THE NEW STANDARD IN BIOMEDICAL 3D PRINTING

ANTIBACTERIAL NANOCOMPOSITEPLACTIVE

DISCOVER

Produced by a ISO 9001/2015 companyManufacturer Compliance

FROM THE DEEPEST COPPER MINES IN CHILE

We are a Chilean companyfounded by professionalspassionate about the impact thatnew technologies have on thequality of life of people.Copper3Duses the bestNano-Copper additive in theworld, functionalized andimproved toprovide the bestantibacterial action against awide range ofmicroorganisms.

To the most sofisticated and high endantibacterial products of the world

Produced by a ISO 9001/2015 companyManufacturer Compliance

PLACTIVE AN1™ is an innovative Nanocomposite developed with ahigh quality PLA and a patented, scientifically validated and highlyeffective Nano-Copperadditive.This unique combinationof technologiesbrings the followingcharacteristics to ourproducts:

This graphic shows the results of 2studies conducted by microbiologylaboratoriesin USA and Chile1,2.Both studies confirm that the ColonyFormingUnits (CFU) ofStaphylococcusaureusMRSA andEscherichia coliDH5α, falls abruptly during the first 6 hoursof exposure to PLACTIVE (>95%),continuing the elimination of bacterialstrains until reaching >98% eliminationat 8 hours and >99.99% elimination at24hours.

1.SITU Biosciences MicrobiologyLaboratory,USA.2.MicrobiologyLaboratory of Universidad Católica de Valparaíso, Chile.

PLACTIVE ™ ANTIBACTERIAL ACTIVITY

We believe in the power of innovation to reshape the future.

Antibacterial action has been scientifically validated eliminatingmore than99.99% of fungi,viruses, bacteria and a wide rangeofmicroorganisms.

Clinically tested in prosthesis for amputees with excellentresults. Ideal for the manufacture of other medical applicationswhere itʼs dangerous to have bacterial contamination, such aspostoperative prostheses, wound dressing and surgicalequipment.

Antibacterial properties confirmed by two microbiologylaboratoriesin Chile andUSA.PLACTIVE™ is a FDA RegisteredMaterial and EU compliant(No. 10/2011,No.1935/2004and No. 2023/2006).The manufacturer also has certification ISO 9001/2015and isREACH compliant.

The Nano-Additivemantains all the mechanical properties ofthematerial

It has thermoforming characteristics that facilitatespost-processing and final adjustments of the 3D printedapplication.

Non-toxic product and environmentally friendly (biodegradable).

3DPRINTER CONFIGURATION PARAMETERS WITH PLACTIVE™

™MATERIAL PROPERTIES OF PLACTIVE ™

BE A PART OF THIS NEW ECOSYSTEM AND JOIN

THE ANTIBACTERIAL 3D PRINTING REVOLUTION!

PRINTING TEMP. 190 -210 °CPRINTING SPEED 40 -50 MM/SEGLAYER HEIGHT ≥ 0.1 MMPRINT BED TEMP. ± 0 -60 °C

Physical PropertiesSpecific Gravity, g/ccMFR, g/10 min(2)

Relative Viscosity(3)

ClarityPeak MeltTemperature, °CGlass Transition Temperature, °CMechanical PropertyTensileYield Strength, psi (MPa)Tensile Strength at Break, psi (MPa)Tensile Modulus, psi (MPa)Tensile Elongation, %Notched Izod Impact, ft-lb/in (J/m)Flexural Strength, psi (MPa)Flexural Modulus, psi (MPa)Heat Distortion Temperature, °C66 psi (0.45 MPa)

PLACTIVE TM

1.2464.0Transparent145-16055-60

8700 (60)7700 (53)524,000 (3.6)60.3 (16)12,000 (83)555,000 (3.8)

55

ASIM MethodD792D1238D5225-D3418D3418

D882D882D882D882D256D790D790

E2092

“Keep the package sealed until ready touse andpromptly reseal anyunused material”(1)Typical properties for injection molded amorphousbars;nottobe construedas specifications.(2) 210 °C/2. 16kg(3) RV measured at1.0 g/dLin chicro format30°C*values can vary by +/-5%due to environmental conditions