Embed Size (px)
Citation preview
WAN Acceleration SonicWALL WXA 5000 Getting Started Guide
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
Contents Registering your SonicWALL WXA 5000 Virtual Appliance ................................................................................... 2
Creating a MySonicWALL Account ................................................................................................................... 2 Registering the WXA 5000 Serial Number ........................................................................................................ 3 Associating the WXA 5000 Virtual Appliance (Optional) .................................................................................... 4 Activating the WXA 5000 License ..................................................................................................................... 6
Choosing a Network Deployment Mode ............................................................................................................... 9 Direct Access Mode ......................................................................................................................................... 9 VLAN Trunks Mode ........................................................................................................................................ 10 NSA/TZ Trunking Mode .................................................................................................................................. 11
Installing the WXA 5000 using VMware vSphere ................................................................................................ 12
Introduction The SonicWALL WXA 5000 Virtual Appliance reduces application latency and conserves bandwidth, significantly enhancing WAN application performance. This Getting Started Guide details the deployment of the SonicWALL WXA 5000 Virtual Appliance.
Requirements The SonicWALL WXA 5000 requires:
• A SonicWALL E-class NSA, NSA, or TZ security appliance running SonicOS 5.8.1 or higher firmware. • An unused interface on the SonicWALL NSA or TZ security appliance. • A VMware ESX or ESXi Server running 4.0 or higher with:
o 2 virtual CPUs o 80 GB hard disk o 4GB RAM
• A layer 2 network between the ESX Server and the SonicWALL NSA/TZ. Note: This is required for communication between SonicWALL WXA 5000 on your ESX Server and SonicWALL appliance.
Customers with current service/software support contracts can obtain updated versions of SonicWALL firmware from the MySonicWALL customer portal at https://www.mysonicwall.com. Updated firmware is also available for free within 90 days of registering the SonicWALL device on MySonicWALL.
2
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
Registering your SonicWALL WXA 5000 Virtual Appliance You must register your SonicWALL WXA 5000 Virtual Appliance before first use. Registration is performed using the NSA/TZ appliance management interface. It is recommended that you also associate your WXA 5000 Virtual Appliance as a child to the managing NSA/TZ appliance. When registration is completed, the SonicWALL WXA appliance will be licensed and ready to use. This section contains the following subsections: Creating a MySonicWALL Account ...................................................................................................................... 2 Registering the WXA 5000 Serial Number............................................................................................................ 3 Associating the 5000 Virtual Appliance (Optional) ................................................................................................ 4 Activating the WXA 5000 License ........................................................................................................................ 6
Creating a MySonicWALL Account A MySonicWALL account is required for product registration. If you already have an account, continue to the Registering, Associating, and licensing the WXA 5000 sections. Perform the following steps to create a MySonicWALL account:
1. In your web browser, navigate to http://www.mysonicwall.com. 2. In the login screen, click the Not a registered user? Register Now link.
3. Complete the registration form, click the Register link. 4. Verify the information you entered is correct, click the Submit button. 5. In the confirmation screen, click the continue button.
3
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
Registering the WXA 5000 Serial Number To register your SonicWALL WXA 5000 Virtual Appliance, perform the following steps: 1. Log in to your http://www.mysonicwall.com account.
2. Navigate to the My Products > Register Product page.
3. Enter you Serial Number, Friendly Name, Product Group, and Authentication Code. 4. Click the Submit button.
You have successfully registered your SonicWALL WXA 5000 Virtual Appliance.
4
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
Associating the WXA 5000 Virtual Appliance (Optional) To associate your SonicWALL WXA 5000 Virtual Appliance as a child to your NSA/TZ appliance, perform the following steps:
Note: Associating your WXA 5000 Virtual Appliance with the managing NSA/TZ appliance is recommended, but not required.
1. Log in to your http://www.mysonicwall.com account.
2. Navigate to the My Products > Product Management page.
3. Click on the NSA/TZ appliance you are using to manage the SonicWALL WXA appliance.
5
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
The “Service Management” page displays:
4. Under the Associated Products section, click the WAN Acceleration link.
The “My Product > Associated Products” page displays:
5. In the Serial Number drop-down list, select the serial number for the WXA 5000 Virtual Appliance. 6. Click the Associate button.
Your SonicWALL WXA 5000 Virtual Appliance is now associated with the managing NSA/TZ appliance.
6
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
Activating the WXA 5000 License To activate your SonicWALL WXA 5000 Virtual Appliance license, perform the following steps:
1. Log in to your SonicWALL NSA/TZ appliance. 2. Navigate to the System > License page. 3. Click the click here link to activate, upgrade, or renew services.
The License Management page displays:
4. Enter your MySonicWALL.com account Email Address or Username and Password in the appropriate fields,
click the Submit button.
7
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
The MySonicWALL.com home page displays:
5. Enter the Activation Key or Serial Number in the textbox, then click the Next button.
The registered products populate:
6. If you have multiple NSA/TZ appliances registered, select the one you are using with your WXA appliance.
The Activate Service page displays:
7. Enter the Activation Key(s), then click the Submit button.
8
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
The confirmation page displays.
You have successfully licensed your SonicWALL WXA 5000 Virtual Appliance.
8. Before accessing the WAN Acceleration page, navigate to the System > Licenses page and click the Synchronize button. This synchronizes the licenses between the License Manager and NSA/TZ appliance.
9
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
Choosing a Network Deployment Mode Choose a network deployment mode for communication between the SonicWALL WXA 5000 on your ESX Server and the SonicWALL NSA or TZ security appliance. The following is a list of the possible modes:
• Direct Access Mode • VLAN Trunks Mode • NSA/TZ Trunking Mode
Please refer to http://www.vmware.com/pdf/vsphere4/r41/vsp_41_esx_server_config.pdf for more information on how to configure your virtual network on your ESX Server.
Direct Access Mode 1. Dedicate a spare NIC port on your ESX Server. 2. Create a virtual switch for the dedicated NIC port. Then, create a network label for this switch. 3. Map this network label to the sample network on the SonicWALL WXA 5000 Virtual Appliance. 4. Connect an ethernet cable between the spare NIC port of the ESX Server and a dedicated interface on
SonicWALL NSA/TZ security appliance.
10
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
VLAN Trunks Mode 1. Assign a VLAN ID to a virtual switch on the ESX Server. 2. Give it a network label for the virtual switch. 3. Map this network label to the sample network on the SonicWALL WXA 5000 Virtual Appliance. 4. Allocate an unused interface on SonicWALL NSA/TZ. 5. Connect an ethernet cable between the unused interface on SonicWALL NSA/TZ and to a port on the
physical switch connected to your ESX Server. 6. Configure access mode for the VLAN ID on the port of the physical switch where the SonicWALL NSA/TZ
is connected.
To isolate and segment virtual machine traffic, refer to : http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004074
11
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
NSA/TZ Trunking Mode 1. Assign a VLAN ID to a virtual switch on the ESX Server. 2. Give it a network label for the virtual switch. 3. Map this network label to the sample network on the SonicWALL WXA 5000 Virtual Appliance. 4. Enable trunking on the physical switch port attached to the LAN interface of the SonicWALL NSA/TZ
security appliance. 5. Configure a VLAN interface on top of the LAN interface.
12
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
Installing the WXA 5000 using VMware vSphere This section details the installation of the SonicWALL WXA 5000 Virtual Appliance using the VMware vSphere. Perform the following steps to complete the WXA 5000 installation:
1. Download the SonicWALL WXA 5000 Open Virtual Appliance (OVA). 2. Login to your vSphere client. 3. Click File, then select Deploy OVF Template.
The “Deploy OVF Template” pop-up window displays:
4. Specify the location of WXA 5000 OVA file by clicking the Browse button. 5. Select the SonicWALL WXA 5000 OVA file. Then, click the Next button.
13
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
The SonicWALL WXA 5000 “OVF Template Details” display:
6. Verify the product name is “wxa5000-1.1.0-0-x”, then click the Next button.
The “Name and Location” options display:
7. Specify a Name and Location for deploying the SonicWALL WXA 5000, then click the Next button.
14
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
The “Host / Cluster” options display:
8. Choose a Host or Cluster for running the SonicWALL WXA 5000, then click the Next button.
The “Resource Pool” options display:
9. Select the Resource Pool, then click the Next button.
15
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
The “Disk Format” options display:
10. Select the Thick Provisioned Format (recommended), then click the Next button.
The “Network Mapping” options display:
11. Select the network you created in the “Choosing a Network Deployment Mode” section, then click the Next
button.
16
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
The “Ready to Compete” screen displays:
12. Verify the configuration before deploying the SonicWALL WXA 5000, then click the Finish button.
Please wait while your SonicWALL WXA 5000 is being deployed, this may take several minutes.
The “Deployment Completed Successfully” pop-up window displays when the WXA 5000 deployment is complete:
17
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
13. Navigate to the chosen Host/Cluster for SonicWALL WXA 5000 and click Power on the virtual machine.
14. Right click on the VM and select Open Console.
18
SonicWALL WXA 5000 Getting Started Guide P/N 232–002101–00 Rev A
Getting Started Guide
After the SonicWALL WXA 5000 finishes booting up, the following screen displays:
15. Select Show Network Settings, then press the Enter key.
The DHCP IP address assigned by the SonicWALL NSA/TZ displays:
The SonicWALL WXA 5000 Virtual Appliance is now operational. Navigate to the WAN Acceleration tab on your SonicWALL NSA/TZ to further configure the WAN Acceleration service.
_____________________ Last updated: 2/29/2012
