Upload
synscon
View
214
Download
0
Embed Size (px)
DESCRIPTION
Maximum Recovered I.D. Expanded Wall Thickness Minimum Expanded I.D. Minimum Expanded I.D. HLF-19 HLF-23 HLF-33 HLF-42 HLF-48 HLF-54 HLF-58 HLF-66 HLF-72 HLF-83 HLF-92 HLF-103 HLF-112 HLF-161 inches mm Std. Spools HTIMconsists of an outer layer of PTFE heat shrink with an inner layer of FEP tubing. When properly heated, the PTFE shrinks tightly over the substrate and the FEP melts to encapsulate the product, providing a tight, moisture resistant seal. Catalog Number Catalog Number 15
Citation preview
HEAT SHRINKABLE PTFE WITHMELTABLE FEP LINER
HTIM consists of an outer layer of PTFE heatshrink with an inner layer of FEP tubing. Whenproperly heated, the PTFE shrinks tightly over thesubstrate and the FEP melts to encapsulate theproduct, providing a tight, moisture resistant seal.
Operating Temperature Range:Shrink Ratio:
Shrink Temperature:Recommended Heat Gun:
Standard Colors:Standard Shipping Length:
0.0040.0050.0180.0210.0250.0310.0420.0910.1310.178
0.0060.0070.0270.0310.0370.0460.0620.1350.1950.265
0.023 +/- 0.0050.028 +/- 0.0050.032 +/- 0.0050.032 +/- 0.0050.035 +/- 0.0050.035 +/- 0.0050.035 +/- 0.0050.055 +/- 0.0050.055 +/- 0.0050.065 +/- 0.005
0.584 +/- 0.1270.711 +/- 0.8130.813 +/- 0.1270.813 +/- 0.1270.889 +/- 0.1270.889 +/- 0.1270.889 +/- 0.1271.400 +/- 0.1271.400 +/- 0.1271.650 +/- 0.127
ApproximateWeight
HTIM-1/32HTIM-1/16HTIM-1/8HTIM-5/32HTIM-3/16HTIM-1/4HTIM-3/8HTIM-1/2HTIM-3/4HTIM-1”
MinimumExpanded I.D.
ExpandedWall Thickness
CatalogNumber
MaximumRecovered I.D.
0.0000.0000.0000.0000.0620.1250.1900.3120.4400.680
0.000.000.000.001.573.184.837.92
11.1817.27
0.0360.0600.1300.1600.1900.2500.3500.4500.7000.950
0.911.523.304.064.836.358.89
11.4317.7824.13
inches mmSize inches mm inches mm lb/ft kg/m
-100°F (-73°C) to 450°F (232°C)See table below680°F (360°C)750°F (400°C)Translucent to Opaque4 Foot Lengths
HEAT SHRINKABLE LAYFLAT PVC
HLF PVC heat-shrink tubing is a thin-wall, low-cost materialoffering good electrical and mechanical characteristics. Thisspecially formulated polyvinyl chloride material will shrink rapid-ly and uniformly, conforming to the shape of the object to becovered. Applications include wire and cable identification,insulation, and jacketing of capacitors or similar objects whereprotective covering is required. Widely used to hold groups ofbatteries together to form “battery packs.”
HLF is available with a 0.004” (0.010 mm) or 0.006” (0.015mm) wall thickness - please specify when ordering.
Operating Temperature Range:Shrink Ratio:
Shrink Temperature:Recommended Heat Gun:
Standard Colors:Standard Shipping Length:
-4°F (-20°C) to 212°F (100°C)2 to 1275°F (135°C)500°F (260°C)White, Black, or ClearSpooled
HLF-19HLF-23HLF-33HLF-42HLF-48HLF-54HLF-58HLF-66HLF-72HLF-83HLF-92HLF-103HLF-112HLF-161
MinimumExpanded I.D.
CatalogNumber
0.7480.9061.3001.6541.8902.1262.2832.5982.8353.2683.6224.0554.4096.339
19.0023.0033.0042.0048.0054.0058.0066.0072.0083.0092.00
103.00112.00161.00
inches mm
Std.Spoolsft / spoolSize
50, 25050, 25050, 25050, 25050, 25050, 25050, 25050, 25050, 25050, 25050, 25050, 25050, 25050, 250
Other sizes and colors available - subject to factoryminimums.
SEMI-RIGID · THIN-WALL (0.004”, 0.006”) · 2:1
15
HTIM
HLF