26610016 Latitude Nerf Bar for F-150 Super Crew 2019. 1. 31.¢  Latitude Nerf Bar for F-150 Super Crew

  • View
    0

  • Download
    0

Embed Size (px)

Text of 26610016 Latitude Nerf Bar for F-150 Super Crew 2019. 1. 31.¢  Latitude Nerf Bar for F-150...

  • Page 1 of 5

    Installation Instructions I - Sheet Number LUNDRB25 Rev.A

    Important Safety Information

    NOTE: Actual product may vary from illustration. Contents

    Latitude Nerf Bar for F-150 Super Crew For proper installation and best possible fit, please read all instructions BEFORE you begin.

    For technical assistance or to obtain missing parts, please call Customer Relations at 1-800-241-7219.

    • To be used with Lund® branded products only. • Do not stand on Lund running board or bracket while vehicle is in motion. • Do not use the brackets as a jacking point for the vehicle. • Do not use the bracket system or running boards to fasten cargo. • Periodically check all components for tightness. • Be sure to wear safety glasses while installing brackets. •When using power tools, read and understand all operating instructions.

    Tools Required

    Preparation Before Installation • Park your vehicle in a clean, level location. Check to make sure the vehicle is in park, or for manual drive models, place the transmission in first gear. Engage the parking brake. Chock wheels. • Unpack the kit and identify the parts according to the content descriptions. • An assistant is recommended to help position the running board properly during the installation.

    Socket Set Wheel Chocks Safety GlassesRatchet and Extension

    Lund Part# 26510016 26610016

    Passenger Side Nerf Bar

    Driver Front Bracket Passenger Front Bracket

    Passenger Mid Bracket

    Passenger Rear BracketDriver Rear Bracket

    Driver Mid Bracket

    12mm Single Bolt Plate (2)

    12mm Double Bolt Plate (2)

    12mm Plastic Retainers (6)

    8mm x 30 mm hex bolt (16)

    8mm x 25 mm hex bolt (12)

    8mm x 24mm OD x 2mm Flat Washer (36)

    8mm Lock Washer (28)

    8mm Hex Nut (8)

    12mm flat washer (6)

    12mm lock washer (6)

    12mm hex nuts (6)

    8mm clip nuts (8)

    Driver Side Nerf Bar

  • 3

    2

    Page 2 of 5

    1

    Installation Steps NOTE: Actual application may vary slightly from illustrations.

    Locate the driver side front Mounting Bracket. Attach the Mounting Bracket to the Bolt Plate with (1) 12mm Flat Washer, (1) 12mm Lock Washer and (1) 12mm Hex Nut. Line up the two holes in the Mounting Bracket with

    the previously installed Nut Clips and secure with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers. Do not tighten hardware at this time.

    Starting at the driver side-front of the vehicle, locate the round and rectangular openings in the inner body panel. NOTE: Mounting holes may be covered with rubber grommet and/or sealing tape. Remove to uncover mounting locations. Insert (2) 8mm Clip Nuts, (with the nut portion to the inside), into the rectangular opening and line up the threaded nut with the factory round holes. Next, partially thread (1) 12mm Plastic Retainer onto (1) 12mm Bolt Plate, and insert the Bolt Plate

    into the large round hole. Once inserted, thread the Plastic Retainer onto the Bolt Plate until it is tight against the body panel. NOTE: When properly installed, the Plastic Retainer is designed to prevent the Bolt Plate from falling into the body

    cavity during Bracket installation. (Figure 1).

    Align the clip nuts with the two round holes

    Remove the rubber grommet / sealing tape covering this hole

    Bolt Plate

    Plastic Retainer

    Figure 1

    Figure 2

    Figure 3

    Front

    Front

    Front

    Line up the two holes in the bottom of the Mounting Bracket with the factory holes in the pinch weld. Attach the Mounting Bracket to the pinch weld using the included (2) 8mm x 30mm Hex Bolts, (2) 8mm Flat Washers. Insert the Hex Bolt with

    the Flat Washer up, from the outside-in. Secure with (2) 8mm Flat Washers, (2) 8mm Flat Washers, and (2) 8mm Hex Nuts, (Figure 3). Snug all hardware but do not tighten at this time.

    (1) 12mm Flat Washer (1) 12mm Lock Washer (1) 12mm Hex Nut

    (2) 8mm Hex Bolt (2) 8mm Flat Washer

    (2) 8mm Hex Bolt (2) 8mm Lock Washer (2) 8mm Flat Washer

    (2) 8mm Flat Washer (2) 8mm Lock Washer (2) 8mm Hex Nut

  • Page 3 of 5

    Installation Steps NOTE: Actual application may vary slightly from illustrations.

    4

    5

    6

    Figure 5

    Figure 4

    Figure 6

    Starting at the driver side-middle of the vehicle, locate the round and rectangular openings in the inner body panel. NOTE: Mounting holes may be covered with rubber grommet and/or sealing tape. Remove to uncover mounting

    locations. Insert (2) 8mm Clip Nuts, (with the nut portion to the inside), into the rectangular opening and line up the threaded nut with the factory round holes. (Figure 4).

    Locate the driver side middle Mounting Bracket. Line up the two holes in the Mounting Bracket with the previously installed Nut Clips and secure with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers. (Figure 5)

    Front

    Line up the two holes in the bottom of the Mounting Bracket with the factory holes in the pinch weld. Attach the Mounting Bracket to the pinch weld using the included (2) 8mm x 30mm Hex Bolts, (2) 8mm Flat Washers. Insert the Hex Bolt with

    the Flat Washer up, from the outside-in. Secure with (2) 8mm Flat Washers, (2) 8mm Flat Washers, and (2) 8mm Hex Nuts, (Figure 3). Snug all hardware but do not tighten at this time.

    (2) 8mm Hex Bolt (2) 8mm Flat Washer

    (2) 8mm Flat Washer (2) 8mm Lock Washer (2) 8mm Hex Nut

  • Page 4 of 5

    Installation Steps NOTE: Actual application may vary slightly from illustrations.

    7

    8

    9 10

    Figure 8

    Figure 7

    Locate the driver side rear Mounting Bracket. Attach the Mounting Bracket to the Bolt Plate with (2) 12mm Flat Washer, (2) 12mm Lock Washer and (2) 12mm Hex Nut. Do not tighten hardware at this time.

    Front

    (2) 12mm Flat Washer (2) 12mm Lock Washer (2) 12mm Hex Nut

    Bolt, lock washer, and flat washer

    Nerf bar

    Figure 9 Figure 10

    Moving to the rear, locate the factory large round hole and smaller oval hole in the inner body panel. NOTE: Mount- ing holes may be covered with rubber grommet, insulation or sealing tape. Uncover mounting locations. Select (1) 12mm Double Bolt Plate and insert it into the larger round opening and out the smaller oval hole. Next, thread (2)

    12mm Plastic Retainer onto the threaded end. Thread the Retainers all of the way down until tight against the sheet metal. (Figure 7)

    Align the passenger side nerf bar with the driver side front mounting bracket and loosely attach using (2) 8mm x 25mm bolts, (2) 8mm lock washers, and

    (2) 8mm x 24 mm flat washers. (Figure 9)

    Repeat Step 9 to attach the nerf bar at the middle and rear bracket locations. (Figure 10)

  • Page 5 of 5

    Installation Steps NOTE: Actual application may vary slightly from illustrations.

    11

    12 Inspection After Installation

    Care and Cleaning

    Congratulations!

    © 2014 Lund International, Inc. All rights reserved. Lund® and the Lund® logo are trademarks of Lund International, Inc.

    Lund International 800-241-7219 • Visit us at lundinternational.com

    Figure 11

    Figure 12

    • Inspect all bolts and nuts for proper tightness.

    • Wash only with mild soap & dry with a clean cloth. • Do not use cleaning solvents of any kind.

    You have purchased one of the many quality Lund® branded products offered by Lund International, Inc. We take the utmost pride in our products and want you to enjoy years of satisfaction from your investment. We have made every effort to ensure that your product is top quality in terms of fit, durability, finish and ease of installation.

    Rotate bar until step pad surface is level. and tighten all hardware. Repeat steps 2 – 6 for driver Sidebar installation. (Figure 12)

    Check position of nerf board and ensure it is properly parallel with rocker panel. Adjust as needed. (Figure 11)

    Fully tighten all bracket bolts and nuts.

  • REMARQUE : le produit réel peut différer du modèle illustré. Contenu

    Outils nécessaires

    Jeu de douilles Cales Lunettes de protection Clé à cliquet et pièce

    de prolongement

    Barre nerf côté passager

    Support avant côté conducteur Support avant côté passager

    Support central côté passager

    Support arrière côté passager

    Support arrière côté conducteur

    Support central côté conducteur

    Plaque de boulon unique de 12 mm (2)

    Plaque de boulon double de 12 mm (2)

    Attaches en plastique de 12 mm (6)

    Boulon à tête hexagonale de

    8 mm x 30 mm (16)

    Boulon à tête hexagonale de

    8 mm x 25 mm (12)

    Rondelle plate DE de 8 mm x 24 mm x 2 mm

    (36)

    Rondelle de blocage de 8 mm

    (28)

    Écrou à tête hexagonale de

    8 mm (8)

    Rondelle plate de 12 mm (6)

    Rondelle de blocage de 12 mm (6)

    Écrous à tête hexagonale de

    12 mm (6)

    Écrous de collier de 8 mm (8)

    Barre nerf côté conducteur

    Veuillez lire l'ensemble des instructions AVANT d'utiliser le produit afin de garantir une installation correcte et un ajustement optimal. Pour obtenir une assistance technique ou demander des pièces manquantes, veuillez appeler le service clientèle au 1-800 241-7219.

    Instructions d'i