Slips, Trips, and Falls

DISCLAIMER: The contents of this document are intended only for the informational use of the addressee. The information contained herein is not intended as, nor does it constitute, specific legal or technical advice to the reader. Any information or recommendations contained herein are provided to the addressee for usage at their own discretion. Neither Signal Mutual Indemnity Association Ltd., its Members, Managers or Signal Administration, Inc. and/or their employees accept liability whether in tort, negligence, contract, or otherwise, to anyone for any lack of technical skill, completeness of recommendations, or analysis of issues associated with the discussion of topics set forth herein. No responsibility is assumed for the discovery or elimination of unsafe conditions. Compliance with any recommendations herein should not assume your compliance with any federal, state, or local law or regulation. Additionally, the information contained herein does not constitute and shall not be construed to reflect the adoption of any coverage position by Signal Mutual Indemnity Association Ltd., its Members, Managers or Signal Administration, Inc. and/or their employees.

IntroductionThere’s been so much information about

slips, trips, and falls that many people are no longer paying attention.

Slips and falls were the major causes of injuries in the early days of safety.

There are cases where people were deliberately pushed down stairs. There have been a wide range of accidents in the workplace from every conceivable cause.

IntroductionThis even includes running into doors or

doors running into people.Jumping from elevated surfaces has

caused quite a few injuries.And every type of slip and fall from ladders

to slippery floors, debris on the floor or working surfaces.

No improvement is noticeable.

Today’s Injury StatisticsWith today’s technology, injury statistics

demonstrate where we went wrong, and even with excellent safety and health departments, we still experience slip and fall incidents.

What’s the magic bullet? New floor surfaces. State of the art shoes.

What’s the answer? We believe it is more training. And that everyone accepts responsibility for working and acting safely.

Who would have thought of that?

Overview of CourseLet’s look at how we’re going to approach

today’s course.First, we want to review some of the ways

people trip and fall.Secondly, we want to review basic

prevention techniques.Thirdly, we’d like to encourage you to get

on the safety bandwagon for preventing slips, trips, and falls.

Causes of Slips, Trips, and FallsWhen you think of ladders, uneven

surfaces, and of course slippery surfaces such as water, ice, and grease, you can visualize the cause of accidents.

OSHA states that about 35 percent of the majority of workplace accidents are caused by slips, trips, and falls.

Causes of Slips, Trips, and FallsFalls can cause severe injuries such as

broken hands and arms, back injuries, strains to muscles and ligaments, and even death.

Slips, trips, and falls happen when working with ladders, platforms and heights. Nothing good can come from slips, trips and falls.

Causes of Slips, Trips, and FallsRemember, these types of accidents have

been around for a long time. So it’s nothing new. However, there is a new concentrated effort to eliminate slips, trips, and falls.

FallsAbout 60 percent of falls

are a result of slips and trips. The remaining 40 percent are falls from heights, falls from ladders, roofs, and stairs, or from jumping to a lower level.

SlipsSlips happen when there is

too little friction or traction between footwear and the walking surface.

Common causes of slips are wet or oily surfaces, occasional spills, weather hazards, or unanchored rugs or mats and flooring, and walking surfaces that do not have the same degree of traction in all areas.

TripsTrips happen when your foot collides by striking or hitting

an object, causing you to lose your balance and then fall.Common causes of trips are:o Obstructed viewo Poor lightingo Clutter in your wayo Wrinkled carpetingo Uncovered cableso Bottom drawers not being closedo Uneven steps and walking surfaces

ReviewA trip occurs when a person’s foot comes

in contact with an object that’s in their way or drops to a lower level unexpectedly, causing them to be thrown off balance.

A slip occurs when there is too little traction between footwear and the walking surface.

A fall occurs when you’re too far off balance.

Prevention TechniquesBoth slips and trips result from some kind

of unintended or unexpected change in the contact between the feet and the ground or walking surface.

This shows that good housekeeping, quality of walking surfaces or flooring, selection of proper footwear, and appropriate pace of walking are critical to preventing fall accidents.

Prevention TechniquesWhat are some basic ways you can

prevent slips and trips?o Install light sources that are sufficient for your

task, oUse a flashlight if you’re entering a dark room

where there’s no light oEnsure that things you’re carrying or pushing do

not prevent you from seeing obstructions or spills

HousekeepingThe first and most important level in preventing

falls due to slips and trips is good housekeeping which includes;oCleaning all spills immediatelyoMarking spills and wet areasoMopping or sweeping debris from floorsoRemoving obstacles from walkways and keeping

them free of clutteroSecuring mats, rugs and carpets that don’t lay flatoAlways close file cabinet and storage drawers

Housekeeping Other housekeeping tasks are:

o Cover cables that cross walkways.o Keep work areas and walkways well lit.o Replace used light bulbs and faulty

switches.

Without good housekeeping practices, any other preventive measure such as installation of special flooring, appropriate footwear, or training in walking and safe falling, will never be fully effective.

FootwearIn workplaces where floors may be oily, wet,

or if workers spend considerable time outdoors, prevention of fall accidents should focus on selecting proper footwear.

Since there’s no footwear with anti-slip properties, consulting a shoe manufacturer is highly recommended.

Proper fitting footwear increases comfort, and prevents fatigue, which can improve safety for the employee.

FootwearIt’s important to remember that safety is

everybody’s business.However, it is the employer’s responsibility

to provide a safe work environment for all employees.

The most important protection is to wear the proper footwear for your work and environment.

FootwearIn most occupations, the shoes or boots

should provide three major types of protection.oSoles and heels should be slip resistantoThe toe of the shoe should resist crushing injuriesoThe shoe should support the ankle

FootwearLeather covering the foot and ankle portion of

the foot is preferred in most work environments.

However, when working in wet environments, or around chemicals, oils, greases, or pesticides, boots made of polyvinyl chloride (PVC), a blend of PVC and polyurethane, or neoprene should be used.

Rubber is satisfactory for wet conditions but not with pesticides or petroleum products.

Behaviors That Lead to FallsIn addition to wearing the wrong footwear,

there are specific behaviors which can lead to slips, trips, and falls.

Behaviors That Lead to FallsWalking too fast or running can cause

major problems that can lead to slips, trips, and falls.

Distractions, not watching where one is going.

Carrying materials which obstruct view.Wearing sunglasses in low light areas.Failure to use hand rails.

Behaviors That Lead to FallsThese and other behaviors, caused by a

lack of knowledge, impatience, or a lack of good habits developed from past experiences, can lead to falls, injuries, or even death.

Makeshift ladders, chairs, boxes, and barrels should never be used as substitutes for a ladder. The risk of injury is far too great.

Falls from Vehicles and EquipmentDeath or serious injury is a frequent result of

extra riders falling from tractors, equipment, or the bed of a truck.

The safe way to avoid falls from vehicles or equipment is to not allow riders.

Falls from Vehicles and Equipment

Practice the three point system on entry and exit. This system can significantly reduce the chances of injuring yourself through a slip or fall while climbing ladders or while entering or exiting a vehicle.

The three point system means that three of your four limbs are in contact with the ladder or vehicle at all times - either one hand and two feet or two hands and one foot.

Falls from Vehicles and Equipment

Only one limb is in motion at any time with the three point system.

When getting off the bed of a truck or wagon, or any similar level, step down backwards.

Never jump or fall down forward.

Falls on StairsStairwells should be well lighted with sturdy

hand rails on both sides.Persons using the stairwell should have

one hand free to be able to use the hand rail.

All the steps should have the same rise and depth with visible edges.

They must be kept free of grease, oil, and obstacles which could cause slips and trips.

Falls on StairsWhenever possible, avoid carrying bulky or

heavy objects which obscure your vision and/or require the use of both hands.

Carry smaller, lighter loads and make more trips, or obtain help with the load.

LaddersLadders cause a great

number of injuries.Never stand on the top two

steps of a stepladder—that’s just too dangerous and causes an unsafe shift in the center of gravity of the ladder.

Don’t lean past the rails of the ladder as this creates instability.

LaddersWe call this the “belt buckle rule.” Don’t

lean past your belt buckle, for safety.Naturally, don’t use a metal ladder when

working on or near electricity. It’s a great risk of electrocution or getting a shock that can throw you off the ladder.

LaddersWith straight ladders, you may recall the

old 4 to 1 ratio for setting up straight ladders.

While still applicable, it falls short of the best way to ensure that the ladder is properly set up for safety.

LaddersThere are three basic requirements for

extension ladder setup.First, the top of the ladder must extend three

feet or three rungs above the point of contact with the structure.

Secondly, it must be set up at the precise angle of 75.5 degrees to provide the proper angle for climbing.

Lastly, an extension ladder verification device is recommended to achieve this angle with accuracy.

Fall Protective DevicesWorkers at high elevations,

such as ladders, platforms, and catwalks, should be protected from falling by some kind of fall protective device.

This could be a protective cage, a lifeline, lanyard, safety belt or harness.

Fall Protective DevicesThere are numerous devices on the market. The system should provide maximum

protection but it should also be reasonably comfortable and not restrict the worker’s necessary work activity.

Suppliers of safety equipment can provide information on the correct system for your workplace and should provide instruction on its safe use.

Signs and StripingSafety signs to remind people of slip, trip, and

fall hazards are certainly always helpful.Particularly where hazards cannot be removed

or corrected, such signs should be changed frequently.

Signs and StripingYellow striping to identify walking and

working areas are most effective if their meaning is enforced.

Striped areas should mean that no object should be placed in these areas.

Dropped and spilled materials should be removed immediately.

ConclusionEstablished policies and practices can be

implemented to significantly reduce the number of injuries and deaths due to slips, trips, and falls.

Much like being a defensive driver, to avoid accidents, one must also be a safe walker to avoid slips, trips, and falls.