresponding speed rpmSpark plugsFuel604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 13141170 1170480 560950 950850 8501650 1730500 500400 40040 4060 60PERFORMANCEWEIGHTS (kg) 1.4 Multi Air 135HP TCT4 seats 5 seatsUnladen weight (with all fluids, fuel tank filled to 90 % and without optional equipment):Payload (*) including the driver:Maximum permitted loads (**) front axle: rear axle: total: Towable loads: braked trailer: non braked trailer:Maximum load on roof:Maximum load on the ball joint (braked trailer):(*) If special equipment is fitted (sunroof, tow hitch, etc.) the unladen car weight increases, thus reducing the specified payload with respect to the maximum permitted load.(**) Loads not to be exceeded. The driver is responsible for arranging the loads in the boot and/or on the roof so that they comply with these limits.207 8.21.4 Turbo Multi Air 135HP TCTVersions Top speed (km/h) Acceleration 0-100 km/h (s)604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 1415ALFA MiToALFA TCT TransmissionSynthetic lubricant, SAE 75W-85 grade, for automatic transmissionsFIAT 9.55550-MZ3 specificationsSpecial fluid for electrohydraulic ratio selector actuators FIAT 9.55550-SA1 specificationsTUTELA CAR GEARTECHContractual Technical Reference No. F704.C08TUTELA CAR CS SPEEDContractual TechnicalReference No. F005.F98As per the Scheduled Servicing PlanAs per the Scheduled Servicing PlanFLUIDS AND LUBRICANTSRECOMMENDED PRODUCTS AND SPECIFICATIONSUse Fluid and lubricant features Genuine fluids Replacement for a correct use of the car and lubricants frequencyAutomatic transmission lubricantLubricant for electrohydraulic actuator604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 1516FUEL CONSUMPTIONFUEL CONSUMPTION ACCORDING TO EUROPEAN DIRECTIVE IN FORCE (litres/100 km)7.14.55.5CO2 EMISSIONSThe CO2 emission figures refer to combined consumption.CO2 EMISSIONS ACCORDING TO EUROPEAN DIRECTIVE IN FORCE1.4 Turbo Multi Air 135HP TCT: 126 g/km1.4 Turbo Multi Air 135HP TCTUrban cycleExtra urban cycleCombined consumptionCUSTOMER SERVICESTECHNICAL SERVICES SERVICE ENGINEERINGLargo Senatore G. Agnelli, 5 10040 Volvera Torino (Italia)Fiat Group Automobiles S.p.A.Print No. 60438250 2 Edition 08/2010Copyright. Reproduction, even partial, without written authorisationfrom Fiat Group Automobiles S.p.A. is prohibited.S E R V I C E604_38_250 Alfa Mito Cambio TCT 2ed ING 30-08-2010 16:12 Pagina 16ALFA TCT TransmissionENGLISHAlfa ServicesCOP. ALFA MITO TCT GB 25-03-2010 15:08 Pagina 1

Recommended

View more >