Copying ID46 transponder chip by CN900 ID46 CLONER BOX

http://www.vipprogrammer.com/cn900-auto-key-programmer-cn90

0-transponder-programmer-893

CN900 remote transponder chip Programmer is used to copy key

ID46 transponder chip. With CN900 46 Cloner box, you can copy

remote keys faster and easily. Here, vipprogrammer.com share the

detailed instruction for Clone ID46 transponder chip by CN900 ID46

CLONER BOX, and guide you how to use CN900 key programmer

and 46 cloner box to copy keys. Hope it will helpful to you.

How to connect the CN900 key programmer with 46 cloner box to

copy ID 46 chips? Here is the detailed instruction:

Must car key programming Equipment:

CN900 key programmer

46 cloner box

Step 1: Instruction for CN900 key programmer components:

1) This is the TPX4 chip, what is this chip used for? This TPX4 chip is

used to collect data.

2) This is the chip shell

3) Put the TPS4 chip into the shell, then you will see the photo like this:

Step 2: Use CN900 to copy chips

1) Connect CN900 Key programmer with 46 cloner box ready, then turn on

the power of CN900 key programmer.

2) Plug the original key into CN900 key programmer, and click “read©”

button, after a few seconds, you will see the following information on

the screen of CN900 key programmer:

3) use the pen to click “DECODE” button.

4) Remove the original key from CN900 key programmer, then plug the TPX4

chip into CN900 key programmer

5) When you see the information displayed as the screen of the first

following photo, take the original key and TPX4 chip to your car. TPX4

chip shold be closed to the original key. Plug the original key into the

ignition switches. Power on — power off — pull it out. Repeat this

operation for 4 times. Data collection is over.

6) After you collect the data ready, put TPX4 on CN900 key programmer like

the photo, then click “OK” button.

7) After you finish these steps, you will see ” Reinsert the original

key please” just same shown as the photo. Remove TPX4

chip,[obd2express.co.uk] then insert the original key to CN900 key

programmer, finally click “OK” button. After a few seconds, you will

see “decoded successfully” prompt on the screen.

http://blog.obd2express.co.uk/wp-content/uploads/2015/08/cn900-key-programmer-components-instruction-19.jpg

8) A few seconds of this prompt later, you will get the following

information:

9) Remove original key, then put CN3 chip on CN900 key programmer, click

“Copy” button. A few seconds later, you will get “copy success” prompt.

It means that CN3 chips has copied the original key data successfully.

http://blog.obd2express.co.uk/wp-content/uploads/2015/08/cn900-key-programmer-components-instruction-24.jpg

http://blog.obd2express.co.uk/wp-content/uploads/2015/08/cn900-key-programmer-components-instruction-25.jpg

Attention: TPX4 is used for collecting data. Now you have used this TPX4

collect the data for original key and copy another key succssfully. For

next time, if you want to use TPX4 to collect data, you must clear the

data first. How to clear the data for this TPX4, here is the detailed steps:

1) Put TPX4 on CN900 key programmer just like this photo:

2) Click “SPECIAL” button.

3) Click “GENERATE CODE” button.

4) choose “Blank 7936″

5) click “GENERATE” button

6) click button “GEN”

7) Several seconds later, you will see “Success” on the screen. It means

that data has been erased. And you can use this TPX4 to collect the data

for next time.