Akira Ct14f9

Colour TV Service Manual

2

Model Group: CT-14FE

CHASSIS: 8803MODEL: CT-14FES1

Model No: CT-14FES1 Version 1.0

3

CONTENTGENERAL DESCRIPTION..................................................................................................................... 4 CONNECTOR VIEW .............................................................................................................................. 5 SAFETY INSTRUCTIONS ..................................................................................................................... 5 CIRCUIT ADJUSTMENTS..................................................................................................................... 6 FAULT FINDING TREES, DIAGRAMS AND OVERVIEWS............................................................ 12 VARIOUS PARAMETERS OF INTEGRATED CIRCUIT .................................................................. 25 THE BUS DATA FOR TMPA8803....................................................................................................... 25 ELECTRICAL PARTS LIST................................................................................................................. 28 CIRCUIT DIAGRAM ............................................................................................................................ 37


4

GENERAL DESCRIPTIONAKTP01 /02 chassis series are applied A14T02/A14T02a respectively which uses mainly TOSHIBA advanced UOC-ultimate chip TMPA8803/8821 and I2C-bus controlled IC With combination of micro controller and small signal processor, the TMPA8803/8821 series feature high-integration, highperformance-to-price ratio and high-reliability and advanced functions with fewer external components, which provide much convenience for manufacturing and technical service. Figure 1: shows the block diagram of AKTP01 (A14T02). Table 1: provides A14T02 mainly ICs and functions. Figure 2: shows the whole set power supply system for AKTP01 (A14T02). Figure 3: shows the system control circuit of AKTP01 (A14T02). Table 1: A14T02 mainly ICs and functions Position N204 N901 N701 N402 N203 Type TMPA8803/23/21 ST24C16-W LA4267 LA78040 LC4053B/CD4053B Function Description Micro controller and small signal processor (UOC) EEPROM Sound power amplifier Vertical scan output stage circuit AV1/AV2 Switch


5

Y IN Cr IN Cb IN VIDEO IN2 AUDIO IN2 VIDEO IN1 AUDIO IN1 VIDEO OUT AUDIO OUT

5 113

AUDIO AMPLIFIER (N701) LA4267

C7007

SP70116

VIDEO or AUDIO AV1/AV2 SWITH (N203)CD4053910 11

14 15

AUDIO IN VIDEO INSIF TRAPS SWICH61 38

SP702 16

212

V202 V201

Z302,Z304

30

24

32

21

19

20

28

HF TUNER A101

IF PRE AMP (V101)

SAWF Z101

IF IN IF IN

41 42

52

B G R

BAND1 V103

BAND2V102

U/V L/H

TOSHIBA

UOC

51 50

1 2 3

TMPA8803/21/2363 58 57 13 16

VIDEO AMPLIFIER V601 V611 V621

CRT

REMOTE INPUT REMOTE RECEIVER A901 MEMORY (N901) ST24C166 5

V.OUT1

FIELD OUTPUT POWER AMP. N402(LA78040)

5

SCREEN

EHT

FOCUS

HEAT

KEY BOARD

HORIZONTAL DRIVE V444AC150-260V50/60Hz

T401

HORIZONTAL OUTPUT V411

FBT(T402) BSC23

POWER SUPPLY Resistance disturbance C501 L502 Bridge rectification VD503-VD506 Filter C507+300V

CIRCUIT V512 V513 V511 T501 VD515

19V 13V 24V 146V 114V


6

SAFETY INSTRUCTIONWARNING: BEFORE EXAMINING AND SERVICING THIS CHASSIS, READ CAREFULLY THE FOLLOWING SAFETY INSTRUCTIONS. X-RAY RADIATION PRECAUTION1. The EHT must be checked every time the receiver is serviced to ensure that the CRT does not emit X-ray radiation as result of excessive EHT voltage. The nominal EHT for this receiver is 22KV at zero beam current (minimum brightness) operating at AC 220V. The maximum EHT voltage permissible in any operating circumstances must not exceed 25KV. When checking the EHT, use the High Voltage Check procedure in this manual using an accurate EHT voltmeter. The only source of X-RAY radiation in this receiver is the CRT. To prevent X-ray radiation, you should use the same type of CRT when replacing it. Some components used in this receiver have safety-related characteristics preventing the CRT from emitting X-ray radiation. For continued safety, replacement component should only be made after referring the Product Safety notice below.

2. 3.

SAFETY PRECAUTION1. The high voltage in the TV reaches to 22KV when the TV is in operation. Be more careful during opening the back cover. a. The high voltage existing in the TV is very dangerous. Refer servicing to qualified personnel only. b. Before removing the high voltage cap. Discharge the anode of the CRT and the chassis in case of electric shock. c. Wear a pair of goggles when handling the CRT to avoid broken pieces damaging your eyes. d. Do not hold the CRT neck in case of causing damage to the CRT. When the power cord needs replacing, use the same one as that provided by AKIRA factory. Voltage exists between the hot and cold ground when TV is in operation. Install a separation transformer during repairing or connecting to any tester for the sake of safety. The power of the separation transformer should be beyond rated overall power. When replacing a burnout fuse, use the one with the same specifications as the original. When replacing old wire, wind new one round the shaft to weld. When replacing components with safety in performance, use the same type as that specified by AKIRA and install it in the former way. Never place wire near high-temperature or high-voltage components.

2. 3. 4. 5. 6.

SAFETY CAUTIONS FOR PRODUCTSMany electric and mechanical components in AKTP01 /02 chassis have special safety performances, which are always neglected. Even if replacing them with some components with the same voltage and power, you can not get effective protection to X-ray. In the circuit diagram, these special electric components are indicated by the special mark ! and on the shadow. When replacing any of them, use the one with the same specifications as the originals. Otherwise, it may cause X-ray radiation and damage to overall safety.


7

CIRCUIT ADJUSTMENTSGENERAL INFORMATIONSAll adjustment are thoroughly checked and corrected when the receiver leaves the factory. Therefore the receiver should operate normally and produce proper color and B/W pictures upon installation. However, several minor adjustments may be required depending on the particular location in which the receiver is operated. This receiver is shipped completely in carton. Carefully draw out the receiver from the carton and remove all packing materials. Power cord into a convenient 220 volts 50 Hz AC two pin power outlet. Turn the receiver ON. Check and adjust all the customer controls such as BRIGHTNESS, CONTRAST and COLOUR Controls to obtain natural color or B/W picture.

AUTOMATIC DEGAUSSINGA degaussing coil is mounted around the picture tube so that external degaussing after moving the receiver is normally unnecessary, providing the receiver is properly degaussed upon installation. The degaussing coil operates for about 1 second after the power to the receiver is switched ON. If the set is moved or faced in a different direction, the power switch must be switched off at least 30 minutes in order that the automatic degaussing circuit operates properly. Should the chassis or parts of the cabinet become magnetized to cause poor color purity, use an external-degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube, the side and front of the receiver and slowly withdraw the coil to a distance of about 2m before disconnecting it from AC source. If color shading still persists, perform the COLOUR PURITY ADJUSTMENT and CONVERGENCE ADJUSTMENTS procedures.

ADJUSTMENT MODEItem Measuring Equipment Preparation Before Adj. B+ adjustment, TV signal receiving AKTP01/02 chassis TV SG (Signal Generator) Digital multi-meter The set is turned on Connect the TV SG to RF input terminal of the set.


8

ADJUSTMENT PROCEDURE1. 2. Turn RP551 potentiometer to adjust B+ to specified voltage. Check voltages for video out, vertical out, circuit work and audio power out as follow:Voltage (volt) 14 inch +B Video Out Vertical Out Circuit Work Audio Power Out 114 145 26 13 19 21 inch 110 188 26 13 19 Tolerance 2V 5V 1V 1V 1V

3.

TV signal receiving a. Press MENU key, to select POS.MEMORY item. Press V+ or V- key, to select SEARCH or AUTOMEMORY item, press P+ key to start searching. b. Press P+ or P- key to inspect the set if there is channel skipped, if so, searching again by SEARCH as above described.

Item Measuring Equipment Preparation before Adj.

TV system adapting & AV in/output inspection AKTP01/02 chassis SG (with NTSC3.58). User remote controller Dual trace oscilloscope Input TV and AV signal


9

Inspection procedure1. 2. 3. 4. Input the TV signal which system is designated in technical specification Switch TV system to the set by pressing SYS key on user remote controller according to the TV system in SG. The picture and sound must be normal. Press TV/AV key, to select AV input. The picture and sound must be normal AV output inspection. Load a 75 resistor to VIDEO output terminal, 1Vp-p video output signal that is from TV signal should be observed on the oscilloscope. Load a 10K resistor to AUDIO output terminal, 0.7Vp-p audio output signal that is from TV should be observed on the oscilloscope. Focus adjustment AKTP01/02 chassis Measuring Equipment Preparation before Adj. SG Brightness, contrast and color should be set in standard

Item

Adjustment procedure1. 2. Receive the cross-hatch pattern signal Turn the focus adjusting VR watching the screen and adjust the vertical line of mark to make the most thin. Then the focus adj. VR is set as close low voltage side as possible. Stop the focus adj. VR at the point that focus is a bit worse at once, turn back to the left and then turn back to the right a little again.

To be fine H. line

V. line Magnified drawing of part


10


White balance adjustment AKTP01/02 chassis SG and white balance meter No.1 service remote controller Warm up the set for more than 30 min. Brightness, contrast and color should be set in standard

Adjustment procedure1. 2. 3. Receive the monoscope pattern signal. Press G (G.DRIVE) key and B (B.DRIVE) key on No.1 service remote controller to select G-DRV and B-DRV respectively, then press + or key to adjust the white balance at the directed value (which is according to the specification of factorys adjustment) Press R+ or R-, G+ or G- and B+ or B- key respectively to adjust the white balance of low light until the white balance of high and low light is good


RF. AGC adjustment AKTP01/02 chassis SG and digital multi meter No.5 service remote controller Connect a digital multi meter to TP101 point on the chassis

Adjustment procedure1. 2. Receive the color bar signal that is 87.5% modulation and 60dBu level Press RF AGC key on No.5 service remote controller to select RF. AGC adjustment, press + or key to adjust the voltage of RF AGC to 6.20.05V that is read on the digital multi meter. Vertical height, linearity and Hor. position adjustment AKTP01/02 chassis Measuring Equipment Preparation before Adj. SG No.2 and No.3 service remote controllers Brightness, contrast and color should be set in standard

Item


11

Adjustment procedure1. 2. Receive the 5-circles pattern signal that is 50HZ vertical frequency Press V-LINE, V-SIZE, V-CENT and H-CENT key on NO.2 service remote controller respectively to select the vertical linearity, height, center (position) and horizontal center (position) adjustment, and then press + or - key to adjust the value of them respectively according to factorys specification. Receive the 5-circles pattern signal that is 60HZ vertical frequency Press V-LINE, V-SIZE, V-CENT and H-CENT key on NO.3 service remote controller separately to adjust the vertical linearity, height, center and horizontal center as above item 3.

3. 4.


OSD position adjustment AKTP01/02 chassis No.1 and No.5 service remote controller Brightness, contrast and color should be set in standard

Adjustment procedure1. 2. Press D-MODE key on No.1 service remote controller to set the set into design mode adjustment Press or key to select OSD item, press or key to adjust the OSD to the center position on the screen or press RF AGC key on No.5 service remote controller and press + or key to adjust the OSD position. Press D-MODE key again to quit design mode adjustment.

3.

Item Measuring Equipment Preparation Before Adj.

The functions of the set inspection TD46 chassis SG User remote controller and No. The set is turned on

Inspection procedure1. 2. 3. 4. 5. 6. 7. Receive the Philips pattern signal. Press PIC key on user remote controller to call the menu as adjusting picture quality. Adjust color, brightness, contrast, sharpness and tint (in NTSC) respectively and all adjustment should be right. Press V+ key to increase the sound volume, no distortion heard at maximum level, press V- key to decrease the sound volume, no sound heard at minimum level. Press POWER key to switch the set into standby status, at mean time the manufactory adjustment mode is cancelled. Press POWER key again, the set should work in normal receiving mode. X (mute), DISP (display), PP and SLEEP key respectively, the relevant function should Press be normal. Press S-OUT key on No.5 service remote controller to set default value that stored in E2PROM on the chassis for product shipment.Model No: CT-14FES1 Version 1.0

12

FAULT FINDING TREE, DIAGRAMS AND OVERVIEW1. Three-None (no raster, no picture, no sound) This failure is mainly caused by big-power circuit such as power supply, horizontal scanning, vertical scanning. The detail checking and repairing steps are as follow.


13

0V 300V

130V Test the voltage of C561 50V 115V Cut off R449 NO variation Test other voltage such as Norma 146V, 24V, and 12V LOW V551,VD551,RP551,V552, VD517,V572,V511 115V N204 pin17 voltage 9V N204 pin13 voltage 2V V444 pin C voltage Check VD556,C561 24V Check R320,V444 Others Check V411 pin C voltage 115V Check T402,V411,R449 Check T402 Check R552,V551,VD551 VD515,V511, V512,R555 Others Check Z901,C901, C902,N204 0V Check VD553,C559, ]R437,C430,T401, C415,V411 0V

Voltage of C507 NO 0V

Check if V501 collect-emitter Was broken down Check the voltage of V501 collector 0V

Check R502,F501,power Swich, AC cord and plug

YES

Check V501,V512,F501,R502,VD503 300V Test voltage of V501 base 0.6V Check T501,VD517, C515,C517,V411, VD552-VD555 C415,C418,T402 C412 0V Check if it get right When cut off V572 YES Test the voltage of N204 pin64

Check T501 1V

115V Recover R449, unplug XZ411 for a While,then test the voltage of C561 No variation Check V501 0V Check V411,T402,T401, Deflection coil

4.5-5.5V CPU has sent the Check if V572 Power-off signal is broken downModel No: CT-14FES1 Version 1.0

Check L414,VD403,C411 Deflection coil

14

2.

B Two-None (no picture, no sound) The failure shows that the set does not display the picture but it has noise wave or blue background or OSD on the screen. This means that the circuits of power supply, horizontal scanning, vertical scanning and video amplification are normal and they are not considered in the repairing. The failures are mainly in the small signal processing circuits. Before checking these circuits, a kind of practical test method is introduced. It is called Signalinput way . The detail is described as follow: We can use the resistance function of an analog multimeter, connect the red pole (negative in ohm scope) on the circuit board ground, then touch softly the test point with another pole (black pole) in ohm scope meanwhile observe the reactivity on the output device. Note : In the TV test, we mainly observe the noise wave on the CRT and listen to the noise voice liking as Ka..Ka from the loudspeakers. a. No picture (see the diagram on next page).


No picture

NO

Check if A101 has input signal YES

Check R553,N904,C926 33V

Out of the 0-33V range

Check RF signal input and adaptor

Check the VT voltage when auto searching In the 0-33V range 0V

The voltage on the C926 33V Check the voltage on the C923 0-33V Check R102, C104, A101 No variation

Check N902, A101

Check the +9V voltage on A101 5V 0V

Check V102,V103,R928,R930, N204,A101 2V Check R119, R213, R101,C101,A101,N204

The voltage between VL and BH vary from 0V to 9V or not when auto searching Check ,V901,N204, R909, R902 ,R903,R913,C912,C908,C909 Exam the voltage of AGC on A101 without antenna 3.8V

0V

Test the voltage on pin 17, 29, 49of N204 9V 0V Check N902, N204, L901,C914, R327,C307, ,L201,C209, C230, L230 YES

Check,L305, C311, L302,C302, L204, C238

Test the voltage on pin 25, 9, 36, 44 of N204 5V

Observe if there is snow-noise-wave disturbance on the CRT via using Signal-input way by touching pin 41 and pin 43 of N204 NO YES Observe if there is snow-noise-wave disturbance on the CRT via using Signal-input way by touching pin 30 of N204 NO Observe if there is snow-noise-wave disturbance on the CRT via using Signal-input way by touching pin 35 of N204 NO Observe if snow-noise-wave disturbance on the CRT via using signal-input way by touching pin 26 of N204 NO Check if voltage on pin 39 of N201 is 1.7V 2V Check C205,A101,N204 Test if there is the sync signal on the pin 12 of N204 NO Check R321,VD436,T402,R462,C452 YES YES YES

Check N902, L302,N204

Check R211,R201,C203,C204

Check V203,V302,L304,Z304,C301

Observe if these is snow-noise-wave disturbance on the CRT via using Signal-input way by touching pin 50,51,52 of N204 NO Check R236,R237,R238,V601,V611,V621,N204

16

b.

No sound In this kind of failure, first of all we should observe if there is the picture on the CRT. It proves the small signal circuit to work correctly with the picture on the CRT and we only check the sound signal processing and sound amplification circuit. The repairing method (B1) may be referred without picture. The detail checking and repairing steps are as follow. Note: Before repairing, assure that the volume is on and the state of set is in TV. Please see the diagram on next page.


17

YES

Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 31 of N204 NO Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 28 of N204 YES

Check R202, C202, N204

NO

Check C103,R706,C703,N204

YES Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 13 of N203 NO Check C292,R293,N203 Check 9V-power supply YES YES 9V Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 12 of N203 Check W214,VD216,R216,R294,N203 YES Check V701,C703, R706 5V NO The voltage on pin 16 of N203 9V

Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 5 of N701 NO The voltage on pin 9 of N701 24V

The voltage on pin 9,10,11of N203

Check VD552,R573,C717,T501,N701

Hear if there is the voice liking KaKa in the loudspeaker via using Signal-input way by touching pin 7 of N701 NO Check SP301, SP302, N701

9V

Check R290,N902, N204


18

c.

Only horizontal line in the middle of the screen If vertical deflection circuit does not work, this kind of failure will happen. In deflection yoke, there only has horizontal sweeping, the electron beam in the CRT only moves in the horizontal orientation, so form this failure. (While checking horizontal and vertical deflection circuit s failure, we have better to use an oscilloscope.) Please see the diagram on next page.


19

Abnormal

The waveform on the pin 16 of N204 Normal The voltage on pin 2 of N402 0V

Check C303,R328,N204

Abnormal

24V Measuring the waveform on pin 1 of N402 Check VD557, R550,V552,N402

Check R328, C446, N402, N204

Normal

The deflection yoke on the CRT Abnormal

Measuring the waveform on pin 5 of N402 Normal

Check N402

Measuring the waveform on the deflection yoke

Abnormal

Check R442,C413,VD433,XZ411, deflection yoke


20

d.

Only vertical line in the middle of the screen This is a dangerous failure. It probable causes flashover and smoking inside the set. Don t let your TV work for a long time as this failure appears. Because the electron beam can not move in the horizontal orientation, the failure should be in the horizontal deflection circuit. We mainly check the open-circuit fault in horizontal deflection circuit. The detail checking and repairing steps are as follow:

Vertical line

The horizontal yoke is opened or not NO Whether XZ411 is opened

YES

Repair CRT

YES

Check if there is bad solder between XZ411, and the main board

NO

Check L414, VD403, C412, C415, especial in inductive components and connector

e.

UOC does not work In television, remote-control system is similar with the computer system. In theory, it can work if it holds two conditions as follow: 1) The power supply: In general, it is 5V, the error is not above 10% and the disturbance pulse is as small as possible. 2) The clock pulse: In TMPA88XX circuit, the clock pulse is generated by pin6 / pin7 of N204 and 8M crystal oscillator. Television s remote-control system also needs reset circuit that can preset the values in internal register. The circuit around pin6 of N204 is called auto-reset circuit. If UOC detects errors in resetting, it will come to the state of programme protected. The detail checking and repairing steps are as follow:


21

N204 does not work 5V NO Observe if there is sine wave on the pin 6 or pin 7 of N204 with an oscilloscope Check Z901, N204 YES 4.98V Check the voltage on the pin 5 of N204 Check N204 Check R941 Check the voltage on the positive pole of C927 =5V Check alternant voltage on secondary coil of T501, 4.98V YES Check T501, VD553,R558 4.98V Check the voltage on the positive pole of VD902 4.98V Check VD902, R947 =3.6V Check R946,R945,V902 NO Check R574,VD922 The voltage on the pin 55 of N204 5V

Check the voltage on the emitter of V902 4.98V


22

f.

No OSD (On Screen Display) This failure is usually cause by the circuit of character generated and located. Most of reasons are that the horizontal and vertical flyback pulse signals do not come to UOC. We can judge this failure by measuring the wave of the character in an oscilloscope. The detail checking and repairing steps are as follow:

No OSD Check the wave on the pin 4 of FBT NO Check FBT T402 Check C452, R462, VD436, R321, N204 YES


23

VARIOUS PARAMETERS OF INTEGRATED CIRCUITA: Pin functions of N204 ( TMPA8803/23/21 ) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Symbol BAND1 BAND2 KEY VSS RESET XIN XOUT TEST VDD VSS VSS FBP in H out HAFC 1 V saw V out HVcc NC Cb in Y in Cr in TV GND C in V2 in TV DVcc V1 in ABCL AU out IF Vcc 9V TV out SIF out Ext AU in H correct/SIF in DC NF PIF PLL IF Vcc 5V Reg Fil Deempha IF AGC IF GND IF in IF in RF AGC TV YC Vcc Monitor out I/O Out Out In In In Out In In In Out Out In In In In In In In Out Out Out In In Out In In Out Function BAND data output 1 BAND data output 2 Key input GND connection Reset signal input 8 MHz oscillator connecting 8 MHz oscillator connecting GND connection 5V power supply GND connection GND connection Input terminal for FBP Output terminal for Horizontal driving pulse Terminal To be connected capacitor for H AFC filter Terminal To be connected capacitor to generate V saw signal Output terminal for Vertical driving pulse Vcc terminal for DEF circuit SECAM Input terminal for Cb signal Input terminal for Y signal Input terminal for Cr signal GND terminal for Digital block Input terminal for Chroma signal Input terminal for Video signal Vcc terminal for Digital block Input terminal for Video signal Input terminal for ABL/ACL control Output terminal for Audio signal Vcc for terminal for IF Circuit Output terminal for detected PIF signal Output terminal for detected SIF signal Input terminal for External Audio signal Input terminal for H correction and SIF Terminal to be connected capacitor for DC Negative Feedback from SIF Det output Terminal to be connected with loop filter for PIF PLL. This terminal voltage is controlled PIF VCO frequency. Vcc terminal for IF circuit. Supply 5V. Terminal to be connected capacitor for stabilizing internal bias. Terminal to be connected capacitor for SIF Det De-Emphasis. Terminal to be connected with IF AGC filter. GND terminal for IF circuit. Input terminals for IF signals. Input terminals for IF signals. Output terminal for RF AGC control level. Vcc terminal for Y/C circuit. Supply 5V. Output terminal for CVBS or Y sihnal selected by BUS(Video SW).


24

Pin 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

Symbol Black Det Chroma PLL IK in RGB Vcc R out G out B out TV AGND VSS VDD VIDEO1/2 SDA1 SCL1 System VT MUTE H.SYNC REMOTE POWER

I/O In Out Out Out In Out I/O I/O Out Out Out In In I/O

Function Terminal to be connected with Black Det filter for black stretch. Terminal to be connected with APC filter for chroma demodulation. Input terminal to sense ACB cathode current. Vcc terminal for RGB circuit. Supply 5V. Output terminal for R signal. Output terminal for G signal. Output terminal for B signal. GND terminal for Analog block. GND connection 5V power supply Video 1 or 2 selection control IIC-BUS SDA1 IIC-BUS SCL1 System VT output Mute Output Horizontal sync signal input Remote controller signal input Power control & Check, On=Hi-Z(input),Off=L(output)

B: Pin functions of N701 ( LA4266/67) Pin 1 2 3 4 5 6 7 8 9 10 Symbol NC NC Filter PRE GND IN NF OUT Power GND VCC NC I/O Function Mute input In Out Sound input Sound output Power supply

C: Pin functions of N402 ( LA78040 ) Pin 1 2 3 4 5 6 7 Symbol V.IN VCC PUMP UP GND V.OUT VCC2 NON INV IN I/O In Function Inverting input Power supply Pump up out Vertical output Output stage VCC Non inv input

Out In


25

THE BUS DATA FOR TMPA8803No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Adjustment Item RCUT GCUT BCUT GDRV BDRV CNTX BRTC COLC TNTC COLP COLS SCOL SCNT CNTC CNTN BRTX BRTN COLX COLN TNTX TNTN ST3 SV3 ST4 SV4 SVD ASSH SHPX SHPN TXCX RGCN ABL DCBS CLTO CLTM CLVO CLVD DEF AKB SECD HPOS VP50 HIT HPS VP60 Adjustment Function Red Dard Balance Green Dark Balance Blue Dark Balance Green light Balance Blue light Balance Sub Contrast Max Sub-bright Centre Sub Color Center(NTSC) Sub Tint Center Sub Color Center(PAL Difference) Sub Color Center(SECAM) Sub Color Sub Contrast Sub Contrast Center Sub Contrast min Sub-bright max(difference) Sub-bright min(difference) Sub color max(difference) Sub color min Sub tint max(difference) Sub tint min(difference) Sub sharp center(3.58NTSC TV) Sub sharp center(3.58NTSC AV) Sub sharp center(OTHER TV) Sub sharp center(OTHER AV) DVD sharp center Factory Data Sub sharpness max(difference) Sub sharpness min(difference) Text RGB contrast max Text RGB contrast min ABL Data A part of Video data in detail The data when TV mode&Sound SYS!=M The data when TV mode&Sound SYS!=M The data when YUV mode&Sound SYS!=M The data when YUV mode&Sound SYS!=M A part of DEF COMP data in detail AKB SYSTEM SECAM mode 0:OFF center 1: ON 35kHz Horizontal center of 50 Hz Vertical centering of 50 Hz Vertical amplitude of 50 Hz Horizontal centering difference of 60 Hz Vertical centering difference of 60 Hz Type Data 5E 72 7D 3B 3E 7F 40 40 40 00 40 07 0B 50 08 35 25 3F 00 28 28 20 20 20 20 26 07 38 15 1F 1F 37 33 0B 4B 4B 4B 01 00 18 0A 06 2C 03 02


26

No 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93

Adjustment Item HITS VLIN VSC VLIS VSS SBY SRY BRTS RAGC HAFC V25 V50 V100 MUTT STAT FLG0 FLG1 REFP RSNS GSNS BSNS MOD STBY SVM VBLK VCEN HSIZ PRBR TRUM ECCT ECCB EHT UCOM PYNX PYNN PYXS PYNS RCUTS GCUTS BCUTS GDRVS BDRVS NOIS AOPT AV OPT OPT2 WAIT TIME CUR CEN

Adjustment Function Vertical amplitude deflection of 60Hz Vertical line of 50 Hz Vertical S correction/50 Hz Vertical line deflection of 60 Hz Vertical S correction/60 Hz SECAM B-Y Black SECAM R-Y Black Sub bright (difference) RF AGC AFC gain Volume 25% Volume 50% Volume 100% Y-MUTE SOFT START CONTORAST UP FOR SOFT START FLAGS FOR IF FLAGS REF Pulse Position R SENS G SENS B SENS Factory Data VCD/IF STANDBY SVM V BLK Start/Stop Factory Data Factory Data Factory Data Factory Data Factory Data Factory Data Factory Data Miciom Control Factory Data Factory Data Factory Data Factory Data FOR YcbCr R CUTOFF FOR YcbCr G CUTOFF FOR YcbCr B CUTOFF FOR YcbCr G DRIVE FOR YcbCr B DRIVE H AFC CONTROL AKB OPTION AV OPTION Factory Data Factory Data Factory Data

Type Data FF 0B 07 00 00 08 08 00 25 09 3D 57 74 00 00 52 04 00 00 00 00 30 00 00 00 27 20 20 10 10 10 24 00 2E 18 22 1E 10 00 10 00 00 01 00 06 3C 57 A0


27

No 94 95 96 97 98 99 100

Adjustment Item CUR STEP AUSTP MODE0 MODE1 OSDF OSD OPT

Adjustment Function Factory Data When Mute off ,Vol.ATT up step number Factory Data Factory Data OSD width OSD position Factory Data

Type Data 02 04 9D 03 53 10 E7

NOTE: The data provided in the form provides to consult only!


28

ELECTRICAL PARTS LISTPRODUCT SAFETY NOTE:Products marked with a ! have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Dont degrade the safety of the product through improper servicing. NOTE: parts that not assigned part numbers() are not available. Tolerance of Capacitors and Resistors are noted with the following symbols. C D F G J K M N Z 0.25% 0.5% 1% 2% 5% 10% 20% 30% +80/-20%

Ref. No R101 R444 R701 R113 R203 R206 R207 R208 R210 R217 R218 R219 R220 R231 R292 R301 R305 R306 R323 R609 W214 R201 R404 R601 R611

Part No. D10B683J-T D10B4R7J-T D10B4R7J-T D10B330J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B101J-T D10B151J-T D10B151J-T D10B151J-T D10B151J-T

Name Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor

Specification RT13-1/6W-68K5% RT13-1/6W-4.75% RT13-1/6W-4.75% RT13-1/6W-335% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1005% RT13-1/6W-1505% RT13-1/6W-1505% RT13-1/6W-1505% RT13-1/6W-1505%


29

Ref. No R621 R106 R107 R310 R205 R236 R237 R238 R325 R326 R240 R320 R941 R241 R517 R704 R604 R614 R624 R119 R214 R324 R603 R613 R623 R902 R904 R925 R115 R480 R578 R608 R610 R944 R946 R242 R708 R202 R230 R330 R108 R249 R251 R446 R916 R928 R930 R945

Part No. D10B151J-T D10B221J-T D10B221J-T D10B221J-T D10B271J-T D10B271J-T D10B271J-T D10B271J-T D10B271J-T D10B271J-T D10B561J-T D10B561J-T D10B561J-T D10B681J-T D10B681J-T D10B751J-T D10B821J-T D10B821J-T D10B821J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B102J-T D10B152J-T D10B152J-T D10B152J-T D10B152J-T D10B152J-T D10B152J-T D10B152J-T D10B222J-T D10B272J-T D10B332J-T D10B332J-T D10B332J-T D10B392J-T D10B392J-T D10B392J-T D10B392J-T D10B392J-T D10B392J-T D10B392J-T D10B472J-T

Name Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor

Specification RT13-1/6W-1505% RT13-1/6W-2205% RT13-1/6W-2205% RT13-1/6W-2205% RT13-1/6W-2705% RT13-1/6W-2705% RT13-1/6W-2705% RT13-1/6W-2705% RT13-1/6W-2705% RT13-1/6W-2705% RT13-1/6W-5605% RT13-1/6W-5605% RT13-1/6W-5605% RT13-1/6W-6805% RT13-1/6W-6805% RT13-1/6W-7505% RT13-1/6W-8205% RT13-1/6W-8205% RT13-1/6W-8205% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1K5% RT13-1/6W-1.5K5% RT13-1/6W-1.5K5% RT13-1/6W-1.5K5% RT13-1/6W-1.5K5% RT13-1/6W-1.5K5% RT13-1/6W-1.5K5% RT13-1/6W-1.5K5% RT13-1/6W-2.2K5% RT13-1/6W-2.7K5% RT13-1/6W-3.3K5% RT13-1/6W-3.3K5% RT13-1/6W-3.3K5% RT13-1/6W-3.9K5% RT13-1/6W-3.9K5% RT13-1/6W-3.9K5% RT13-1/6W-3.9K5% RT13-1/6W-3.9K5% RT13-1/6W-3.9K5% RT13-1/6W-3.9K5% RT13-1/6W-4.7K5%


30

Ref. No R443 R511 R920 R1002 R322 R947 R102 R255 R290 R321 R423 R448 R562 R579 R912 R918 R919 R938 R939 R942 R248 R706 R1003 R213 R216 R293 R328 R447 R607 R7007 R224 R252 R481 R515 R551 R575 R576 R909 R232 R903 R913 R943 R1001 R450 R246 R243 R473 R7003 R233

Part No. D10B562J-T D10B562J-T D10B562J-T D10B562J-T D10B822J-T D10B822J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B103J-T D10B123J-T D10B123J-T D10B123J-T D10B153J-T D10B153J-T D10B153J-T D10B153J-T D10B153J-T D10B153J-T D10B153J-T D10B223J-T D10B223J-T D10B223J-T D10B223J-T D10B223J-T D10B223J-T D10B223J-T D10B223J-T D10B333J-T D10B333J-T D10B333J-T D10B333J-T D10B333J-T D10B473J-T D10B683J-T D10B104J-T D10B104J-T D10B104J-T D10B224J-T

Name Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor

Specification RT13-1/6W-5.6K5% RT13-1/6W-5.6K5% RT13-1/6W-5.6K5% RT13-1/6W-5.6K5% RT13-1/6W-8.2K5% RT13-1/6W-8.2K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-10K5% RT13-1/6W-12K5% RT13-1/6W-12K5% RT13-1/6W-12K5% RT13-1/6W-15K5% RT13-1/6W-15K5% RT13-1/6W-15K5% RT13-1/6W-15K5% RT13-1/6W-15K5% RT13-1/6W-15K5% RT13-1/6W-15K5% RT13-1/6W-22K5% RT13-1/6W-22K5% RT13-1/6W-22K5% RT13-1/6W-22K5% RT13-1/6W-22K5% RT13-1/6W-22K5% RT13-1/6W-22K5% RT13-1/6W-22K5% RT13-1/6W-33K5% RT13-1/6W-33K5% RT13-1/6W-33K5% RT13-1/6W-33K5% RT13-1/6W-33K5% RT13-1/6W-47K5% RT13-1/6W-68K5% RT13-1/6W-100K5% RT13-1/6W-100K5% RT13-1/6W-100K5% RT13-1/6W-220K5%


31

Ref. No R211 R247 R632 R519 R960 R245 R526 R559 R557 R424 R522 R555 R556 R554 R445 R327 R442 R407 R560 R606 R616 R626 R462 R552 R520 R521 R561 R413 R600 R564 R605 R615 R625 R525 R580 R574 R437 R553 R565 R527 R531 ! R558 ! R550 ! R573 ! R449 R502 ! PS551 RP501 C902

Part No. D10B334J-T D10B564J-T D10C330J-T D10C221J-T D10C471J-T D10C182J-T D10C222J-T D10C392J-T D10C472J-T D10C153J-T D10C153J-T D10C473J-T D10C473J-T D10C154J-T D10D1R8J-T D10D221J-T D10D331J-T D10D102J-T D10D332J-T D10D332J-T D10D332J-T D10D332J-T D10D682J-T D10D473J-T D10D104J-T D10D104J-T D10D224J-T S10E472J-S(A) S10F1R0J-C S10E471J-C S10E123J-C S10E123J-C S10E123J-C S10F680J-C S10F680J-C S10F151J-C S10F271J-C S10F123J-C S10F123J-C S10G560J-C F10DR47J-C F10D1R0J-C F10D1R0J-C W11H3R9K W10J3R9K P10X180J-C V11D202B C2CF200J-T

Name Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Carbon resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Metal oxide resistor Glass-Glazed Fixed RES Fuse resistor Fuse resistor Fuse resistor Wire-wound resistor Wire-wound resistor Thermistor Potentiometer Ceramic capacitor

Specification RT13-1/6W-330K5% RT13-1/6W-560K5% RT14-1/4W-335% RT14-1/4W-2205% RT14-1/4W-4705% RT14-1/4W-1.8K5% RT14-1/4W-2.2K5% RT14-1/4W-3.9K5% RT14-1/4W-4.7K5% RT14-1/4W-15K5% RT14-1/4W-15K5% RT14-1/4W-47K5% RT14-1/4W-47K5% RT14-1/4W-150K5% RT15-1/2W-1.85% RT15-1/2W-2205% RT15-1/2W-3305% RT15-1/2W-1K5% RT15-1/2W-3.3K5% RT15-1/2W-3.3K5% RT15-1/2W-3.3K5% RT15-1/2W-3.3K5% RT15-1/2W-6.8K5% RT15-1/2W-47K5% RT15-1/2W-100K5% RT15-1/2W-100K5% RT15-1/2W-220K5% RY16/RY21-1W-4.7K5% RY17/RY21-2W-2.25% RY16/RY21-1W-4705% RY16/RY21-1W-12K5% RY16/RY21-1W-12K5% RY16/RY21-1W-12K5% RY17/RY21-2W-685% RY17/RY21-2W-685% RY17/RY21-2W-1505% RY17/RY21-2W-2705% RY17/RY21-2W-12K5% RY17/RY21-2W-12K5% RY18/RY21-3W-565% RI40-1/2W-24M5% RF10-1/2W-0.475% RF10-1/2W-15% RF10-1/2W-15% RXG6-5W-3.9-J RXG6-6W-3.9-J PTC-180HM WI06-2AA2K CC1-06A-CH-50/63V-20pF-J


32

Ref. No C315 C247 C901 C602 C612 C622 C235 C908 C909 C912 C203 C934 C246 C234 C112 C113 C114 C120 C202 C208 C210 C211 C232 C233 C304 C309 C310 C574 C604 C903 C913 C915 C924 C929 C930 C402 C403 C452 C448 C503 C504 C505 C506 C555 C556 C418 VD530 C630 C535 !

Part No. C2CF220J-T C2CF330J-T C2CF330J-T C2BF101K-T C2BF101K-T C2BF101K-T C2BF181K-T C2BF221K-T C2BF221K-T C2BF221K-T C2BF102K-T C2BF102K-T C2BF152K-T C2BF272K-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2FF103Z-T C2BP102K-T C2BP392K-T C2BP392K-T C2SP100D-T C2BW102K-O C2BW102K-O C2BW102K-O C2BW102K-O C2BW471K-O C2RX221K-O C2RX471K-O C2RX681K-O C2EX222Z-O C2EM102M-O

Name Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor Ceramic capacitor

Specification CC1-06A-CH-50/63V-22pF-J CC1-06A-CH-50/63V-33pF-J CC1-06A-CH-50/63V-33pF-J CC1-06A-RH-50/63V-100pF-J CC1-06A-RH-50/63V-100pF-J CC1-06A-RH-50/63V-100pF-J CC1-06A-RH-50/63V-180pF-J CC1-06A-RH-50/63V-220pF-J CC1-06A-RH-50/63V-220pF-J CC1-06A-RH-50/63V-220pF-J CT1-06A-2B4-50/63V-1000pF-K CT1-06A-2B4-50/63V-1000pF-K CT1-06A-2B4-50/63V-1500pF-K CT1-06A-2B4-50/63V-2700pF-K CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08A-2F4-50/63V-0.01uF-Z CT1-08C-2B4-500V-1000pF-K CT1-08C-2B4-500V-3900pF-K CT1-08C-2B4-500V-3900pF-K CT1-07-B-500V-10PF-10% CT81-08C-2R-1KV-1000pF-K CT81-08C-2R-1KV-1000pF-K CT81-08C-2R-1KV-1000pF-K CT81-08C-2R-1KV-1000pF-K CT81-08C-2R-1KV-470pF-K CT81-08C-2R-2KV-220pF-K CT81-08C-2R-2KV-470pF-K CT81-08C-2R-2KV-680pF-K CT81-08C-2R-2KV-2200pF-K CTJ1-AC250V-1000PF-20%


33

Ref. No C291 C292 C296 C293 C294 C306 C558 C603 C605 C218 C102 C238 C240 C244 C295 C307 C914 C916 C920 C230 C243 C302 C702 C704 C927 C928 C209 C222 C311 C571 C201 C700 C557 C564 C717 C433 C430 C449 C559 C565 C104 C237 C108 C110 C204 C301 C303 C308 C205

Part No. E20C4R7M-T E20C4R7M-T E20C4R7M-T E20C100M-T E20C100M-T E20C100M-T E20C100M-T E20C100M-T E20C100M-T E20C220M-T E20C470M-T E20C470M-T E20C470M-T E20C470M-T E20C470M-T E20C470M-T E20C470M-T E20C470M-T E20C470M-T E20C101M-T E20C101M-T E20C101M-T E20C101M-T E20C101M-T E20C101M-T E20C101M-T E20C471M-T E20C471M-T E20C471M-T E20C471M-T E20D100MN-T E20D221M E20D471M E20D471M E20D471M E20D102M E20E470M-T E20E101M-T E20E331M E20E331M E20F0R1MR E20FR22M-T E20FR47M-T E20FR47M-T E20FR47M-T E20FR47M-T E20FR47M-T E20FR47M-T E20F1R0M-T

Name Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor NON-POLAR Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor

Specification CD110-16V-4.7uF M CD110-16V-4.7uF M CD110-16V-4.7uF -M CD110-16V-10uF M CD110-16V-10uF M CD110-16V-10uF M CD110-16V-10uF M CD110-16V-10uF M CD110-16V-10uF -M CD110-16V-22uF -M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF M CD110-16V-47uF -M CD110-16V-100uF M CD110-16V-100uF M CD110-16V-100uF M CD110-16V-100uF M CD110-16V-100uF M CD110-16V-100uF M CD110-16V-100uF M CD110-16V-470uF M CD110-16V-470uF M CD110-16V-470uF M CD110-16V-470uF -M CD71-BP-25V-10uF-M CD110-25V-220uF -M CD110-25V-470uF M CD110-25V-470uF M CD110-25V-470uF -M CD110-25V-1000uF -M CD110-35V-47uF -M CD110-35V-100uF -M CD110-35V-330uF -M CD110-35V-330uF -M CD114-50V-0.1uF -M CD110-50V-0.22uF -M CD110-50V-0.47uF M CD110-50V-0.47uF M CD110-50V-0.47uF M CD110-50V-0.47uF M CD110-50V-0.47uF M CD110-50V-0.47uF -M CD110-50V-1uF M


34

Ref. No C215 C216 C217 C236 C245 C103 C300 C443 C926 C101 C206 C703 C705 C411 C563 C562 C507 C231 C446 C708 C305 C515 C517 C514 C447 C460 C461 C701 C922 C923 C413 C421 C444 C412 C415 ! C501 ! L414 T101 L103 L304 L101 L104 L201 L230 L302 L305 L901 L501 ! VD515 !

Part No. E20F1R0M-T E20F1R0M-T E20F1R0M-T E20F1R0M-T E20F1R0M-T E20F2R2M-T E20F2R2M-T E20F2R2M-T E20F2R2M-T E20F4R7M-T E20F4R7M-T E20F4R7M-T E20F4R7M-T E21H1R0M-T E20H101M E20H100M E20M101M F20F102J-T F20F222J-T F20F392J-T F20F822J-T F22F123J-T F20F223K-T F20F393K-T F20F563K-T F20F104K-T F20F104K-T F20F104K-T F20F104K-T F20F104K-T F20G104K-T F20G104K-T F20G104K-T F20J474J F20Z822J F20R224M LXXX0040 TLXX0018 L3X11R0K-T L3X18R2K-T L3X1150K-T L3X1150K-T L3X1150K-T L3X1150K-T L3X1150K-T L3X1150K-T L3X1150K-T LMXX0002 RX0001XX

Name Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Electrolytic Capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Mylar capacitor Polypropylene capacitor Polypropylene capacitor Polypropylene capacitor H-linear Coil Inductor Inductor Inductor Inductor Inductor Inductor Inductor Inductor Inductor Degaussing coil Photoelectricity coupler

Specification CD110-50V-1uF M CD110-50V-1uF M CD110-50V-1uF M CD110-50V-1uF M CD110-50V-1uF -M CD110-50V-2.2uF M CD110-50V-2.2uF M CD110-50V-2.2uF M CD110-50V-2.2uF -M CD110-50V-4.7uF M CD110-50V-4.7uF M CD110-50V-4.7uF M CD110-50V-4.7uF -M CD110-160V-1uF -M CD110-160V-100uF-M CD110-160V-10uF -M CD293-400V-100uF-10% CL11-50V/63V-1000PF-K CL11-50V/63V-2200PF-K CL11-50V/63V-3900PF-K CL11-50V/63V-8200PF-K CL21X-50V/63V-0.012uF-K CL11-50V/63V-0.022uF-K CL11-50V/63V-0.039uF-K CL11-50V/63V-0.056uF-K CL11-50V/63V-0.1uF-K CL11-50V/63V-0.1uF-K CL11-50V/63V-0.1uF-K CL11-50V/63V-0.1uF-K CL11-50V/63V-0.1uF-K CL11-100V-0.1uF-K CL11-100V-0.1uF-K CL11-100V-0.1uF-K CBB21-200V-0.47uF5% CBB81-1.6KV-8200PF-J CBB62-250VAC-0.22uF LX40 D18 LGA0307-1uH-K LGA0307-8.2uH-K LGA0307-15uH-K LGA0307-15uH-K LGA0307-15uH-K LGA0307-15uH-K LGA0307-15uH-K LGA0307-15uH-K LGA0307-15uH-K PC817B/C


35

Ref. No VD1001 VD230 VD232 VD233 VD401 VD514 VD516 VD558 VD601 VD901 VD517 VD552 VD553 VD557 VD433 VD434 VD403 VD503 VD504 VD505 VD506 VD556 VD554 VD555 VD551 VD922 VD501 VD902 VD921 VD216 VD217 VD703 VD436 N904 N701 N902 N203 N204 N402 N901 V230 V232 V233 V302 V511 V602 V902 V570

Part No. DL0008XX DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T DR0001XX-T DR0003XX-T DR0003XX-T DR0003XX-T DR0003XX-T DR0009XX-T DR0009XX-T DR0010XX-T DR0015XX-T DR0015XX-T DR0015XX-T DR0015XX-T DR0017XX DR0018XX DR0031XX-T DZ0001XX-T DZ0002XX-T DZ0006XX-T DZ0006XX-T DZ0015XX-T DZ0011XX-T DZ0011XX-T DZ0011XX-T DZ0004XX-T IXXX0080 IXXX0180 IXXX0118 IXXX0120 IXXX0142 IXXX0173 RXA1015X-T RXA1015X-T RXA1015X-T RXA1015X-T RXA1015X-T RXA1015X-T RXA1015X-T RXB764XX-T

Name LED Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode IC IC IC IC IC IC IC Audion Audion Audion Audion Audion Audion Audion Audion

Specification RED 5mm IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A IS1555/IN4148A FR105 FR105 FR105 FR105 GP10D/FR104/IN4004 GP10D/FR104/IN4004 FR107 TVR4N/TRM11C TVR4N/TRM11C TVR4N/TRM11C TVR4N/TRM11C RGP10J RGP10D TJ1010 RD6.2EB3/HZ7A1 RD5.1EB2/HZ5C1 RD3.6L/HZ4A2 RD3.6L/HZ4A2 RD5.6EB2/HZ6B1 RD9.1EB2/HZ9B2 RD9.1EB2/HZ9B2 RD9.1EB2/HZ9B2 RD10EB2/HZ11C1 upc574J/CW574 LA4267 5W TA78M09 9V LC4053B/CD4053B TMPA8803CPAN-3GV1 LA78040 BR ST24C16-W 2SA1015Y/2SA608/2SA733Q 2SA1015Y/2SA608/2SA733Q 2SA1015Y/2SA608/2SA733Q 2SA1015Y/2SA608/2SA733Q 2SA1015Y/2SA608/2SA733Q 2SA1015Y/2SA608/2SA733Q 2SA1015Y/2SA608/2SA733Q 2SB764


36

Ref. No V552 V101 V601 V611 V621 V444 V512 V501 V102 V103 V201 V202 V203 V231 V551 V571 V572 V701 V901 V411 V905 Z304 Z302 Z101 F501 ! A1001 A101 SW1001 SW1002 SW1003 SW1004 SW1005 SW1006 Z901

Part No. RXB892XX-T RXC2216X-T RXC2482X RXC2482X RXC2482X RXC2383X-T RXC3807X RXC5287X RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXC945XX-T RXD2499X RXD400XX-T FC0007XX FC0008XX FXXX0020 RXXX0016 T9XX0330C KXXX0101 KXXX0101 KXXX0101 KXXX0101 KXXX0101 KXXX0101 XC0004XX-A FXXX0020

Name Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Audion Ceramic trap filter Ceramic trap filter SAWF FUSE Remote receiver Tuner Touch switch Touch switch Touch switch Touch switch Touch switch Touch switch XTLO IRICO

Specification 2SB892/2SB985T 2SC2216 2SC2482 2SC2482 2SC2482 2SC2383-O 2SC3807/2SC5070 2SD1710/2SC4584/C5586 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SC945/2SC1815/2SC536E 2SD2499/2SD1651 2SD400D XT6.0M XT5.5M 1339 38.9M 2.5A 250V HS0038 TDV-3S7-9 470M PUSH SW.(L:5mm) PUSH SW.(L:5mm) PUSH SW.(L:5mm) PUSH SW.(L:5mm) PUSH SW.(L:5mm) PUSH SW.(L:5mm) 8.0M(20P) 37SX110Y22-DC05


Circuit diagram

Documents

Akira Ct14f9