˝ˆ˛ˇ BVE-9100 - BroadcastStore.com · ˝ˆ˛˙ BVE-9100 • Product Guide Contents • i Contents Introduction 1 About This Guide

BVE-9100Product Guide

C U T D I S S W I P E

BVE-9100 • Product Guide

Part Number BC-00583

Revision A, October 1996

Printed in U.S.A.

Copyright

© 1996 Sony Corporation. All rights reserved.

Neither this guide nor the software described herein, in whole or in part, may bereproduced, translated or reduced to any machine readable form without prior writtenapproval from Sony Corporation.

• Sony is a registered trademark of Sony Corporation.

• Betacam, Betacart, Jumbotron, and Umatic are registered trademarks ofSony Corporation.

• Dynamic Tracking (DT) and Library Management System are trademarksof Sony Corporation.

• GVG is a registered trademark of The Grass Valley Group Inc.

• Kadenza is a trademark of The Grass Valley Group Inc.

• Vista is a trademark of Ampex Corporation.

Notice to Users

SONY CORPORATION PROVIDES NO WARRANTY WITH REGARD TO THISGUIDE, THE SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN,AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OFMERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITHREGARD TO THIS GUIDE, THE SOFTWARE OR SUCH OTHER INFORMATION.IN NO EVENT SHALL SONY CORPORATION BE LIABLE FOR ANYINCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, WHETHER BASEDON TORT, CONTRACT, OR OTHERWISE, ARISING OUT OF OR INCONNECTION WITH THIS GUIDE, THE SOFTWARE OR OTHERINFORMATION CONTAINED HEREIN OR THE USE THEREOF.

Sony Corporation reserves the right to make any modification to this guide or theinformation contained herein at any time without notice.

The software described herein may also be governed by the terms of a separate enduse license agreement.

All features, functions, and specifications are subject to change without notice.

BVE-9100 • Product Guide Contents •• i

Contents

Introduction 1

About This Guide........................................................................................................................ 1

Features and Benefits 3

BVE-9100 Feature Overview ..................................................................................................... 3The One Disk Solution.................................................................................................. 4

Basic Tools................................................................................................................................. 4Distributed Processing.................................................................................................. 4System Flexibility......................................................................................................... 5Menu Flexibility........................................................................................................... 5System Interfaces.......................................................................................................... 5System Software........................................................................................................... 6List Management........................................................................................................... 6EDL Capacity and Multiple Bins.................................................................................. 6Audio Control............................................................................................................... 7Keyboard Convenience................................................................................................. 7GPI Ports ...................................................................................................................... 7Color Display............................................................................................................... 8

Power Tools ............................................................................................................................... 9Status Reporting............................................................................................................ 9Programmable Control Panel........................................................................................ 9EDL Capability........................................................................................................... 10Keyboard and Menu Flexibility.................................................................................. 10Time Track................................................................................................................. 10Record and Source Assignment .................................................................................. 11Switcher Memory and Learn....................................................................................... 11Dynamic Motion Memory........................................................................................... 12Sync Jog...................................................................................................................... 12Pre-Read..................................................................................................................... 12Archiving and Caching ............................................................................................... 13

Caching ........................................................................................................ 13Archiving ..................................................................................................... 14

Configuration Guide 15

BVE-9100 Configuration .......................................................................................................... 15Basics ....................................................................................................................................... 16

Editing Control Unit Electronics (NTSC)................................................................... 16Advanced Operating Program..................................................................................... 16Hard Disk Unit............................................................................................................ 16

ii •• Contents BVE-9100 • Product Guide

Keyboards and Panels ............................................................................................................... 17Editing Keyboard (Qwerty) ........................................................................................ 17Editing Keyboard (Dedicated).................................................................................... 17Programmable Control Panel ...................................................................................... 17Sub Keyboard ............................................................................................................. 17

Monitors.................................................................................................................................... 18Edit Status Monitor ..................................................................................................... 18Monitor Cable............................................................................................................. 18

Switcher Interfaces.................................................................................................................... 18Switcher/Mixer/Monitor Switcher Interface Card...................................................... 18Switcher Control Program (Sony)............................................................................... 18Switcher Control Program (GVG/Sony) ..................................................................... 19Switcher Control Program (GVG 200) ....................................................................... 19Switcher Control Program (GVG Kadenza)................................................................ 19Switcher Control Program (Abekas)........................................................................... 19Switcher Control Program (AVC Vista) ..................................................................... 19

Audio Mixer Interfaces ............................................................................................................. 20Mixer Control Program............................................................................................... 20

Interface Cards and Cables ....................................................................................................... 20Multi Interface Card (4 Port) ...................................................................................... 20Ethernet I/O Card........................................................................................................ 20System Cables............................................................................................................. 20

GPI Expansion........................................................................................................................... 21IDC (Intelligent Device Controller)............................................................................ 21IDC chassis................................................................................................................. 21GPI Board................................................................................................................... 21

Order Guide — BVE-9100 ....................................................................................................... 22Instructions.................................................................................................................. 22

Request Form............................................................................................................................ 23Expansion Kit............................................................................................................................ 24

BVE-9000 Expansion Kit ........................................................................................... 24

Installation Guide 25

BVE-9100 Installation............................................................................................................... 25BVE-9100 Keyboard................................................................................................................. 26BVE-9100 Chassis — Front View............................................................................................ 27

Rack Mounting............................................................................................................ 27BVE-9100 Chassis — Rear View............................................................................................. 28BVE-9100 Chassis — Specifications ....................................................................................... 29BVE-9100 Connectors .............................................................................................................. 30

RS-422 Connector Specifications............................................................................... 30BKE-9011 15-Pin Connector Specifications .............................................................. 30Printer Connector Specifications ................................................................................ 32Color VDU Out Chassis Connector Specifications..................................................... 32CTG-11V (31V) Cable Connector Specifications ...................................................... 33GPI Connector Specifications — Chassis................................................................... 34GPI Connector Specifications — BKE-9651.............................................................. 34

BVE-9100 System Interconnection Chart — Typical ................................................................ 37BVE-9100 Customer System Interconnection Chart .................................................................. 38

BVE-9100 • Product Guide Contents •• iii

Appendix A. Feature List 39

BVE-9100 — Feature By Feature............................................................................................. 39System Setup............................................................................................................... 40Signal Source Selection.............................................................................................. 40Edit Mode................................................................................................................... 41Transition Type .......................................................................................................... 41Data Entry................................................................................................................... 42Preview and Replay ................................................................................................... 43List Management......................................................................................................... 44Learn Modes............................................................................................................... 46Recording Features..................................................................................................... 47Disk Management ....................................................................................................... 48

Appendix B. Related Resources 49

Related Resources .................................................................................................................... 49Printed Media............................................................................................................. 49Audio/Video Media.................................................................................................... 50

Appendix C. Sales and S ervice 51

General Information and Reference........................................................................................... 51Regional Sales Offices.............................................................................................................. 52Regional Service Centers.......................................................................................................... 53National Parts Centers .............................................................................................................. 54Emergency Response System.................................................................................................... 55SUPPORTNETSM .......................................................................................................................... 56SOFTWAREPLUSSM ................................................................................................................... 56

Glossary 57

Index 61

iv •• Contents BVE-9100 • Product Guide

BVE-9100 • Product Guide Introduction •• 1

Introduction

About This Guide

CUT DISS WIPE

As the flagship editing system for Sony, the BVE-9100 continues the tradition set bythe BVE-9000. The professionals that use editing systems are constantly demandingnew features, tools and interfaces to keep up with today’s requirements for creativityand speed. The BVE-9100 delivers, with creative interface capabilities, a full rangeof options, outstanding peripheral device control, and superb day-to-day operatingfunctions.

To assist you with assembling the optimum system for your customer’s needs, thisguide is divided into the following chapters:

• Chapter 1 — Features and Benefits

This chapter provides a detailed description of the BVE-9100’s features— not just lists of numbers and modes, but concise explanations of“why” certain features are so valued.

• Chapter 2 — Configuration Guide

This chapter provides itemized descriptions of BVE-9100 features andoptions to assist with configuration planning. To simplify the orderingprocess, a convenient quotation request form is also included.

• Chapter 3 — Installation Guide

This chapter offers information and diagrams to assist with facilityengineering and equipment integration requirements.

2 •• Introduction BVE-9100 • Product Guide

• Appendix A — Feature List

This appendix provides a category-by-category description of BVE-9100 features and operating modes.

• Appendix B — Related Resources

This appendix lists additional written and visual reference materialavailable for further reading and research on the BVE-9100.

• Appendix C — Sales and Service

This appendix provides basic information about Sony sales, service,emergency response, and software support.

• Glossary

The glossary provides a reference list of important editing and videoterms used throughout this guide.

A comprehensive “Index” is also provided for your reference.

BVE-9100 • Product Guide Features and Benefits •• 3

Features and Benefits

BVE-9100 Feature Overview

CUT DISS WIPE

IN01:00:10:0022:12:00:00

STILLS T O P

OUT01:00:20:00

This chapter provides a comprehensive discussion of BVE-9100 features, taking abroad-brush approach to both the functionality and the benefits of the system’s basicand “power” tools. Concise explanations relating to the importance of each feature inthe edit suite are provided.

The following sections are included in this chapter:

• The “One Disk Solution” section discusses the one all-encompassingprinciple under which the BVE-9100 is designed.

• The “Basic Tools” section outlines important large categories of BVE-9100 features used in day-to-day editing.

• The “Power Tools” section outlines the large feature categories thateditors value the most on the BVE-9100.

For a finely focused approach to each feature, refer to Appendix A, “Feature List.”This appendix provides detailed tables and descriptions of BVE-9100 features —arranged according to functionality.

Note that some features described in the following sections may apply only when Sonyperipheral equipment is used.

4 •• Features and Benefits BVE-9100 • Product Guide

The One Disk SolutionAs you review the topics in this chapter, keep in mind that the BVE-9100 has beendesigned with one all-encompassing principle — to be the editor’s one disk solutionin post production — to provide an EDL (Edit Decision List) that stores virtuallyeverything that transpires during the edit session.

This requirement is paramount because editors change things, and clients (by theirnature) request changes. The more complete the EDL — the easier the changes, andthe easier to recreate the edit session at a later date.

When editing systems were first designed in the early 70’s, editors got pretty excitedthat timecode numbers (alone) were stored in the EDL! But as editing systemsevolved — as productions themselves became more complex — the EDL itself had toprogress beyond the original interchange standard. The EDL simply wasn’t smartenough to remember all the editor’s moves.

Gradually, more and more fields of information were added to the EDL. Theseincluded more detailed transition information, notes, GPIs and memory triggers, aswell as VTR (Video Tape Recorder) transport speeds. But still — not enough ...

Now, with the BVE-9100, the one disk solution is at hand. The BVE-9100’s EDL hasevolved to a sophisticated storehouse of data — one that not only retains the basics,but also adds switcher “learn” files, color correction data, TBC (Time BaseCorrector) data, audio mixer levels, dynamic motion memory data (including “learn”files), recorder “swap” information, and the systems advanced “Status Reporting” —on an edit-by-edit basis.

When you record an edit on the BVE-9100, the entire data set for all devices used inthe event is stored in the EDL. Using simple “pointers” for precise repeatability, alldata is referenced to the source reel names stored on disk. When you recall an edit,everything comes back. Go ahead — tell the client to change away! Anything shortof re-shooting the scene is OK with the BVE-9100.

As you read forward, keep the “one disk solution” in mind. It is perhaps the primaryreason that the BVE-9100 is so popular among editors.

Basic ToolsThis section describes basic BVE-9100 features used in day-to-day editing. Thesefeatures are found in most high-end editing systems, but the BVE-9100 has manyvalue-added entries in this first category.

Distributed ProcessingThe BVE-9100 is controlled by a series of 32-bit microprocessors. Using a techniquecalled distributed processing, the master CPU handles all high level editing functions,while dedicated CPUs on the interface boards handle the communications with allperipheral devices.

Speed is everything in post — editors are impatient enough without having to wait forthe editing system to process its data and buffer the edit. Because the system isoptimized for speed in essential areas such as list management, the BVE-9100 waitsfor the editor to make his or her decisions — not the other way around.


System FlexibilityThe BVE-9100 is a modular, cost-effective system with a wide range of options.Systems can be tailor-made to suit the individual needs of the facility, with the built-incapacity for expansion as the facility itself grows. A customer can start with thebasics and add device controllers and other peripherals as required.

Today’s facilities can not afford a system that’s inflexible — our industry’s hardwarecontinues to evolve and shows no signs of slowing down. The editing system must beas flexible and adept as the clients that come in to use it. With the BVE-9100,continuing opportunities for system expansion are built-in.

Menu FlexibilityThe BVE-9100 is a multi-menu system. A variety of convenient and easy-to-usemenus provide access to all the necessary editing, system, and setup functions:

• The Edit Data Page lays out the current edit in a convenient data-plus-graphic format, and provides a “window” into the EDL. The entiredisplay (both color and layout) can be customized.

• The Setup Menu accesses setup functions for devices, crosspointassignments and I/O communications.

• The Initialization Menu assigns devices, sets EDL specifications, anddetermines overall “preferences” such as preroll and color framing.

Setup and Initialization menus are required in a high-end editing system — there’s noway around it. The BVE-9100’s menus are logical and well-designed, with extensivesetup control. Best of all, you can design short-cuts to frequently used functions —avoiding a few keystrokes along the way.

System InterfacesAn extensive range of Sony VTRs, ATRs (Audio Tape Recorders), Switchers, Mixers,DVEs (Digital Video Effects) and Color Correctors can be controlled directly viaserial communications:

• For Sony VTRs (in addition to the standard transport commands),features such as DT and TBC levels are directly controllable.

• For Sony DVS/BVS series switchers, multi-M/E access as well E-File(memory register) control is standard. In addition, keyframe, timelineand effect control for the DVS-6000, 7000, and 8000 work directly fromthe BVE-9100’s jog/shuttle dial.

• For the Sony DMX-E3000 audio mixer, crosspoint, transition, preview,and “snapshot” functions are fully supported.

• For DME (Digital Multi Effects) units such as the DME-3000 and DME-7000, keyframe, timeline and effect control is easy — directly from theBVE-9100’s jog/shuttle dial.

The BVE-9100 system also works with selected devices from other manufacturerssuch as Ampex, Abekas, GVG® and Graham-Patten. And, using the optional BKE-9402 Programmable Control Panel, peripheral control is centralized in one compactunit — like having a tape operator (and an assistant director) at your fingertips.


The more devices you can control accurately in a session, the more accurate the EDLitself. With Sony peripheral devices under serial control, the BVE-9100’ssophisticated interfaces contribute yet another link in Sony’s one disk solution.

System SoftwareAll BVE-9100 system software runs from the internal hard drive. Software upgradesand optional switcher/mixer interfaces are provided on floppy disk for convenienceand ease of installation. In addition to the internal hard drive, two 3.5" disk drives arestandard for storing (or archiving) EDLs and set-up files. Because the system’s UI(user interface) and operating environment can be customized by an editor, the BVE-9100 allows you to store files on-board — or out-board.

Out-board storage simply means that (with the EDL disk in hand), an editor canassemble a program across town or across the nation — at another BVE-9100 facility— with precisely the same configuration that was used in the original suite. And withyour custom set-up disk, there’s no time wasted in UI setup — ever.

List ManagementWith the advanced operating program, full list management capabilities including bothstandard and advanced functions (such as trace and cleanup) are at your fingertips.List management is simply a set of software tools for manipulating EDL timecodenumbers and events. The numbers represent scenes in a program, and carefuladjustment is often required to solve a problem, move a scene around, or enhance aparticular transition.

Just like any toolbox, some list management tools are used more often than others —when one is needed, it’s a lifesaver — if it’s missing, precious time can be lost. Withthe BVE-9100, the list management toolbox is full.

EDL Capacity and Multiple BinsThe BVE-9100’s standard EDL memory capacity is 6000 lines, with expansioncapability available. More importantly, up to sixteen EDLs (also called “bins”) canbe handled in memory simultaneously — almost twice the number that was previouslyavailable.

An editor is an organized individual. His or her ability to organize the vast amount ofdata required for a production is vital to the show’s success — and the efficiency ofthe session. Sixteen EDL “bins” simply means increased organization and increasedefficiency.

Imagine a closet with 16 shelves (rather than one) — it’s easier to separate the pantsfrom the shirts! In an editing system with 16 bins, it’s far easier to stay organized thanit is with one large “catch-all” bin. You can store multiple versions of a program,individual audio-only lists and individual effects-only lists, or even reserve listsexclusively for switcher E-Files — in other words, keep things organized!


Audio ControlWhen using digital VTRs such as the DVR-1000/2100, DVR-10/18/20/28, and DVW-series, the BVE-9100 provides full four-channel audio control. Individual channelscan be enabled in any combination, and independent split inpoints can be set asneeded.

This high degree of control simply means that you can record narration on channel 1,audio effects (or a second language track) on channel 2, and a stereo music bed onchannels 3 and 4 — and worry about the 2-channel mixdown later — not during theinitial editing!

Keyboard ConvenienceThree different types of keyboards are available for the BVE-9100, to suit the preciseneeds of the facility’s editors:

• The Qwerty keyboard provides all functions in a standard typewriter-style array. This layout is familiar to most editors, and is known as the“industry standard” keyboard.

• The “dedicated” keyboard arranges similar functions in convenientgroups of buttons. As well as providing instant familiarity to BVE-910and BVE-2000 operators, this keyboard offers a comfortable transitionfor editors familiar with similar keyboards on older Ampex, Paltex, andConvergence editing systems.

• An available “sub” keyboard (BKE-9401) provides four levels of 30assignable buttons (120 assignments total), and offers the ability to placeany system function in a more convenient desktop location. An importantfunction that’s located several keystrokes away on a setup menu can bebrought to the top level for simplicity. The sub keyboard works withboth the dedicated and Qwerty keyboards.

A choice of keyboards simply means that editors don’t have to relearn their current(and comfortable) style of editing. They can start from an instant level of tactilefamiliarity — and progress from there.

GPI PortsFour GPI (General Purpose Interface) output ports are standard, and expandable to amaximum 36 output ports. The software for triggering the ports includes a variety ofconvenient operating modes.

GPIs are required for both old and new peripheral devices that do not have the benefitof a serial communications port. Even though most contemporary devices have serialcontrol ports, many older cart machines, still store, character generators and ATRs fallinto this category. Using a simple contact-closure approach, GPI ports allow you totrigger these devices with frame-accuracy.


Color DisplayThe BVE-9100’s color display is easy to read and can be customized for editorconvenience and comfort. Just as editors like to change their shows around, they alsolike to be able to customize their editing environment — choosing just the right colorsand the right layout of editing information. Convenient menus allow you to customizethe display, and store the resulting setups on disk — as you like it!


Power ToolsThis section outlines the features that editors value the most on the BVE-9100. Powertools simplify the editor’s job, increase the editing session’s efficiency, and separatethe BVE-9100 from the competition.

Status ReportingThe BVE-9100 uses “Status Reporting” to interface with peripheral devices. Statusreporting is essentially a system of advanced two-way communications that allows thepanel status of outboard devices to be reported to — and stored in — the BVE-9100’sEDL in real-time. Once in the EDL, the data can be modified quickly and easily (afterall — editors change things!)

Status reporting takes full advantage of the many capabilities of Sony switchers,VTRs, color correctors, mixers, and many more devices. For example,

• If a complex event is easier (and faster) to set up at the switcher — do itthat way! Status reporting passes the data to the BVE-9100.

• If the color corrector’s control panel happens to be in the machine room,you can adjust the source VTR’s color from the BVE-9100 — as if thecolor corrector was in front of you — the results are identical.

Status reporting boils down to this — convenience. Whether the editor is a keyboardperson or a “hands-on-device” person — status reporting makes it transparent. Youractions and adjustments are stored in the EDL, regardless.

Programmable Control PanelIt’s clear that editors love to tweak things in an editing session, but they hate to crossthe room to do it! To that end, the BKE-9402 Programmable Control Panel centralizesmultiple control panels into one. The unit itself plugs into the BVE-9100 keyboard,and allows the editor to talk directly to all devices capable of status reporting.Whether it’s mixers, DVEs, transports, color correctors or switchers, at the touch of abutton the BKE-9402 becomes the control panel for the remote device — allowingadjustment and memorization of the device’s settings in the EDL.

Any device that plugs into a BKE-9011 or BKE-9014 can be controlled from theBKE-9402. Because communications is bi-directional, not only can the editor controlexternal devices, but if an adjustment is made locally (for example, by a tape operatorin the machine room), the BKE-9402 reports the adjustment instantly.

The BKE-9402’s display can also be customized, placing the most needed featureswithin easy reach. Because everything needs to be tweaked during a session at onetime or another, the BKE-9402 and makes adjustment a pleasure.


EDL CapabilityWith the tremendous amount of data required during an edit session, the overallcapability of the BVE-9100’s 16 EDL bins help keep a show organized and movingefficiently — and keep the editor organized. Here are just a few of the high points:

• Repeatability — when an edit is performed, whether simple orcomplex, all pertinent data is stored in the EDL. When you recall theedit, everything comes back — for precise repeatability.

• Security — the entire EDL “structure” is protected by battery backup —in case of power failure, all is restored.

• Bin Setup — in the special “SSU” (System Setup) mode, each bin canbe associated with its own unique parameters such as differentrecorders, source machines, and different screen colors and layouts.When you change bins, the entire system setup changes accordingly.

• Bin Management — a wide range of software tools help the editor tomanage the bins during post. The 16 bins can be named, cleared, movedand copied, and you can cut and paste events between bins.

Refer to the section “The One Disk Solution” for more details on data storage and thereasoning behind the BVE-9100’s unique EDL structure.

Keyboard and Menu FlexibilityThe BVE-9100 literally allows an editor to create the precise system (or operatingenvironment) needed for a given edit session.

• The Key Assignments Menu allows editors to customize the actualkeyboard layout and all associated functions. You can move, swap,copy, or remove keys — and save the data in a file for use at any time. Ifyou don’t like where the Play button is — move it!

• The Layout Menu allows editors to re-configure the position and colorinformation on the edit screen. If you’re comfortable with the Sonylayout, no need to adjust. But if you grew up using a CMX or GVG,system, rearrange the menu — and get comfortable! There’s nodifference with way the BVE-9100 edits.

Time TrackSome editing systems call it match-frame, Sony calls it “Time Track” — regardless ofthe name, it’s one of the most powerful modes on the BVE-9100 system. Simply put,Time Track finds matching video frames that in turn enable you to synchronizemachines and perform clean, seamless transitions.

When an edit is originally performed, a sync relationship between source and recorddecks is established. If the client wants to change that scene (now or in the future),that relationship must be re-established — precisely. No jump-cuts allowed! Withoutthe Time Track capability, paper and pencil (and endless scrolling of the EDL)wouldn’t begin to spell the trouble you’d have finding the right match.

Some editing systems have two or three match-frame modes. Sony has eightindividual Time Track modes that not only match the sources, but also each of theperipheral devices used in an edit.


You can match sources to recorders, recorders to sources, match memory triggers andmatch action within the event. You can even match dynamic motion control events thatinclude speed ramps (a feat quite difficult to accomplish on other editing systems).

Refer to the “Data Entry” table in the “Feature List” section for an itemizeddescription of each Time Track feature.

Record and Source AssignmentA maximum of 14 VTRs can be rolled simultaneously in an edit. Of that 14, you canutilize as many as 12 source devices or as many as eight recorders. Source devices(or machines) can be any combination of serial controlled VTRs, DMEs, DDRs(Digital Disk Recorders), and switchers. All play and record assignment is a simplekeyboard operation.

The BVE-9100 also has a powerful “temp” (temporary) record function, in which anydevice can be assigned as a recorder with the Temp Record button. Onceaccomplished, all preview switching and monitoring is automatically re-routed —with no need to patch.

Whether the record assignments are permanent or temporary, the current recorder isclearly listed in the menus, and all record assignments are stored in the EDL. As youjog thru the list, recorders change dynamically. Best of all, if you auto-assemble thelist, the system swaps recorders as necessary on an edit-by-edit basis.

Switcher Memory and LearnMost high-end editing systems have one or more methods for triggering switchereffects. In addition to standard “cut - wipe - dissolve” functionality, the BVE-9100uses a method called Switcher Memory to trigger the switcher, and a feature calledSwitcher Learn to memorize switcher effects.. Here are just a few capabilities:

• You can trigger up to 255 individual switcher events — in just one EDLevent.

• You can create switcher effects from the editing keyboard, directly fromthe switcher, or a combination of the two — to suit your style.

• Just like a snapshot, all switcher clips, gains, crosspoints and durationsare stored in the EDL in the switcher event timeline.

• You can memorize a series of “live” events with Switcher Learn (justlike learning a dynamic motion memory event for a VTR) and play itback on the switcher with precision.

• You can create switcher events without having to worry about losingdata — “Status Reporting” makes it possible.

The BVE-9100’s switcher memory and learn features both underline Sony’s systemintegration concept, and focus clearly on simplicity. Editors can set up effects at theirown comfort level, with the knowledge that EDL storage is transparent.

And if (by some mysterious chance) the client accidentally presses “Black” on allswitcher banks — and tweaks each and every clip, you can simply press “Backspace”on the BVE-9100 to recall the switcher event intact.


Dynamic Motion MemorySlow motion control is one of those “must have” features. It can be a pleasure to use,or it can become a nightmare on less capable editing systems. The BVE-9100’s DMCMotion Memory function is well thought-out — and an editing pleasure:

• Just like Switcher Learn, you can trigger up to 255 individual VTRmotion events — in just one EDL event.

• You can learn DMC events with the jog/shuttle dial, or program themstep-by-step (one speed change at a time) from the editing keyboard.

• You can edit an event’s timeline, with the ability to program stepped(instantaneous) speed changes, ramped (gradual) speed changes andfreeze-frames.

• You can match precisely into a DMC event with Time Track.

You’ll never know how important accurate and repeatable DMC events are — untilyou’re asked to run a scene in reverse, ramp the speed, and match-frame out!

Sync JogSome editing systems call it sync-roll, others call it master/slave mode, Sony calls it“Sync Jog” — regardless of the name, it’s a method for locking two or more sourcedevices together. The BVE-9100’s sync jog mode, however, goes the extra mile byincluding the ability to lock non-transport devices (such as switchers and DVEs)together. For example:

• On the easy side, sync jog allows you to track and jog two sourcemachines, one with a traveling matte (key), and one with the fill video.

• In a multi-camera “ISO” situation, sync jog allows you to track allsource VTRs used in the original shoot, whether the timecode issynchronous or offset.

• On the more complex side, if you want to track two VTRs, each runningat a variable play speed (including reverse), and follow action acrossscreen with a switcher wipe and a DVE move, sync jog allows you to“keyframe” the event for perfect tracking — of all devices.

Simple sync jog edits are extremely convenient, with full EDL listing. Complex editsthat might have required frame-by-frame animation can be handled easily with syncjog, with far greater flexibility and ease.

Pre-ReadPre-Read is the ability for a digital VTR to read digital information (both audio andvideo) off tape — prior to writing the data back on tape. Also known as “read beforewrite,” this feature is all-important in post-production — for speeding up editingsessions, for avoiding B-rolls, and for solving problems.

With the BVE-9100, pre-read is easy and comprehensive, as follows:

• In the “auto” mode, pre-read is enabled whenever the edit’s contextrequires it. For example, if the system detects that you’ve programmed adissolve from R to A, pre-read is enabled.


• All pre-read edits are remembered in the EDL as such, and recalled thatway during re-edit and auto-assemble situations.

• For safety when auto-clean is enabled, overlaps are not cleaned if pre-read is on.

• Unlike many other editing systems, all preview and record passes arehandled in an identical manner when pre-read is enabled. The clientwill not be saying “what was that glitch” with the BVE-9100’s mode.

The BVE-9100’s pre-read capabilities add convenience and flexibility, with aminimum of keystrokes for the operator.

Archiving and CachingThe BVE-9100 enables you to use record-capable devices (other than the masterrecorder) as “Caching” and “Archiving” devices.

Caching

In brief, “caching” represents a group of BVE-9100 features that record scenes (orportions of scenes) to other devices in order to accelerate the editing process. Fourprimary caching modes are available:

• Tail Cache

Also called Auto "B" Roll, the Tail Cache mode sets aside a VTR (orDDR) for automatic B-roll recording. Pre-read is superb, but not alledit suites have the luxury (or budget) for digital switchers and digitalVTRs. In this situation, when the need arises for an instant B-roll, theTail Caching mode eliminates the hassle of laying off clips.

When preview is pressed and the BVE-9100 detects the need for a B-roll(for example, a dissolve from A to A), the “to” source is automaticallydubbed to the B-roll recorder — and then rolled as the “B” playbacksource. Full EDL listing is provided for re-recording and auto-assemblypurposes. Note also that if the record machine is selected as a source,the system makes an automatic “A” roll.

• Head Cache

The Head Cache mode (also used with Random Access Preview),functions when two DDRs are connected. In this mode, the system pre-loads an EDL with same reel dissolves. Using multi-preview, thesystem then attempts to preview the entire EDL without stopping disks.

• Auto Cache

The Auto Cache mode is similar to Tail Cache, except that Auto Cachemode caches every “closed-end” edit that is performed — on the fly —regardless of the transition type.


• Super Quick Preview/Record

The Super Quick Preview/Record mode is a subset of the Head Cachemode. When enabled, the system performs a continuous preview of aseries of transitions, thus providing more time to try different versions ofan edit. Many editors find this mode extremely useful for quicklychecking continuity over a series of transition point.

The caching modes are supported when the BVE-9100 is interfaced with DDRs fromAbekas, Mountain Gate, Pronto, and Accom.

Archiving

Although it’s become a life saver, pre-read can also be dangerous as many editorshave discovered. With a simple keystroke, 2 hours of precise layering can be turnedinto toast. To prevent this from happening, the BVE-9100 includes an “archive”feature that designates a VTR as an archive recorder.

Each time the primary recorder goes into edit mode, so does the archive recorder.The difference, though, is that the archive recorder always adds clips sequentially —and never goes back and over-records. The result is a perfect record of all scenes thatcomprise the master, providing full protection and security. With archiving, you canalways fix a toasted layer!

BVE-9100 • Product Guide Configuration Guide •• 15

Configuration Guide

BVE-9100 Configuration

CUT DISS WIPE

This chapter provides itemized descriptions of BVE-9100 features and options. Inaddition, to assist with pre-sales planning and to simplify the BVE-9100 orderingprocess, a convenient quotation request form is also included.

The following sections are included:

• Basics

• Keyboards, Panels and Cables

• Monitors

• Switcher Interfaces

• Audio Mixer Interfaces

• Interface Cards

• GPI Expansion

• Order Guide

• Request Form

• Expansion Kit

16 •• Configuration Guide BVE-9100 • Product Guide

BasicsThis section describes the basic components that comprise a BVE-9100 system.

BVE-9100 Editing Control Unit Electronics (NTSC)The BVE-9100 electronics chassis houses the main system electronics, hard drive,floppy drives, communication ports, monitoring ports, and reference connectors. FourGPI output ports are standard. In its maximum configuration, the chassis providesports for up to 28 serial controlled devices.

Multiple slots are provided for interface cards, including the BKE-9011Switcher/Mixer/Monitor Switcher Interface card, the BKE-9014 Multi InterfaceCard, and the BKE-9002 IDC (Intelligent Device Controller) card for GPIexpansion. Refer to the sections on each individual card for further details.

In the “Installation Guide” chapter, refer to the “BVE-9100 Chassis” section for achassis diagram and list of chassis specifications.

BZE-9102 Advanced Operating ProgramThe BZE-9102 Advanced Operating Program provides all the necessary softwarefeatures required for editing with the BVE-9100. The package includes both basicand advanced editing modes, such as advanced DDR control, list management andmultiple EDL bin control.

Please note that the previous version of the operating system, BZE-9101, is no longeravailable.

BKE-9107 Hard Disk UnitThe BKE-9107 Hard Disk Unit provides 40 megabytes of internal storage capacity forEDLs, setup files, and configuration files.


Keyboards and PanelsThis section describes the keyboards, secondary control panels, and cables that can beadded to a BVE-9100 system.

BKE-9400A Editing Keyboard (Qwerty)The Qwerty Keyboard presents all functions in a standard typewriter-style array.This layout is known as the “industry standard.”

In the “Installation Guide” chapter, refer to the “BVE-9100 Keyboard” section for akeyboard diagram and list of keyboard specifications.

Note: for cable runs from the chassis to the keyboard exceeding 30 meters,please contact your Regional Product Specialist.

BKE-9410 Editing Keyboard (Dedicated)The “dedicated” keyboard arranges similar editing functions in convenient and logicalgroups of buttons. The keyboard provides instant familiarity to BVE-910 operators,and a comfortable transition for users of older Ampex, Paltex, and Convergenceediting systems.

Note: for cable runs from the chassis to the keyboard exceeding 30 meters,please contact your Regional Product Specialist.

BKE-9402 Programmable Control PanelThe BKE-9402 Programmable Control Panel centralizes multiple control panels intoone. The unit plugs into the BVE-9100 keyboard and allows bi-directionalcommunications with any device that connects to a BKE-9011 or BKE-9014interface card. Peripheral devices such as mixers, DVEs, transports, color correctorsand switchers can be adjusted, and their settings can be stored in the EDL.

The BKE-9402 “kit” includes a power supply, connector box, and a cable forinterconnection with the main chassis.

BKE-9401 Sub KeyboardThe “sub” keyboard is a programmable unit that provides four levels of 30 assignablebuttons (120 assignments total), with the ability to place any system function in a moreconvenient desktop location. The sub keyboard works with both the Dedicated andQwerty keyboards, and includes a cable for keyboard interconnection.


MonitorsThis section describes the monitors that can be added to a BVE-9100 system.

Edit Status MonitorA variety of SVGA status display monitors are available from Sony, such as themodel CPD-15SF2. Due to the continuing improvement in monitor technology andthe wide range of choices available for specific applications, refer to your Sonycatalog or contact your Sony sales office for details on the current models available.

CTG- Monitor Cable

11V, 31V The CTG-series cables connect the BVE-9100 chassis to the selected RGB statusmonitor. Two lengths are available:

• CTG-11V, 10 meters• CTG-31V, 30 meters

Switcher InterfacesThis section describes the switcher interface hardware and software that can be addedto a BVE-9100 system.

BKE-9011 Switcher/Mixer/Monitor Switcher Interface CardThe BKE-9011 Switcher/Mixer/Monitor Switcher interface card provides RS-422ports for communications to a variety of video switchers and audio mixers. Modelsfrom most broadcast manufacturers are supported. The card also interfaces with theexternal Sony DVS-1201, BVS-1201, or GVG-10x switcher for preview switchingcapability.

Note: one card maximum can be installed in the BVE-9100 system.

BZE-9604 Switcher Control Program (Sony)The BZE-9604 Switcher Control Program provides a set of software drivers for theSony DVS (digital) and Sony BVS (analog) series switchers.


BZE-9601 Switcher Control Program (GVG/Sony)The BZE-9601 Switcher Control Program provides software for controlling thefollowing switchers:

• GVG Model 100, 300, 1000, 1200, and 1680• Sony HDS-1000T

Software is provided on floppy disk, and the option includes an installation andoperation manual.

BZE-9602 Switcher Control Program (GVG 200)The BZE-9602 Switcher Control Program provides software for controlling the GVGModel 200, 2200, 3000, and 4000 series switchers. Software is provided on floppydisk, and the option includes an installation and operation manual. Note that thisprogram also controls the Abekas model A8150.

BZE-9603 Switcher Control Program (GVG Kadenza)The BZE-9603 Switcher Control Program provides software for controlling the GVGKadenza™ switcher. Software is provided on floppy disk, and the option includes aninstallation and operation manual.

BZE-9605 Switcher Control Program (Abekas)The BZE-9605 Switcher Control Program provides software for controlling thefollowing switchers:

• Abekas A82, A83, A84• Abekas A8100, A8150

Software is provided on floppy disk, and the option includes an installation andoperation manual.

BZE-9606 Switcher Control Program (AVC Vista)The BZE-9606 Switcher Control Program provides software for controlling theAmpex AVC Vista™ series switcher. Software is provided on floppy disk, and theoption includes an installation and operation manual.


Audio Mixer InterfacesThis section describes the audio mixer software interfaces that can be added to aBVE-9100 system.

BZE-9611 Mixer Control ProgramThe BZE-9611 Mixer Control Program provides a set of software drivers for theSony DMX-E3000 or MXP-S390 series mixers. Graham-Patten (GPS) ESAM IIprotocol can be selected to support audio mixers from other manufacturers.

Interface Cards and CablesThis section describes the interface cards that can be added to a BVE-9100 system.

BKE-9014 Multi Interface Card (4 Port)The BKE-9014 Multi Interface Card controls four RS-422 devices per card. Devicesinclude VTRs, ATRs, DDRs, DMEs, and CCRs. Up to six cards can be installed inthe BVE-9100 system. (Note that only five BKE-9014 cards can be installed if boththe BKE-9002 and BKE-9011 cards are installed.)

The four ports must be configured in groups of two similar devices. For example:

• One card can control four VTRs.• One card can control two VTRs and two DMEs.• One card can not control one VTR, one CCR, and two DMEs.

BKE-9102 Ethernet I/O CardThe Ethernet I/O Card provides an Ethernet AUI interface. This functionality allowsyou to network several BVE-9100 editing systems together, or marry a host computerto the BVE-9100 as a file server. This configuration supports the transfers of EDLsand setup data.

RCC- System Cables

5G, 10G, 30G The RCC-series cables provide RS-422 extensions for serial controlled devices.Three lengths are available:

• RCC-5G, 5 meters• RCC-10G, 10 meters• RCC-30G, 30 meters

RCC cables are required to connect the chassis to RS-422 devices. Note that somedevices include RS-422 cables as standard.


GPI ExpansionGPI expansion allows you to add 16 or 32 additional GPI ports to the BVE-9100system. Each GPI port is controlled via software. Three components workingtogether are required:

• 1 (one) BKE-9002 IDC (Intelligent Device Controller)

• 1 (one) BKE-9600 IDC chassis

• Up to 2 (two) BKE-9651 GPI boards

This section describes each component.

BKE-9002 IDC (Intelligent Device Controller)

The BKE-9002 IDC (Intelligent Device Controller) card is required for GPIexpansion. A maximum of one BKE-9002 can install in the main BVE-9100 chassis.The card itself provides the interconnection between main electronics and the externalBKE-9600 IDC chassis.

BKE-9600 IDC chassis

The BKE-9600 IDC chassis is required for GPI expansion. A maximum of oneBKE-9600 can connect to the BKE-9002. The BKE-9600 itself is an external 1RUchassis that provides slots for up to 2 (two) BKE-9651 GPI boards.

BKE-9651 GPI Board

A maximum of two (2) BKE-9651 GPI boards install in the BKE-9600 IDC chassis.Each board provides 16 individual GPI output ports. With two boards installed, 32additional GPI output ports are provided.

In the “Installation Guide” chapter, refer to the “GPI Connector Specifications”section for a list of GPI pinouts.


Order Guide — BVE-9100

Fax CoverTo:

Fax #:

From:

Date:

Pages:

Message:

Customer InformationCompany Name:

Address:

Phone:

Fax:

Contact:

Title:

InstructionsThe Request Form on the following page includes a table of all BVE-9100 basic and optional components. Usethe table to configure the customer’s optimum BVE-9100 system.

Please perform the following steps:

• As a prerequisite, review the information in the “Installation Guide” chapter, and work with thecustomer to complete “BVE-9100 Customer System Interconnection Chart.” This chart determinesthe number of interface cards required.

• Complete the customer information section above.

• In the table, check off the basic and optional items required. Note that recommended items are markedwith an X in the “Rec” column.

• Mark quantities (where appropriate), exceptions, and comments in the “Notes ” column.

• Use the completed form to create a detailed BVE-9100 proposal.

• For submitting the completed proposal, the area at the top of this page can be used as a convenient faxcover sheet.


Request Form

BVE-9100 System Components

Part # Description Rec √√ Notes

Basics

BVE-9100 Editing Control Unit (NTSC) X

BZE-9102 Advanced Operating Program X

BKE-9107 Hard Disk Unit X

Keyboards and Panels

BKE-9400A Editing Keyboard (Qwerty) X

BKE-9410 Editing Keyboard (Dedicated)

BKE-9402 Programmable Control Panel X (opt)

BKE-9401 Sub Keyboard

Monitors

SVGA Monitor X Refer to the “Edit Status Monitor” section inthis guide for instructions

CTG-11VCTG-31V

10 meter Monitor cable30 meter Monitor cable

X Select one

Switcher Interfaces

BKE-9011 Switcher/Mixer/Mon. Switcher Interface Card X Maximum one per system

BZE-9604 Switcher Control Program (Sony) X

BZE-9601 Switcher Control Program (GVG/Sony)

BZE-9602 Switcher Control Program (GVG 200)

BZE-9603 Switcher Control Program (GVG Kadenza)

BZE-9605 Switcher Control Program (Abekas)

BZE-9606 Switcher Control Program (Ampex AVC Vista)

Audio Mixer Interfaces

BZE-9611 Mixer Control Program (Sony/Graham-Patten) X

Interface Cards and Cables

BKE-9014 Multi Interface Card — 4 ports (VTR/ATR/DDR/DME/CCR) X (2) 6 maximum (5 if both the BKE-9002 andBKE-9011 are installed)

BKE-9102 Ethernet I/O Card

RCC-5GRCC-10GRCC-30G

5 meter RS-422 cable10 meters RS-422 cable30 meters RS-422 cable

X Select one per RS-422 control deviceinterface

GPI Expansion

BKE-9002 IDC (Intelligent Device Controller) card One required for expansion

BKE-9600 IDC chassis One required for expansion

BKE-9651 GPI board (16 GPI ports) Maximum 2 boards


Expansion KitThis section describes the expansion kit that is used to convert a BVE-9000 to a BVE-9100.

BKE-9000K1 BVE-9000 Expansion Kit

The BKE-9000K1 Expansion Kit provides the necessary hardware and software forconverting a BVE-9000 to a BVE-9100.

Because each BVE-9000 system includes a different array of boards and options,each upgrade is essentially a “custom” procedure. A variety of important individualBVE-9000 upgrades are required to ensure that all BVE-9100 features functionproperly.

As a prerequisite for upgrading, the customer should be prepared to provide the salesrepresentative with the following “checklist” items:

Provide BVE-9000 serial number.

Provide current BVE-9000 system configuration, including a list of allperipheral equipment connected to the editor.

Provide current version of video switcher software in use, for example,BZE-9601 through BZE-9606. This software must be upgraded.

Provide current version of audio mixer software in use, for example,BZE-9611. This software must be upgraded.

Provide current version of editing software.

Provide current versions of the VTR control boards in use, for example,BKE-9004A and BKE-9012. These boards must be upgraded.

Please note the following important points:

• Individual upgrades must be ordered through Sony National PartsCenters.

• As part of expansion, the BKE-9107 Hard Disk Unit is highlyrecommended for convenience and speed.

• If the customer’s current software and hardware configurations are notavailable, the customer or sales representative can contact SonySOFTWAREPLUS

SM for details on the customer’s configuration.

• For further assistance with system expansion and upgrading, pleasecontact your regional Product Specialist.

BVE-9100 • Product Guide Installation Guide •• 25

Installation Guide

BVE-9100 Installation

CUT DISS WIPE

This chapter provides information and diagrams to assist with facility engineering andequipment integration requirements. The following sections are included:

• The “BVE-9100 Keyboard” section provides a detailed keyboarddiagram and a table of keyboard specifications (dimensions, power,environmental and connectors).

• The “BVE-9100 Chassis” section provides a detailed chassis diagramand a table of chassis specifications (dimensions, power, environmentaland connectors). Connector “pinout” tables are also provided.

• The “BVE-9100 System Interconnection Chart — Typical” sectionprovides a detailed diagram of a typical BVE-9100 editing system.

• The “BVE-9100 Customer System Interconnection Chart” sectionprovides a comprehensive diagram that can be completed by the salesrepresentative.

This diagram allows you to configure the required components of anediting system, to suit the customer’s specific requirements and assist inthe preparation of a detailed proposal. Instructions are provided in thesection.

26 •• Installation Guide BVE-9100 • Product Guide

BVE-9100 KeyboardThe figure below illustrates the BVE-9100 keyboard.

TRACE

Q-TRC

MXRLOCALSWR

PF1

F 1PF2

F 2PF3

F 3PF4

F 4PF5

F 5PF6

F 6PF7

F 7PF8

F 8

TEST

MAINT

LOADSSU

SAVE

SETUPMULTIEDL

RENUMCACHEMNGR

SORT

SCROL

CLEAN

GAP

MXMEMDEL

EVENT

SWMEMMOD

EVENT

DMMEMCREATEEVENT

AUTOCACHETEMP-R

DMCRANGESY-GR

OUT

SCRPD

BLOCK

EDIT# MA/SL

XPTASSIGNREEL

R P1 P2 P3 P4 P5 P6 AUX1 AUX2 BLACK A1 A2 A3 A4

SHTL JOG DMC

PF5

PF1

PF6

PF2

PF7

PF3

PF8

PF4

NOBACK

SCROLCLEAR

CLR1

ARITH

=

LASTX

/7 8 9

4 5 6

1 2 3

*

+

0 00 F/TC -

INITLOADEDL

SAVEEDL

MODEDL

CRCTEDIT INSRT DEL MOVE NOTE LAST

EDITRECAL

RCL-SCR

+

-

SAVE

BS

XCHG

FS RET

MULTI-PVWPREVIEW

MPPVW

P-PVW

SWPVW

R-PVW

AUTORECOFF REPLAY

SYNCPLAYGOTO

AUXGPI

ASMBV

A3A1

A4A2 CUT DISS WIPE

ENTER

CTRL R P1 P2 P3 P4 P5 P6SPEED

SPLIT

BACKINSET

BACKOUTSET

BACKDURSET

PTNKY

KEY

MAN-R

MAN

SHIFTPLAY-REW

PLAY+FF

STOPSTIL

SCANPLAY SLOW

RECRDTRACKAUTO

SPLITMARK

IN

SPLITMARKOUT

U-BITMARK

CONST

STORECONSTRECAL DISK SHIFT

OUTGOTO IN

ALLSTOP

BVE-9100 Keyboard

The following table lists keyboard specifications:

BVE-9100 Keyboard Specifications

Parameter Specification

Dimensions mm: 620 (w) x 65 (h) x 260 (d)inches: 24.5 (w) x 2.625 (h) x 10.25 (d)

Weight (approximate.) 5.2 kg11 lb. 7 oz.

Remote Out 15-pin D-sub connectorEquivalent to RS-422A standardDC power input level: 12 to 15V

Aux In 15-pin D-sub connectorInput level: CMOS level (VIH 4 V, VIL 1 V)

Aux DC In XLR 4-pin connectorInput level: 12 to 15V

Operating temperature +5° to +35°C+41° to +95°F

Storage temperature -20° to +60°C-4° to +140°F

Power requirement DC 12 to 15V

Power consumption Max. 500 mA (at 12 V input)Normal 300 mA (at 12 V input)Rush current 10 A (at 12 V input, shorter than 10 ms)


BVE-9100 Chassis — Front ViewThe figure below illustrates a front view of the BVE-9100 chassis.

POWER

ON

OFF

RUN

1

2

A B

E D I T I N G C O N T R O L U N I T B V E - 9 1 0 0

1 2 3

4

BVE-9100 Chassis — Front View

Front chassis components are listed below:

1. Power Indicator

2. Power Switch

3. Run 1, 2 indicators

4. Floppy disk drives

Rack M ountingThe BVE-9100 can be rack-mounted in a standard 19" rack. When rack-mounted, usethe supplied rack angle and screws. It is also recommended that you use the followingrack mount equipment:

• ACCURIDE Rack Mount Slides Model 305, slide length 22 inch

• ACCURIDE bracket # 5516-2


BVE-9100 Chassis — Rear ViewThe figure below illustrates a rear view of the BVE-9100 chassis.

1

R E F V I D E O

F I E L D R E F

M A I NK Y B D G P I

P R I N T E RC O L O R V D U

B / W V D U

A U X

A C I N

2 3 4 5 6 7 8 9 10 11 12 13 14

15

E T H E R N E T

BVE-9100 Chassis — Rear View

Rear chassis components are listed below:

1. Slots for RS-422 device interface cards (BKE-9002, BKE-9011,BKE-9014).

2. Reference video input/output connectors (BNC)

3. Field reference input connector (BNC)

4. Main keyboard connector (D-sub 15-pin)

5. GPI connector (D-sub 15-pin)

6. Black and white VDU (video display unit) connector (BNC)

7. Printer connector (D-sub 25-pin), RS-232C interface

8. Color VDU (video display unit) connector (D-sub 9-pin)

9. Slot for BKE-9102 Ethernet AUI option

10. Not used

11. Aux connector (D-sub 25-pin) for ISR.

12. Parallel FDU (floppy disk unit) connector (36-pin)

13. Ground terminal

14. AC In receptacle

15. Chassis cooling fan


BVE-9100 Chassis — SpecificationsThe following table lists chassis specifications:

BVE-9100 Chassis Specifications

Parameter Specification

Dimensions mm: 424 (w) x 220 (h) x 480 (d)inches: 16.75 (w) x 8.75 (h) x 19.00 (d)

Weight 21 kg (excluding optional boards)46 lb. 5 oz.

Reference video in BNC, Composite video or composite sync75 ohms, terminated

Reference video out BNC, loop-through output

Main Keyboard 15-pin D-sub connector, female

Printer 25-pin D-sub connector, female, RS-232C standard

GPI 15-pin D-sub connector, female

Field Reference BNC

Parallel FDU 36-pin Amphenol

B/W VDU BNC, 75 ohms, terminated

Color VDU 25-pin D-sub connector, female

Operating temperature +5° to +35°C+41° to +95°F

Storage temperature -20° to +60°C-4° to +140°F

Power requirement U.S.A. / Canada, 120 V AC +/- 10%, 48 Hz to 64 Hz

Power consumption 60 W

The figure below illustrates external dimensions (in millimeters):

4 2 4

2 2 0S i d e V i e w F r o n t V i e w

T o p V i e w4 8 0

BVE-9100 External Dimensions


BVE-9100 ConnectorsThe following connectors are listed in this section:

• RS-422 Connector• BKE-9011 15-Pin Connector• Printer Connector• Color VDU 9-Pin Chassis Connector• CTG-11V or 31V 15-Pin Cable Connector• GPI Connector (standard)• GPI Connector (optional with the BKE-9600 chassis and up to two

BKE-9651 cards)

RS-422 Connector Specifications

The following table lists RS-422 connector specifications:

5 4 3 2 1

9 678

RS-422 Connector Specifications

Pin # Signal Function

1 Frame GND Connected to the ground of the board

2 Receive A Receive data A

3 Transmit B Transmit data B

4 Transmit Common Transmit signal ground

5 Spare

6 Receive Common Receive signal ground

7 Receive B Receive data B

8 Transmit A Transmit data A

9 Frame GND Connected to the ground of the board

BKE-9011 15-Pin C onnector Specifications

The BKE-9011 card includes two 15-pin D-sub female connectors for audio/videopreview switching capability. A simplified block diagram of the 15-pin connectionsonly is shown below. Connector specifications are listed on the following page.

B K E - 9 0 1 1M I X E R S W ' E R

M O N 1 M O N 2

V i d e oM o n i t o rS w i t c h e r

A u d i oM o n i t o rS w i t c h e r

A 1

A u d i oM o n i t o r

S w i t c h e rA 2


A 4


A 3

BKE-9011 Simplified Block Diagram


The following table lists BKE-9011 MON 1 connector specifications:

5 4 3 2 1

91 01 11 2

678

1 31 41 5

BKE-9011 MON 1 Connector Specifications


1 A2 Select 1 Out Audio 2 selection output 1

2 — —





7 — —

8 Video Select 1 Out Video selection output 1




12 GND Connected to GND on IF-263 board

13 Video Select 4 out Video selection output 4



The following table lists BKE-9011 MON 2 connector specifications:

5 4 3 2 1

91 01 11 2

678

1 31 41 5

BKE-9011 MON 2 Connector Specifications



2 — —





7 — —

8 Video Select 1 Out Video selection output 1




12 GND Connected to GND on IF-263 board






Printer Connector Specifications

The following table lists Printer connector specifications. Note that this connector isRS-232C, not parallel.

5 4 3 2 1

1 41 51 61 7

678

1 81 92 0

1 0 91 11 21 3

2 2 2 12 32 42 5

Printer Connector Specifications

Pin # Signal I/O Function

1 Frame GND — Frame ground

2 TX | Received data (Transmit data from theterminal device)

3 RX O Transmit data (Received by the terminaldevice)

4 RTS | When this signal is positive level, the BVE-9100 transmits data.

5 CTS O When the BVE-9100 is able to receivedata, the signal comes to the positive level.

6 DSR O Fixed at +12 V

7 Signal GND — Signal ground

20 DTR | Indicates that the terminal device is ready.

Color VDU Out Chassis Connector Specifications

The following table lists specifications for the Color VDU Out connector on theBVE-9100 chassis.

5 4 3 2 1

9 678

Color VDU Out Chassis Connector Specifications

Pin # Signal I/O Function

1 GND — Ground

2 GND — Ground

3 Red Out O R signal

4 Green Out O G signal

5 Blue Out O B signal

6 Spare — —

7 Spare — —

8 Composite Sync Out O Composite sync signal

9 Spare — —


CTG-11V (31V) Cable Connector SpecificationsThe table below lists specifications for the 15-pin connector on the CTG-11V orCTG-31V extension cable. The cable includes two different types of connectors asshown below:

9-Pin Male(to chassis)

15-Pin Female(to monitor)

• The 9-pin “D” connector attaches to the Color VDU Out Connector onthe BVE-9100 chassis.

• The 15-pin “D” connector attaches to the cable on the rear of an SVGAedit status monitor.

5 4 3 2 1

1 0 789 6

1 5 1 4 1 3 1 2 1 1

(Female)External View

CTG-11V (31V) Cable Connector Specifications – 15-Pin end only


1 R R output. 0.714 V p-p (± 10%)/75 Ω

2 G G output. 0.714 V p-p (± 10%)/75 Ω

3 B B output. 0.714 V p-p (± 10%)/75 Ω

4 GND Ground

5 NC No connection

6 GND

7 GND Ground

8 GND

9 NC No connection

10 GND Ground

11 GND No connection

12 NC H sync output (TTL level)

13 H sync V sync output (TTL level)

14 V sync No connection

15 NC


GPI Connector Specifications — Chassis

The following table lists connector specifications for the standard GPI connector onthe BVE-9100 chassis. Four (4) GPI outputs are provided.

5 4 3 2 1

91 01 11 2

678

1 31 41 5

GPI Connector Specifications — Chassis


1 Relay 1 GPI-1 relay output

2 Return 1 GPI-1 relay output







9 TTL 4 GPI-4 TTL output


11 GND 1 GPI-1 TTL ground





GPI Connector Specifications — BKE-9651

When the external BKE-9600 IDC chassis is connected for GPI expansion, up to 2(two) BKE-9651 GPI cards can be installed — each of which provides 16 GPI outputports. Each BKE-9651 GPI card is identical, and each includes two connectors thatcan be assigned as follows:

• With one BKE-9651 card installed:– Connector 1 provides GPI output ports 1 through 8.– Connector 2 provides GPI output ports 9 through 16.

• With two BKE-9651 cards installed, on the second card:– Connector 1 provides GPI output ports 17 through 24.– Connector 2 provides GPI output ports 25 through 32.

Specifications for each connector are listed on the following page. Please note:

• Use shielded cable only. Connect the shield to the connector plug case.

• TTL input and TTL output are negative logic. Relay output is closedwhen TTL output is active, open when non-active.


The following table lists specifications for the first connector on a BKE-9651 card.This card provides GPI output ports 1 through 8, or 17 through 24.

11 8

1 93 6T o p V i e w

GPI Connector Specifications — BKE-9651, Connector 1


1 NC No connection

2 GND Connected to GND on IFB-10 board

3 NC No connection


5 Relay Out 1A TTL output 1

6 Relay Out 1B

7 L; TTL Out 1 TTL output 1


9 Relay Out 2A Relay output 2

10 Relay Out 2B




14 Relay Out 3B




18 Relay Out 4B




22 Relay Out 5B




26 Relay Out 6B




30 Relay Out 7B




34 Relay Out 8B





The following table lists specifications for the second connector on a BKE-9651card. This card provides GPI output ports 9 through 16, or 25 through 32.

11 8

1 93 6T o p V i e w

GPI Connector Specifications — BKE-9651, Connector 2


1 NC No connection


3 NC No connection


5 Relay Out 9A TTL output 9

6 Relay Out 9B




10 Relay Out 10B




14 Relay Out 11B




18 Relay Out 12B




22 Relay Out 13B




26 Relay Out 14B




30 Relay Out 15B




34 Relay Out 16B





BVE-9100 System Interconnection Chart — TypicalThe diagram below illustrates a typical BVE-9100 system.

B V E - 9 1 0 0C h a s s i s

V ideo Sw i t cherD V S / B V S S e r i e s

BK

E-9

011

Prev iew Swi tcher

Aud io MixerV S P / D M X S e r i e s , M X P w i t h E S A M

A d v a n c e d O p e r a t i n g P r o g r a m

B Z E - 9 1 0 2

Hard D isk Un i t( i n t e r n a l )

B K E - 9 1 0 7

Pr in te r( c u s t o m e r s u p p l i e d )

B /W Mon i t o r( O p t i o n a l )

K e y b o a r dB K E - 9 4 0 0 A ( Q w e r t y ) o rB K E - 9 4 1 0 ( D e d i c a t e d )

S u b K e y b o a r dB K E - 9 4 0 1

P r o g r a m m a b l e Con t ro l Pane l

B K E - 9 4 0 2

S V G AMon i t o r Cab le

C T G - 1 1 V o r 3 1 V

Dig i ta l V ideo Ef fec tsD M E S e r i e s

D ig i ta l D isk Recorde r

D ig i ta l Co lo r Cor rec to rB V X S e r i e s

V T RB V H , B V W , D V R , D V W S e r i e s

B K E - 9 6 0 0 I D C C h a s s i s

B K E - 9 6 5 1 G P I B o a r d( u p t o 2 )

E t h e r n e t

F i l e Se rve r PC( c u s t o m e r s u p p l i e d )

BK

E-9

014

BK

E-9

014

BK

E-9

014

J u n c t i o n B o x

A C

S V G A M o n i t o r( O p t i o n a l )



BK

E-9

002

BK

E-9

102

Note: I n th i s d iag ram, Sony mode ls a re shown . O the r mode ls o f pe r i phe ra l e q u i p m e n t a r e a l s o s u p p o r t e d .


BVE-9100 Customer System Interconnection ChartTo configure a customer’s BVE-9100 system, use the blanks to fill in the devicemodels and the software drivers required, then check off the desired BVE-9100system options. Use the completed chart to assist with the “Request Form.”

Model :(1 )

( 2 )

( 3 )

( 4 )

Model :(1 )

( 2 )

( 3 )

( 4 )

Model :( 1 )

( 2 )

M o d e l :

D r i ve r :

M o d e l :

M o d e l :

D r i ve r :

Model :( 1 )

( 2 )

B V E - 9 1 0 0C h a s s i s

V ideo Sw i t cher

BK

E-9

011

Prev iew Swi tcher

A d v a n c e d O p e r a t i n g P r o g r a m

B Z E - 9 1 0 2

Hard D isk Un i t( i n t e r n a l )

B K E - 9 1 0 7

Pr in te r( c u s t o m e r s u p p l i e d )

B /W Mon i t o r( O p t i o n a l )

KeyboardB K E - 9 4 0 0 A ( Q w e r t y )B K E - 9 4 1 0 ( D e d i c a t e d )

S u b K e y b o a r dB K E - 9 4 0 1

P r o g r a m m a b l e Con t ro l Pane l

B K E - 9 4 0 2

S V G AMon i t o r Cab le

Dig i ta l V ideo Ef fec ts

D ig i ta l D isk Recorde r

D ig i ta l Co lo r Cor rec to r

V T R

B K E - 9 6 0 0 I D C C h a s s i s

E t h e r n e t

F i l e Se rve r PC( c u s t o m e r s u p p l i e d )

BK

E-9

014

BK

E-9

014

BK

E-9

014

J u n c t i o n B o x

A C

S V G A M o n i t o r

V T R V T R

BK

E-9

002

BK

E-9

102

Aud io MixerB

KE

-901

4

BK

E-9

014

Mode l :

C T G - 1 1 VC T G - 3 1 V

Model :( 1 )

( 2 )

M o d e l :

Model :(1 )

( 2 )

( 3 )

( 4 )

V T R

B K E - 9 6 5 1 G P I B o a r d ( 1 )

(2)

BVE-9100 • Product Guide Appendix A. Feature List •• 43

Appendix A. Feature List

BVE-9100 — Feature By Feature

CUT DISS WIPE

This Appendix provides comprehensive tables of BVE-9100 features, arranged andgrouped according to functionality. Brief descriptions are provided for each. Allfeatures are also cross-referenced in the index.

Note that all features discussed in this section use Sony terminology. An excellentguide is available that cross-references the names of Sony features with those ofcompetitive editing systems such as CMX and GVG.

Refer to the BVE-9100 Expanded Reference Guide V2.0 (BC-00577) for details.

44 •• Appendix A. Feature List BVE-9100 • Product Guide

System SetupSystem Setup features are required to configure the editor, peripheral devices, andauxiliary devices.

System Setup Features

Feature Description

System Setup Menu Controls application configuration function such ascontrol devices, switcher crosspoint assignments and I/Ocommunications. Setups can be stored in each of the 16EDL bins.

Initialization Menu Controls editing “preferences” such as preroll, postroll,and color framing.

Auxiliary Menu Controls editor-specific functions such as devices andEDL specifications.

Load/Save Saves and recalls system setups to and from the disk.

Self Diagnostics Provides board-level ROM and RAM testing.

Sync Grade For each device controlled, sets the synchronizationtolerance or “window” in which edits will be performed.Typically set to 0 (zero) or frame accurate.

Keyboard Reassignment Provides the ability to re-map keyboard assignments,placing functions on different keys as needed.

Color Framing Adjusts color frame relationship between sources.

User Programmable VDU Provides the ability to customize VDU display andlayout — 16 colors on the screen simultaneously.

Signal Source SelectionThese features allow you to select players, recorders, and auxiliary sources.

Signal Source Selection Features

Feature Description

28 Device Interface Ports Provides ports for up to 28 serial controlled devices.

R (R1-R8) Select from 1 to 8 recorders on line.

P1 - P12 Select from 1 to 12 players (sources) on line.

AUX 1, AUX 2 Assign switcher crosspoints to Auxiliary sources.

Audio Monitor Muting Selectively mutes the desired audio channel(s).


Edit ModeEdit Mode features are the basic tools required for editing.

Edit Mode Features

Feature Description

Insert (V/A1/A2/A3/A4) Selectively enables any individual or combination ofaudio/video channels for editing. Control track ispreserved (clean inpoint, clean outpoint).

Assemble Enables all channels for editing. Control track is re-recorded (clean inpoint, crash outpoint).

1st Edit Special one-button mode that lays down the first edit ona tape that has not been previously recorded with blackand timecode. Controls the VTR’s timecode generator.Also used to prepare videotape for editing.

Split Edit (Audio Base, VideoBase)

Allows audio to precede video, or video to precede audioin an insert edit. Also called an “L” cut. Mode controlsboth split inpoint and outpoint.

Multiple Audio Split-In Allows more than one audio track to be split from video.

Transition TypeTransition Type features allow you to control the video switcher, and select thedesired transition for the current edit.

Transition Type Features

Feature Description

Cut Selects a cut to a source. Dialog allows you to specifythe “to” source.

Wipe Selects a wipe between sources. Dialog allows you tospecify “from” and “to” sources, wipe duration andswitcher pattern number.

Dissolve Selects a dissolve between sources. Dialog allows youto specify “from” and “to” sources, dissolve duration.

Key Selects a key transition. Dialog allows you to specify“background” and “foreground” sources, key type, keyduration, pattern (if wipe key is selected), and delay.

Manual Allows you to specify one or more edit sources, andautomatically disable the audio and video switchers forcomplete manual control.

Switcher Local Mode Provides an override — disables video switcher fromserial control for local (manual) control at the switcher.

Mixer Local Mode Provides an override — disables audio mixer from serialcontrol for local (manual) control at the audio mixer.


Data EntryData entry features are your numeric tools for editing.

Data Entry Features

Feature Description

Mark In, Mark Out Marks source and record inpoints and outpoints.

Mark Split Marks split edit points, where audio leads video or videoleads audio. Marks split inpoints and outpoints.

Mark Speed Conveniently marks speed at which a transport is rolling,for dynamic motion control editing.

Mark Kbrd Grabs a number from a machine, and places it in thekeyboard buffer for transfer to other data registers.

Set In/Out/Dur Sets in (via keypad) inpoints, outpoints, and durations.

Trim In/Out/Dur Trims or adjusts (via keypad) inpoints, outpoints, anddurations.

Back In/Out/Dur Recalls a number from a data register to the keyboardbuffer, for subsequent transfer to another register.

Store Const/Recall Const Stores and recalls individual timecode marks. 10 (ten)constant registers available.

Automatic Time Track Matches to the given record inpoint based on record reelnumber, source reel number and current edit mode.Searches the entire EDL for matching source inpoints.

Recorder Track Matches to the given record inpoint based on record reelnumber and source reel number. Searches entire EDLfor matching source inpoints.

Player Track Matches the recorder to the given source inpoint basedon source reel number. Searches the entire EDL formatching record inpoints.

DMC Learn Data Track Matches into a previously learned DMC timeline,including any combination of speeds and still frames.System matches timecode, inpoint and VTR speed.

Action Track Backtimes one or more devices based on currentposition of sync points within the edit interval.

Time Track Matches to the given record inpoint based on record reelnumber and source reel number. Always matches to thelatest event in the EDL, regardless of recorder inpoint.Also called “tag” or “match-frame.”

Scroll Track Matches to the given record inpoint based on record andsource reel numbers and current highlighted event ofEDL display. Matches several sources if available.

Archive Track Matches to events recorded on secondary “archive” or“cache” recorder.

Fit function Calculates exact transport speed required to fit a givensource segment into a precise duration (or “hole”) on themaster tape.


Preview and ReplayPreview and Replay features provide a tremendous amount of flexibility — allowingyou to get the edit “just right“ prior to recording.

Preview and Replay Features

Feature Description

Auto Preview In/Out/Effect Also called VVV, previews recorder and all sourcesinvolved in the edit. Options allow inpoint, outpoint, oreffect-only preview. Triggers switcher primary andsecondary effects.

Player Preview In/Out/Effect Also called BVB, previews only the sources involved inthe edit. Options allow inpoint, outpoint, or effect-onlypreview. Triggers switcher primary and secondaryeffects.

Recorder PreviewIn/Out/Effect

Also called VBV, previews only the recorder in the edit.Options allow inpoint, outpoint, or effect only preview.Triggers switcher primary and secondary effects.

Switcher Preview Previews the current effect as set up for the switcherand mixer, including memory and timeline functions.Event is performed without VTRs rolling.

Quick Preview Allows Player-only or Recorder-only preview in threeseconds or less, regardless of designated preroll time.

Multi-Edit Preview Previews an entire EDL or segment using the operationalconditions for auto-assembly.

Fly Edit Preview Allows real-time switching of two or more sourcesduring preview. Cuts and dissolves can be performedand an EDL is created as you switch.

Replay In/Out/Effect After an edit is recorded, plays back the event. Optionsallow inpoint, outpoint, or effect only playback.

Sync Play In/Out/Effect Synchronously plays two or more devices. Optionsallow sources to be played synchronously throughinpoint, outpoint, or effect.

Frame Bump During Sync Play mode, advances or retards one ormore devices in relationship to other Sync Play devices.

Go To Preroll Cues selected device(s) to preroll points.

Go To Inpoint Cues selected device(s) to inpoints.

Go To Outpoint Cues selected device(s) to outpoints.

Go To Effect Point Cues selected device(s) to point at which the switchereffect occurs.

Go To Scratch Pad Value Cues selected device(s) to value entered in scratch pad.


List ManagementList Management features provide a set of important tools for manipulating EDLtimecode numbers, individual events, and blocks of events.

List Management Features

Feature Description

Last X A full page “undo” buffer that stores the last fourchanges to the edit screen. Valid after timecode, GPI, ortrigger changes are made in the marks table.

Last Edit A full page “undo” buffer that stores the last fourchanges to the edit screen. Valid after list managementchanges or after initiating any preview mode.

Save Saves current edit screen data to the operational buffer.Works like a “copy” function.

X-Chg Copies all data from the “Save” buffer to the currentedit screen.

Recall Segment Copies only switcher data, timecode points, DMCmemory, GPI functions, and CCR functions from the“Save” buffer to the current edit screen.

Recall Recall an event (a page of edit information) frommemory.

Correct Places a recalled (and revised) edit back into the EDL.

Insert Inserts a new edit at a specific point in the EDL.

Delete Deletes an edit or block of edits from the EDL.

Move Moves an edit or block of edits within a single EDL bin.

Copy Copies an edit or block of edits in the EDL, in a singlebin or between bins.

Ripple Pulls up a block of edits to fix a “gap” in the EDL, orpushes down a block of edits to avoid an overlap.Typically used after a “Delete” or “Insert” operation.

Renumber Renumbers an individual edit or block of events. Allowseditor to partition a program by scene number.Timecode is not affected.

Automatic clean-up When enabled, automatically eliminates over-recordingsin the EDL. Trims the outpoint of the previous edit tomatch the inpoint of the new edit.

Cleanup overlaps Manual list-management mode that eliminates over-recordings in the EDL. Trims the outpoint of theprevious edit to match the inpoint of the new edit.

Save/Load EDL Saves and recalls EDLs to/from disk. Pause and restartfunctions are standard.

Note Turns keyboard into “typewriter,” allowing entry ofnotes and comments to a selected EDL edit. Notesappear above the event.

Modify Reel Number Changes source or record reel numbers in the EDL.


List Management Features (continued)

Feature Description

Modify Block Number Renumbers a selected block of events.

Modify Edit Mode Changes the edit mode (V, A1, A2, A3, A4) of theselected event or block of events.

Modify Recorder Time Ripples record timecodes in the EDL.

Modify Player Time Ripples player (source) timecodes in the EDL.

Sort by Block Numbers Sorts EDL bin based on block numbers (ascending).

Sort by Event Numbers Sorts EDL bin based on edit numbers (ascending).

Sort by Timecode (A-mode) Sorts EDL bin based on recorder timecode (ascending).

Sort by Timecode (B-mode) Sorts an EDL bin in ascending order based on reelnumbers. Secondary sort field is recorder timecode.

Sort by Timecode (C-mode) Sorts an EDL bin in ascending order based on reelnumbers. Secondary sort field is source timecode.

Scroll Edit (Manual) Controls EDL display position via cursor keys or the jogdial.

Scroll Edit (Automatic) Controls EDL display position based on currenttimecode position of the recorder.

Trace, Quick Trace Locates “original” source reel timecode numbers acrossmultiple EDLs.


Learn ModesLearn modes allow the editing system to memorize and store functions that youperform manually on peripheral devices such as switchers, mixers, and transports.

Learn Modes

Feature Description

Player Learn (DMC Learn) Learns the transport motions of the selected VTR,including speed changes, ramps, TBC freezes, TBCadjustments, and other transport modes. Entiresequence is stored in the EDL.

Switcher Learn Learns live operations performed on the video switcher,including crosspoint and M/E selections, auto transitionsand memory triggers. Editing system creates a sequencelist in the EDL based on the live switcher changes.

Mixer Learn Learns live operations performed on the audio mixer,including crosspoint selections, auto transitions andmemory triggers. Editing system creates a sequence listin the EDL based on the live switcher changes.

Color Corrector Learn Learns operations performed on the color corrector.Mode is indexed based on the source reel. Entiresequence stored in the EDL.

Create Event In the current edit page, allows you to create or modifyinformation within a mixer memory, switcher memory,or DMC memory.

Delete Event In the current edit page, deletes a specific event from themixer memory, switcher memory, or DMC memory.

Modify Event In the current edit page, modifies a specific mixermemory, switcher memory, or DMC memory.

User-Programmable Keys Provides 16 user-programmable (macro) keys, forlearning sequences of keystrokes.


Recording FeaturesOnce an event is previewed, a variety of recording features are available.

Recording Features

Feature Description

Automatic Recording Records current edit in the Edit Screen, or a single edithighlighted in the EDL.

Manual Edit Allows you to place the recorder into edit mode.

Record Off Allows you to manually exit the automatic record ormanual record mode at a point other than theprogrammed out point. Outpoint is clean, and the eventis stored in the EDL.

Auto-Assembly (A Mode) Records multiple events in the selected EDL bin, insequential order. System prompts for unmounted reels.Pause and resume modes are standard. Also calledsequential assembly.

Auto-Assembly (B Mode) Records events in the selected EDL bin, in sequentialorder. System skips unmounted reels. Pause andresume modes are standard. Also called checkerboardassembly.

Auto-Assembly (C Mode) Continuous recording based upon operational conditionsof pre-cue and source availability.

Look Ahead Control Pre-cues sources to minimize auto-assembly time.

Background Recording System allows you to perform an auto-assembly in thebackground while you are manually constructing an editinto the EDL memory.

Fly Edit Allows real-time switching of two or more sourcesduring recording. Cuts and dissolves can be performedand an EDL is created as you switch.

Multi-Recorder Allows up to eight recorders simultaneously. Supportsoffset timecodes.

Temporary Recorder Provides ability to change recorders quickly and easily.This function is often called “swapping” recorders. Allpreview functions are automatically re-assigned.

Temporary Crosspoint Assign Allows temporary crosspoint assignments, on edit-by-edit basis. All changes are stored in the EDL. Easymode is provided to change back to defaults.

Digital Process Delay Compensates for a video delay through digital devicessuch as DME or color correctors. Adds audio delay forthe selected source.

GPI Control Provides four standard GPI output ports, expandable to36 output ports. Comprehensive trigger capability and“test” mode is standard, all GPI events stored in EDL.Each expansion GPI can be triggered 8 times per event.


Recording Features (continued)

Feature Description

Master/Slave Control Provides ability to define sync relationships betweendevices, where one tracks the other. Typically used forkey matte and fill requirements where sources arepresent on two (or more) reels, and must track in sync.

Auto “B” Roll When requirement for B-roll is detected, systemautomatically dubs source to designated B-roll recorder,and subsequently rolls that recorder as the “B” playbacksource. Also known as “cache” recording.

Pre-Read Provides control over digital VTR’s ability to read digitalinformation (both audio and video) off tape — prior towriting the data back on tape. Advanced automatic Pre-Read enable modes are included.

Disk ManagementA variety of features are provided for managing disks, EDLs, and files.

Disk Management Features

Feature Description

File List Print Provides ability to print an EDL.

File Copy, Print, Rename Provides ability to copy, print, and rename file(s).

File Delete Provides ability to delete file(s) from disk.

Volume processing Provides ability to copy, rename, and initialize (format)the disk.

BVE-9100 • Product Guide Appendix B. Related Resources •• 53

Appendix B. Related Resources

Related Resources

CUT DISS WIPE

The following resource information is included in this Appendix:

• Printed Media

• Audio/Video Media

Printed MediaUse the following printed publications for additional information on the BVE-9100:

• Refer to the BVE-9100 User’s Guide Volumes 1 and 2 forcomprehensive BVE-9100 operating instructions.

P/N: 3-172-737-03 (Volume 1)3-172-738-03 (Volume 2)

• Refer to the BVE-9100 Expanded Reference Guide V2.0 for a detailedfeature-by-feature discussion of all BVE-9100 modes. The guideincludes cross-references to CMX and GVG features.

P/N: BC-00577

• Refer to the BVE-9100 Installation and Maintenance Manual for adiscussion of all installation and maintenance issues.

P/N: 3-172-757-02

54 •• Appendix B. Related Resources BVE-9100 • Product Guide

• Refer to the BKE-9402 Installation and Maintenance Manual forcomplete installation and maintenance information on the BKE-9402Programmable Control Panel. Comprehensive schematics, pinassignments, and system diagrams are included.

P/N: 3-187-611-01

Audio/Video MediaUse the following audio/video publications for additional reference information on theBVE-9100:

• Refer to the BVE-9100 Demonstration Video Tape for an in-depthdemonstration of the BVE-9100 system.

P/N: BC-00556

BVE-9100 • Product Guide Appendix C. Sales and Service •• 55

Appendix C. Sales and Service

General Information and Reference

CUT DISS WIPE

1 2 3

654

A B C D E F

M N OJ K LG H I

The following information is included in this Appendix:

• Regional Sales Offices

• Regional Service Centers

• National Parts Centers

• Emergency Response System

• SUPPORTNETSM

• SOFTWAREPLUSSM

56 •• Appendix C. Sales and Service BVE-9100 • Product Guide

Regional Sales OfficesSony Regional Sales Offices are located in the following areas:

• Northeast Regional Sales Office

123 W. Tryon Ave.Teaneck, NJ 07666Main Number: (201) 833-5300Fax Number: (201) 833-5850

• Southeast Regional Sales Office

3175 A. Northwoods ParkwayNorcross, GA 30071Main Number: (770) 263-9888Fax Number: (770) 441-8870

• Midwest Regional Sales Office

1200 North Arlington Heights RoadItasca, IL 60143Main Number: (708) 773-6000Fax Number: (708) 773-7623

• Southwest Regional Sales Office

8400 Esters Blvd., Suite 500Irving, TX 75063-2214Main Number: (972) 915-3100Fax Number: (972) 915-3235

• West Regional Sales Office

10833 Valley View StreetCypress, CA 90630-0016Main Number: (714) 229-9100Fax Number: (714) 229-4159


Regional Service CentersSony Regional Service Centers are located in the following areas:

• Northeast Regional Service Center

123 W. Tryon Ave.Teaneck, NJ 07666Main Number: (201) 833-5300

• Southeast Regional Service Center

3175 A. Northwoods ParkwayNorcross, GA 30071Main Number: (770) 263-8016

• Midwest Regional Service Center

1200 North Arlington Heights RoadItasca, IL 60143Main Number: (708) 773-6037

• Southwest Regional Service Center

8400 Esters Blvd., Suite 500Irving, TX 75063-2214Main Number: (972) 915-3220

• West Regional Service Center

10833 Valley View StreetCypress, CA 90630-0016Main Number: (714) 229-4100


National Parts CentersSony National Parts Centers are located in the following cities:

• San Jose, CA

For Broadcast parts:(800) 538-7550

• Kansas City, MO

For Professional Audio parts:(800) 331-6679, (800) 654-0962 (in MO)

For Business/Industrial parts:(816) 891-7550, (816) 891-7435 (after-hours)


Emergency Response SystemUse Sony’s Emergency Response System for after-hours technical support.

1. Call (408) 435-8910

2. Using a touch-tone phone, select the desired primary category from thefour (4) menu selections, then the appropriate secondary category. If aselection is not made from a touch-tone phone, the system will terminatethe call.

Menu 1: Technical Assistance for Broadcast and Audio/VideoProduction Products

1 Digital Video or Type C Recorders

2 Betacam® or Umatic® Products

3 Video Editors or Switchers

4 Library Management System™ or Betacart® Systems

5 Professional Audio

6 Camera or Monitor Products

7 High Definition Video Systems

8 Repeat Primary Menu Selections

Menu 2: Technical Assistance for Other Business and ProfessionalProducts

1 Videoconferencing Systems

2 Jumbotron® Systems

3 Medical Systems

4 Repeat Primary Menu Selections

Menu 3: Emergency Parts System

Menu 4: Repeat Primary Menu Selections

3. When prompted, leave your name, company, a telephone number whereyou can be reached, model number, and a brief description of theproblem. A Sony product specialist will return your call within 60minutes.


SUPPORTNETSM

The SUPPORTNETSM program brings all the expertise, responsiveness, and commitmentof the company together in a comprehensive package to ensure continued customersatisfaction. In addition to Time and Materials (T&M) service, which is available tocustomers who require support on a per-call basis, a variety of programs are availableto meet varying needs:

• UpTime APS

Improves uptime and ease of care, thanks to professional on-sitehardware support by Sony engineers and optional application support.

• Technical Education

Sony technical training enhances the customer’s knowledge of the Sonyproducts and their maintenance. This enables the customer to take amore active role in maximizing the potential of the product.

• Technical Publications

Technical Bulletins are published monthly with timely informationregarding the servicing and maintenance of Sony products. A CD ROMis available with all Technical Bulletins, parts pricing, and selectedexploded diagram views. Tech manuals are also available.

Optional software Application Support provides the following:

• Maintenance and enhancement releases. This item does not includesoftware sold separately or product options.

• Telephone support for software and application issues.

• Discounts on selected new and optional software products.

• Automatic enrollment in SOFTWAREPLUSSM service program.

SOFTWAREPLUSSM

Purchasers of Sony Production Systems products are automatically enrolled into theSOFTWAREPLUS

SM program. This service includes the following:

• Notification of software releases

• Tracking of each customer’s unique system configuration and softwarerequirements.

• Access to the latest software release information, including currentversions, features, and pricing.

• Product registration for warranty software upgrades.

• Authorized upgrade pricing.

The telephone number for SOFTWAREPLUSSM is (408) 955-6300.

BVE-9100 • Product Guide Glossary •• 61

Glossary

Archive RecorderAlso known as “cache” recorder. Special designation for a recorder in which allevents are recorded sequentially, without overlaps. Used to preserve each layerduring complex multi-layer sequences.

B-rollEssentially a copy of a clip or a sequence. Without the availability of pre-read, the“to” and “from” sources in a transition must be on separate reels. If they are not, a B-roll must be made in order to perform the transition.

CleanupA list management tool that cleans up problems in the EDL, including overlaps andgaps. Cleanup is used to streamline the auto-assembly and re-edit process formaximum efficiency, guaranteeing that the numeric EDL matches the visual program asrecorded on tape.

ClipAlso know as a “segment” or “scene.” Describes a continuous length of sourcefootage, long or short, the duration of which is defined by an inpoint (head frame) andan outpoint (tail frame).

Distributed ProcessingA software technique whereby the master processor (Main CPU) delegates lessertasks to other CPU's in the system, thereby freeing its time for more important work.

DMC Motion MemoryAlso called Dynamic Motion Control. The ability for the BVE-9100 editing system tolearn (and repeat) the precise playback speed and direction of a VTR during a slowmotion sequence. Both simple events, with a single slow-motion speed, and complexevents, with ramping speed, freezes, and direction changes fall into the DMC category.

E-FileThe Sony trademarked system for switcher effects memory.

Edit Data PageAlso known as the Edit Screen, the BVE-9100’s main operating menu in which theeditor sets up events and transitions, marks timecode, and manages the EDL.

62 •• Glossary BVE-9100 • Product Guide

EditorAn electronic device for controlling and synchronizing a variety of broadcastproduction components with frame accuracy. Used to produce television programs.

EDLEdit Decision List. A single file stored on the editing system’s hard disk that containsinformation for each event used in a video program. When re-editing is required, thisinformation is used to re-create events, exactly as they were initially recorded. EDLevents are comprised of data fields, such as source and record VTR inpoints,outpoints, reel numbers, mode (V, A1, A2), transitions (Cut, Dissolve, Wipe), andperipheral device effects data. There can be multiple EDL files on disk.

EthernetA computerized network (and system of protocols and commands) for transferring databetween electronic devices.

GPI (General Purpose Interface)A port on the editing system that can be triggered with frame-accuracy in an edit event.Typically used to activate a function on a peripheral device that does not have serialcontrol capability.

GUIGraphical User Interface. A term that describes a status display based on graphics andicons, rather than strictly on numbers and letters.

Initialization MenuA secondary BVE-9100 menu used to set up EDL specifications and overall system“preferences” such as preroll and color framing.

InterfaceA set of software instructions that allows the editing system to control a peripheraldevice such as a VTR, ATR, DVE or switcher. The better the interface, the greater theease with which the operator can assemble a program.

KeyframeIn a digital effects device, a point along a timeline where an action or change occurs.In a DVE, such as the DME-7000, keyframes occur at specific points of imagemanipulation. The BVE-9100 controls keyframe timelines for a variety of devicesincluding the DME-series digital effects units and DVS-series switchers.

List managementA set of software tools for manipulating EDL timecode numbers. Tools include theability to move, copy, and renumber events (and blocks of events), clean overlaps andsort the list.

BVE-9100 • Product Guide Glossary •• 63

M/EMix/Effects or Mix Effects Amplifier. The portion (or "bank") of a video switcherwhere video signals are processed to select sources and create mixes, fades, wipes,keys, and other special effects.

Master/Slave ModeAlso known as “Sync Jog.” A method for locking two or more source devicestogether in an edit event. Typically used in situations where the matte is on one reel,and the fill is on another.

Peripheral deviceAny device connected to the BVE-9100 via serial communications or GPI. Categoryincludes VTRs, ATRs, Video Switchers, Audio Mixers, Color Correctors, DVEs, andDDRs.

Pre-ReadAlso known as “read before write.” The ability for a digital VTR to read digitalinformation (audio and video) off tape - prior to writing the data back on tape.

Setup MenuA secondary BVE-9100 menu used to set up devices, crosspoint assignments and I/O(input/output) communications.

Status reportingA system of bi-directional communications that allows the panel status of peripheraldevices to be reported to (and stored in) the BVE-9100’s EDL in real-time.

TBCTime Base Corrector. A device used to stabilize a VTR's unstable image. Includescontrols for adjusting the brightness, black level, color hue, and color saturation of thevideo playback.

Time TrackA powerful, software-based feature for finding matching video frames in the EDL.Match frames enable you to synchronize machines and perform clean, seamlesstransitions in a program. The BVE-9100 has a variety of Time Track modes.

TimecodeA numeric method for identifying video frames with precision. Each frame of video isassigned an unique 8-digit number (hours, seconds, minutes, frames). Enables precisematch-frame editing transitions.

TraceA list management tool that traces back to “original” source reel timecode numbersacross multiple EDLs. Let’s say that master tape #1 is a rough cut. If master tape #1is next used as a source in the second cut (producing master tape #2), the original

64 •• Glossary BVE-9100 • Product Guide

source reel timecodes are one EDL generation back. If the process is repeated again,the original numbers get farther away, but they’re not lost. If you want to assemble theshow using the original source reels, the trace program is used to “recover” theoriginal source in and outpoints.

BVE-9100 • Product Guide Index •• 65

Index

1

1st Edit 41

A

Abekas 5, 19Action Track 42Advanced Operating Program 16, 23Ampex 5, 17

AVC Vista 19Archive 12, 14

recorder 14track 42

Assemble 41Assignment, record and source 11ATR 5Audio

control 7monitor muting 40

Audio/Video Media 50Auto

B-roll 13, 48cache 13pre-read 12preview in/out/effect 43

Auto-AssemblyA Mode 47B Mode 47C Mode 47

Automaticclean-up 44recording 47time track 42

AUX 1, AUX 2 40Auxiliary Menu 40AVC Vista 19

B

B-roll 13Back In/Out/Dur 42Background Recording 47Basic

components 16

tools 4Bins 6

management 10setup 10

BKE-9002 23BKE-9011 23

connector specifications 30BKE-9014 23BKE-9102 23BKE-9400A 23BKE-9401 23BKE-9402 5, 23BKE-9410 23BKE-9600 21BKE-9651 21, 30, 34BVB preview 43BVE-9000 1

conversion 24BVE-9002 16BVE-9011 16BVE-9014 16BVE-9100 1, 23

basic components 16benefits 3chassis front view 27chassis rear view 28chassis specifications 29connectors 30customer interconnection chart 38demonstration video tape 50expanded reference guide V2.0 49, 50features 3installation and maintenance manual 49keyboard diagram 26network 20system interconnection chart 37user’s guide 49

BZE-9101 16BZE-9102 23BZE-9601 23BZE-9602 23BZE-9603 23BZE-9604 23BZE-9605 23BZE-9606 23BZE-9611 23

C

Cable 20Cache 13

auto 13head 13tail 13

Capability 10Chassis

66 •• Index BVE-9100 • Product Guide

components 27dimensions 29external dimensions 29front view 27power 29rear view 28weight 29

Cleanup 6overlaps 44

Colorcorrector learn 46display 8framing 40VDU Out, chassis connector specifications 32VDU Out, pinouts 32

Connectors 30Convergence 17Copy 44, 48Correct 44CPU 4Create Event 46CTG-31V 23Customer interconnection chart 38Customize environment 6Cut 41

D

Dataentry 42page 5

DDR 11, 14Dedicated keyboard 7, 17Delete 44

event 46file 48

Demonstration Video Tape 50Device Interface Ports 40Diagnostics 40Digital Process Delay 47Dimensions

chassis 29chassis, external 29keyboard 26

Disk Management 48Display

color 8Dissolve 41Distributed processing 4DMC Learn Data Track 42DME 5DME-5000 5DMX-E3000 20DVE 5Dynamic Motion Memory 12

E

E-Files 6Edit

data page 5decision list 4manual 47mode 41mode, modify 45preferences 5

Editingcontrol unit (NTSC) 23keyboard (Dedicated) 17keyboard (Qwerty) 23

EDL 4capability 10capacity 6memory 6timecode 6

Emergency Response System 55ESAM II 20Ethernet

AUI interface 20I/O Card 20, 23

Eventdelete 46modify 46

Expanded Reference Guide V2.0 49, 50Expansion 5

F

Featureand benefit 3list 39

Filecopy, print, rename 48delete 48list print 48server 20

Fit function 42Flexibility

menu 5system 5

Floppy disk 6Fly Edit 47

preview 43Form, request 23Frame Bump 43

G

General Purpose Interface 7Go To

effect point 43inpoint 43


outpoint 43preroll 43scratch pad value 43

GPIboards 21, 30, 34connector specifications, BKE-9651 34connector specifications, chassis 34control 47expansion 21, 23pinouts 34ports 7

Graham-Patten 5ESAM II 20

GVG 5Kadenza 19switchers 19

H

Hard Disk Unit 6, 16, 23Head Cache 13

I

IDC 16, 21, 23, 34Initialization Menu 5, 40Insert 41, 44Installation and Maintenance Manual 49Intelligent Device Controller 16, 21, 23, 34Interconnection chart 37, 38Interface 5, 6

ports 40switcher/mixer/monitor switcher 23

K

Key 41assignments menu 10

Keyboarddedicated 7, 17, 23diagram 26dimensions 26flexibility 10power 26Qwerty 7reassignment 40specifications 26sub 7, 17

L

Lastedit 44X 44

Layout menu 10Learn 11

color corrector 46DMC events 12modes 46

Listmanagement 6, 44print 48

Load/Save 40Local Mode 41Look Ahead Control 47

M

Macro Keys 46Manual 41

edit 47Mark

in, out 42kbrd 42speed 42split 42

Master/Slavecontrol 48mode 12

Match-frame 10Memory 11

motion 12Menu

flexibility 5, 10initialization 5key assignments 10layout 10setup 5

Microprocessor 4Mixer

control program (Sony/GPS) 23learn 46local mode 41

Modifyblock number 45edit mode 45event 46player time 45recorder time 45reel number 44

Monitor 23cable 23muting 40

Motion memory 12Move 44Multi

camera ISO 12edit preview 43interface card (4 port) 23recorder 47

Multipleaudio split-in 41


bins 6Muting 40MXP-S390 20

N

National Parts Centers 54Network 20Note 44

O

One disk solution 4Order guide 22

P

P1 - P12 40Paltex 17Parts 54Peripheral control 5Pinouts

BKE-9011 30color VDU out, chassis 32GPI 34printer 32RS-422 30

Playerlearn (DMC learn) 46preview in/out/effect 43track 42

Powerchassis 29keyboard 26tools 9

Pre-Read 12, 48auto 12

Preferences 5Preview

and replay modes 43BVB 43

Print 48Printed Media 49Printer

connector specifications 32pinouts 32

Programmable Control Panel 9, 17, 23Publications 49

Q

Quickpreview 43trace 45

Qwerty keyboard 7

R

R (R1-R8) 40Rack mounting 27RCC-10G 23RCC-30G 23RCC-5G 23Read before write 12Reassign keyboard 40Recall 44

segment 44Record

archive 14assignment 11off 47temp 11

Recorderpreview in/out/effect 43track 42

Recordingautomatic 47features 47

Regionalsales offices 52service centers 53

Related Resources 49Rename 48Renumber 44Repeatability 10Replay In/Out/Effect 43Request Form 23Response System 55RGB status monitor 18, 20Ripple 44RS-422

cables 23connector specifications 30devices 20pinouts 30


S

Salesand Service 52offices 52

Save 44Save/Load EDL 44Scroll

edit, automatic 45edit, manual 45track 42

Security 10Self Diagnostics 40Service Centers 53Set In/Out/Dur 42Setup 40

menu 5, 40Signal Source Selection 40Slow motion 12Snapshot 11Software 6, 16SOFTWAREPLUS 56Sony

BVS-series 18DME-5000 5DMX-E3000 20DVS-series 18VTRs 5

Sortby block numbers 45by event numbers 45by timecode (A-mode) 45by timecode (B-mode) 45by timecode (C-mode) 45

Source assignment 11Specifications

BKE-9011 connector 30chassis 29color VDU out, chassis 32GPI connector, BKE-9651 34GPI connector, chassis 34keyboard 26printer 32RS-422 connector 30

Split Edit 41Status

display monitor 18reporting 9RGB monitor 18, 20

Store Const/Recall Const 42Sub Keyboard 7, 17, 23SUPPORTNET 56SVGA Monitor 18Switcher

control program 18control program (Abekas) 19, 23

control program (AVC Vista) 19, 23control program (GVG 200) 19, 23control program (GVG Kadenza) 19, 23control program (GVG/Sony) 19, 23control program (Sony DVS/BVS series) 23learn 11, 46local mode 41memory 11preview 43

Syncgrade 40jog 12play in/out/effect 43

Systemcables 20flexibility 5interconnection chart 37interfaces 5RS-422 Cables 23setup 40setup menu 40software 6

T

Tail Cache 13Technical

education 56publications 56

Temp record 11Temporary

crosspoint assign 47recorder 47

Time and Materials 56Time Track 10, 12, 42

automatic 42modes 10

Toolsbasic 4power 9

Trace 6, 45quick 45

Transition Type 41Trigger events 11Trim In/Out/Dur 42

U

UI 6UpTime APS 56User

interface 6programmable keys 46programmable VDU 40

User’s Guide 49


V

VBV 43Vista 19Volume processing 48VTR 4VVV 43

W

Wipe 41

X

X-Chg 44

BVE-9100 • Product Reference Guide

Part Number BC-00583

Documents

˝ˆ˛ˇ BVE-9100 - BroadcastStore.com · ˝ˆ˛˙ BVE-9100 • Product Guide Contents • i Contents Introduction 1 About This Guide