96
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 1/96 Dishwasher Training  2011 New Door Configuration 2011 E - Star

2011 E Star GE Dishwasher Training - 2011 New Door Configuration

Embed Size (px)

Citation preview

Page 1: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 1/96

Dishwasher Training – 2011

New Door Configuration2011 E - Star

Page 2: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 2/96

2

Updates Front Control Models

• 2011 E-star w/ enhanced control.

• Locking connectors on control/harnesses.

• Upper rack slides improved to wheels on rails.

• Revised tines spacing in upper/lower racks.

New Product  Top Controls on Plastic Tubs

• Top controls – new console and tactile UI for control.

• Locking connectors on harnesses.

• Pocket handle and towel bar handle models.

• Racking improvements – upper rack slides + tine spacing improvements.

• Gray tubs and inner doors .

New Product  Entry level Top Controls on SS Tubs

• Top controls – new console and tactile UI (same as above)

• Limited pocket handle models.

Current front control

New pocket handle top control

Page 3: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 3/96

3 7/28/2011

IMPORTANT SAFETY NOTICE

The information in this presentation is intended for use by individualspossessing adequate backgrounds of electrical, electronic, & mechanicalexperience. Any attempt to repair a major appliance may result in

personal injury & property damage. The manufacturer or seller cannot beresponsible for the interpretation of this information, nor can it assumeany liability in connection with its use.

WARNING

To avoid personal injury, disconnect power before servicing this product.

If electrical power is required for diagnosis or test purposes, disconnectthe power immediately after performing the necessary checks.

RECONNECT ALL GROUNDING DEVICES

If grounding wires, screws, straps, clips, nuts, or washers used to

completea path to ground are removed for service, they must be returned to theiroriginal position & properly fastened.

Page 4: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 4/96

4 7/28/2011

GE Factory Service Employees are required to use safety glasses with side

shields, safety gloves steel toe shoes for all repairs.  

Dyneema® CutResistant Glove 

Steel Toe Shoes Plano Safety Glasses 

VR Gloves – provide shock protection 

Prescription Safety Glasses 

Safety Glasses

must be

compliant with

ANSI Z87.1-2003 

Page 5: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 5/96

5 7/28/2011

Front Control

Top Control

Page 6: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 6/96

7/28/2011

New Door componentsTactile Control Buttons, Vent, Pocket Door Handle and

Front Light Indicator Lens

Page 7: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 7/96

Page 8: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 8/96

7/28/2011

Cycles and Times (Top Control):

Auto**: 5-7 gallons* 49-133 minutes*

Sanitize: 8.8-11.8 gallons* 50-279 minutes*

Normal: 3.3-8.3 gallons* 54-143 minutes*

Light: 7.6-10.5 gallons* 46-88 Minutes*

*Min = low soil

Max = high soil and all options selected

35 minute heated dry in Normal Wash

45 minute dry in Auto, Sanitize and Light Wash

Steam Option adds 15 minutes to cycle

**Some models do not have an Auto Cycle

Use and Care shows Minimum Times. No Enhancements

Page 9: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 9/96

7/28/2011

Cycles and Times (Front Control):

Pots Pans or Heavy**:

11.8 gallons 88 minutes (Timed cycle)

Sanitize**:  8.8-11.8 gallons* 50-279 minutes*

Normal:  3.3-8.3 gallons* 54-143 minutes*

Light**:

7.6-10.5 gallons* 46-88 Minutes*

China Crystal**:

9.2 gallons 41 minutes (Timed Cycle)

Rinsed Only**: 1.2 gallons 7 minutes

*Min = low soil

Max = high soil and all options selected

35 minute heated dry in Normal Wash

45 minute dry in Auto, Sanitize and Light Wash

Steam Option adds 15 minutes to cycle

**Some models do not have an this Cycle

Use and Care shows Minimum Times. No Enhancements

Page 10: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 10/96

10 7/28/2011

Cycle Time Definition Normal or Auto Cycles with allHeat Options selected (times and cycles change

depending on Turbidity Sensor readings)Pre- Pre- Pre- Steam Steam Pre- Pre- Main Post Post FinalWash Wash Wash Wash Wash Wash Wash Wash Rinse

Water Valve (seconds) 63 17 17 63 21 63 21 21 63 23 23Circulation (minutes) 5 5 5 15 2 10 15 30 2 3 10Heater (minutes) 17 7 10 15 30 8 5Drain (seconds 7 7 75 10 75 10 10 75 11 11 105

35 minute heated dry in Normal Wash45 minute dry in Auto,

Note: depending on Turbidity Response, it is possible the cycle could skipfrom the first Pre-Wash to the Main Wash and then to Final Rinse.

Page 11: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 11/96

11 7/28/2011

Mini Manual Location - Plastic Tub

Page 12: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 12/96

12 7/28/2011

Passive Vent, No Fan or damper

Page 13: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 13/96

13 7/28/2011

Indicator Lamp Lens

Solid Amber when running, Solid Green when Clean

Page 14: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 14/96

14 7/28/2011

Improved Racks, Rollers and Tracks, Plastic tub

Page 15: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 15/96

15 7/28/2011

New rollers on Rack

New end caps, notice new tab

Page 16: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 16/96

16 7/28/2011

Push Tabto centerto remove

Page 17: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 17/96

17 7/28/2011

Page 18: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 18/96

187/28/2011

Track, Rear Cap and Roller / Stud on tub

Page 19: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 19/96

197/28/2011

Door Strike / Catch is non adjustable

Page 20: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 20/96

207/28/2011

Tub TCO location

1 shot with Manual reset Trip at 189 with manual reset

Page 21: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 21/96

217/28/2011

Tub TCO is resettable, if tripped, Reset TCO &replace the control

Page 22: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 22/96

227/28/2011

Fill hose should be inserted 1 1/2 inches

Page 23: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 23/96

23 

7/28/2011

Fill Funnel, inside tub

Page 24: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 24/96

24 

7/28/2011

Rotate Clockwise to remove

Page 25: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 25/96

25 

7/28/2011

Fill funnel seal

seal

Page 26: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 26/96

26 

7/28/2011

Turn Counterclockwise and lift to remove wash arm

Page 27: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 27/96

27 

7/28/2011

Coarse Filter

Fine Filter

Hub Nut

Page 28: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 28/96

28 

7/28/2011

Remove nut to remove Fine Filter

Page 29: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 29/96

29 

7/28/2011

Lift Fine Filter to remove

Page 30: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 30/96

30 

7/28/2011

To remove Top Wash Arm and Conduit, remove¼” Hex screw 

Conduit

Page 31: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 31/96

31 

7/28/2011

Lift Tab, continue to remove Conduit

Page 32: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 32/96

32 

7/28/2011

Push Conduit back and to side to finish removal,being careful to not break tab.

Page 33: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 33/96

33 

7/28/2011

To remove Sump Cover push in 4 tabs and lift cover

Page 34: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 34/96

34 

7/28/2011

To Remove sump filter, the tabs can be released with ascrewdriver or putty knife

Page 35: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 35/96

35 

7/28/2011

Push Sump Filter to right and lift to remove

Page 36: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 36/96

36 

7/28/2011

Tab location for cover and filter removal

Cover tabs

Sump Tabs

Page 37: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 37/96

37 

7/28/2011

To remove the wash arm hub or support, twistcounterclockwise. It will make a snap noise when the locator

tab on the tub breaks (this is normal).

Page 38: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 38/96

38 

7/28/2011

With hub removed, Coarse Filter can now be removed

Page 39: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 39/96

39 

7/28/2011

Coarse Filter removal.

Page 40: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 40/96

40 

7/28/2011

Proper location of the Wash Arm Bearing or ThrustWasher

Page 41: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 41/96

41 

7/28/2011

Make sure the Bearing or Thrust Washer is in placewhen re-assembled.

Page 42: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 42/96

42 

7/28/2011

Overfill System will only cut voltage to Water Valve.To remove cover, unscrew ¼” Screw and lift Cover 

Page 43: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 43/96

43 

7/28/2011

Float Dome, to remove, simply lift

Page 44: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 44/96

44 

7/28/2011

Float Stem activates Flood Switch below.

I d l2 screws at bottom of door

Page 45: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 45/96

45 

7/28/2011

Inner door removal

2 machine screws located at hinge

6 screws top part of inner door

New Door Components

Page 46: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 46/96

46 

7/28/2011

New Door Components;

Inner DoorOuter Door

Tactile SwitchesVentingLocking Connectors

Passive Vent

Page 47: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 47/96

47 

7/28/2011

New Top Control Inner Door configuration

Console

Vent TactileSwitch

Vinyl Shield

Cover

Door Switch Assembly

Page 48: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 48/96

48 

7/28/2011

Vinyl Shield will only have to be removed if console isreplaced, it can be folded up to access control.

Vinyl Shield MUST be in place.

Page 49: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 49/96

49 

7/28/2011

Shield folded back to show control TCO, locatedon cover

1 shot Trip at 280

Page 50: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 50/96

50 

7/28/2011

Control TCO is one shot, If tripped, look for control,connector wire damage. Replace damaged components.

Page 51: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 51/96

51 

7/28/2011

Cover removal, 1. lift top and pull out, 2. pushbottom down

1.

2.

Page 52: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 52/96

52 

7/28/2011

To remove control board, remove 1 screw in center ofboard and release tabs. Notice locking connectors.

Tabs Screw

Page 53: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 53/96

53 

7/28/2011

Model Select MUST be Transferred or newcontrol will not operate, just flash

Page 54: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 54/96

54 

7/28/2011

Insulator between control board and console,Must be installed

Page 55: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 55/96

55 

7/28/2011

Pocket Handle has 4 screws, control board mustbe removed to access screw under control.

Page 56: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 56/96

56 

7/28/2011

Handle can now be removed from the front

Page 57: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 57/96

57 

7/28/2011

Tactile switch has 2 screws securing switch toconsole

Page 58: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 58/96

58 

7/28/2011

Switch has a silicone pad to protect frommoisture and buttons. Wire harness must be

removed from control board.

Page 59: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 59/96

59 

7/28/2011

Buttons and Silicone Pad come as an assembly

Page 60: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 60/96

60 

7/28/2011

Notice buttons are keyed, they fit one way

Indicator light on front panel Solid Amber when unit is

Page 61: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 61/96

61

7/28/2011

Indicator light on front panel. Solid Amber when unit isoperating, Solid Green when cycle ended and dishes

are clean

To Remove Door Switch assembly

Page 62: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 62/96

62

7/28/2011

To Remove Door Switch assembly,unscrew 2 screws, Insulator MUST be used

Door Switch Assembly held in place with bracket and 2

Page 63: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 63/96

63

7/28/2011

Door Switch Assembly held in place with bracket and 2screws. Insulator must be in place (previous slide)

Door Switch comes as an assembly 2 switches and

Page 64: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 64/96

64

7/28/2011

Door Switch comes as an assembly, 2 switches andbracket / actuator

Page 65: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 65/96

65

7/28/2011

When replacing Front Panel, Console or Light Lens, theVent will have to be removed and replaced

(double back tape cannot be reused)New vent will come with Console and Lens as a Kit

vent

Page 66: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 66/96

Page 67: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 67/96

67

7/28/2011

Remove any excess adhesive from the outer door

Disposeold vent

Page 68: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 68/96

68

7/28/2011

Install new vent on clean panel

Page 69: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 69/96

Page 70: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 70/96

70

7/28/2011

Console removed

Lens

Page 71: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 71/96

717/28/2011

Lens

Adhered with doubleback tape

Console must be removedto access lens

WASHABILITY COMPLAINTS1 Level DW left to right and front to back

Page 72: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 72/96

727/28/2011

1. Level DW left to right and front to back.

2. Verify presence of air gap or high drain loop.

3. Confirm lower spray arm thrust washer is installed

4. Confirm spray arms spin freely.

5. Confirm spray arm jets are clear.

6. Confirm no breaches, tears or clogs in fine filter under the bottom spray arm. Clean if necessary.

7. Confirm coarse filter clean and seated with no gaps (not warped).

8. Remove cover inlet and sump filter.

9. Remove any debris from sump.

10. Reinstall sump filter and cover.

11. Confirm Calrod is operating properly. If not, check connections and TCO. If TCO is open,

suspect control problem.12. Close detergent cup and use Service Mode to verify the lid opens.

13. Inlet water temperature should be at least 120 degrees F.

14. Turn on dishwasher and fill; check for correct water level

15. Test water hardness with WD01X10295 or WX5X370 test strip. Adjust detergent use

accordingly. Refer to Owner's Manual.

16. Use a highly rated detergent: generally detergent tablets or packs work best. Refer to Owner's

Manual.17. Use a rinse agent.

18. Load dishwasher per Owner's Manual.19. Select cycles and options according to the soil level. Refer to Owner's Manual. 

Page 73: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 73/96

737/28/2011

Correct water levelMain wash is suggested time to check for proper level.

Page 74: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 74/96

747/28/2011

Page 75: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 75/96

757/28/2011

Schematic

Page 76: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 76/96

767/28/2011

Schematic

Control replacement / Calibration

Page 77: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 77/96

777/28/2011

The dishwasher will enter into the TEST/

CALIBRATION mode at first power-up.

The door must be closed and latched.

WAIT until the second fill (approximately6 minutes from power-up) to cancel cycle

by pressing the Start/Reset pad.

The dishwasher will be ready to operate

after the pump out. 

Page 78: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 78/96

787/28/2011

SS units have different Racking andInner Door Vent

Tactile Switch Assembly and Vent on outer

door is the same as on Plastic Tub

Page 79: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 79/96

79 7/28/2011

Mini Manual Location - Stainless Tub

Tub TCO is located Front Center behind cross member

Page 80: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 80/96

807/28/2011

Tub TCO is located Front Center behind cross member.If it is open, replace the control.

TCO

Trips at 165, auto reset at 150 

SS Upper rack - slide

Page 81: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 81/96

817/28/2011

Upper rack extended outward Front view with rack pushed in.

NOTE: Removing front end caps

will not release rack

Upper rack - slide

Page 82: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 82/96

827/28/2011

To remove upper rack assembly, press “down” to disengage lever on left side

and “up” on the right side.

(Right side)

Pull rack assembly forward and out 

Page 83: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 83/96

837/28/2011

Door catch is non-adjustable

Page 84: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 84/96

847/28/2011

Door separated, there are no hangers to balance thedoor as on previous models.

Inner door componentsC ff

Page 85: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 85/96

857/28/2011

Vent, Control cover and door switch different,compared to plastic tub

Page 86: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 86/96

867/28/2011

Console Component ViewTo remove Console, Handle and Vent must be

removed

Handle ScrewsVent

Door Switch

TCO

Control and cover

Tactile Switch

1 shot Trip at 280

Page 87: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 87/96

877/28/2011

Single door switch, breaks line side

Vent on SS units is different than Plastic Tubs

Page 88: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 88/96

887/28/2011

Vent on SS units is different than Plastic Tubs.Correct install is critical for proper operation.

It is possible to install the vent incorrectly!

Page 89: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 89/96

897/28/2011

The vent is keyed, but in the middle.The vent can be installed incorrectly.

SS Vent correctly installed

Page 90: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 90/96

907/28/2011

Correct positioning

Incorrect position, no airflow = no dry / poor dry and leaks out bottom of door

Page 91: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 91/96

917/28/2011

Incorrect position 

WASHABILITY COMPLAINTS1. Level DW left to right and front to back.

Page 92: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 92/96

927/28/2011

2. Verify presence of air gap or high drain loop.

3. Confirm lower spray arm thrust washer is installed

4. Confirm spray arms spin freely.

5. Confirm spray arm jets are clear.

6. Confirm no breaches, tears or clogs in fine filter under the bottom spray arm. Clean if necessary.7. Confirm coarse filter clean and seated with no gaps

8. Remove cover inlet and sump filter.

9. Remove any debris from sump.

10. Reinstall sump filter and cover.

11. Confirm Calrod is operating properly. If not, check connections and TCO. If TCO is open,

suspect control problem.12. Close detergent cup and use Service Mode to verify the lid opens.

13. Inlet water temperature should be at least 120 degrees F.

14. Turn on dishwasher and fill; check for correct water level

15. Test water hardness with WD01X10295 or WX5X370 test strip. Adjust detergent use

accordingly. Refer to Owner's Manual.

16. Use a highly rated detergent: generally detergent tablets or packs work best. Refer to Owner's

Manual.17. Use a rinse agent.

18. Load dishwasher per Owner's Manual.19. Select cycles and options according to the soil level. Refer to Owner's Manual. 

Correct water levelMain wash is suggested time to check for proper level.

Page 93: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 93/96

937/28/2011

gg p p1st fill is 63 seconds, there is a partial drain and fill before

main wash.

Service Mode SS

Page 94: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 94/96

94 7/28/2011

Page 95: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 95/96

Page 96: 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration

http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 96/96