SMK NEGERI 3 SINGARAJANo. Dokumen F 22/WKS1/

Revisi ke 0

RENCANA PELAKSANAAN PEMBELAJARAN

(ISO 9001:2000,klausul 7.5)

Tgl. berlaku 30 Juli 2007

Halaman 1 / 8

Nama file RPP/KTSPSubject : English

Class/ Semester : XII /3

Meeting :

Time Allocation : 2 x 40 minutes

Standard Competency : Holding a communication in English in Intermediate level

Basic Competency : Understanding the use of manual tools or equipments through

a series of steps

Indicators :1. Answering questions about a process of how to use manual

tools or equipments (consists of; goal, the

materials/equipments needed, steps)

2. Identifying the basic generic structure of procedure text of

how to use manual tools or equipments

3. Retell the steps of how to use manual tools/equipments

orally in chain

I. Purpose of the Study :

1. Students are able to understand a text entitled “how to change your car’s oil” well.

2. Students are able to answer some questions related to the text correctly

3. Students are able to find some related vocabularies from the text and compare with their

own prior knowledge

4. Students are able mention the generic structure of the text given correctly

5. Students are able to re-arrange some sentences in order to make a good passage about

“how to change your car’s tyre”

6. Students are able to retell the procedure of the previous text in front of the class in chain

with the members of the group

II. Materials

A text entitled How to change your car’s oil (enclosed and it can be changed based on

the students interest)

List of questions and vocabularies (enclosed)

The generic structure of Procedure text:

1. Goal

Goal is a statement that outlines the purpose of the procedures

2. Material/equipments

Materials and equipments are the things which are needed and should be prepared in

the process

3. Steps

Steps are the series of methods in logical and time order in order to achieve the goal

Another text entitled “How to Change Your Car’s Tyre”. (this text will be given in

inappropriate order)

III. Teaching Methods

The methods that will be used are cooperative learning (group discussion, individual work)

and also contextual teaching and learning method (question and answer, performance,

lecture).

IV. Teaching Steps

Pre-activities (10 minutes)

- The teacher greets the students

E.g. good morning students, how are you?

- The teacher checks the students’ attendance

E.g. who is absent? Is there any letter about him/her?

- The teacher checks the cleanliness of the class and makes sure about the condition of

the classroom

- The teacher reminds the students about the topic in the previous day by asking some

questions

E.g. Students, do you still remember about the topic in the previous meeting?

Whilst activities (60 minutes)

a. Exploration (40 minutes)

- The teacher shows an oil can to the students and asks their knowledge about the

things shown.

E.g. Do you know what is this? Have you ever work with this thing?

- The teacher tells the purpose of the meeting at the day

E.g. Well students, today we will learn about how to change your car’s oil

- The teacher distributes a text entitled How to change your car’s oil and asks the

students to read the text loudly

- The teacher leads the students to discuss about the text and understand about the

content of the text

E.g. well students do you understand the text? Is there any difficult words?

- The teacher tells the students to answer the questions given below the text

e.g. Please answer the questions below the text

- The teacher asks a student to come to the front of the class to explain about certain

tools

- The teacher explains about the generic structure of the texts

b. Elaboration (15 minutes)

- The teacher asks the students to make groups which consists of 5 members and asks

them to rearrange some jumbled sentences into a correct text

- The teacher asks some groups to perform in front of the class

c. Confirmation (5 minutes)

- Teacher discusses students’ works and gives revisions toward the mistakes done by

the students

- Teacher repeats once again about the nature of how to use manual tools

- Teacher asks the students whether there’s any misunderstanding experienced by the

students about the teacher’s explanation

Post activities (10 minutes)

- Teacher asks the students to summarize the topic of the day by leading them with

some questions

- Teacher parts the students and gives them homework

V. Teaching Aids

1. Texts (enclosed)

2. Board marker

3. Hand out (English for SMK grade XI Smt 3 and A Practical English Grammar fourth

edition)

4. Written material given by the teacher

5. Some mechanical equipments

VI. Assessment Technique

Point to be assessed

In this meeting the teacher will give score for the students’ performance in front of the

class. Students will perform the result of re-arrangement of certain texts by reading it in

chain. The score really depends on the rubric below:

Rubric

There are five steps that should be arranged by the students. Each correct step will be

scored two. The rubric will be stated below;

Number of Correct Answer in the

Arrangement

Score

5

4

3

2

1

0

10

8

6

4

2

0

The score will be for all the members of the group. The highest score will be 10 and the

lowest one will be 0.

Additional Rubric

This additional rubric will be used in a condition in which a teacher wants to assess the

answers of the questions given about the text. There are 10 questions in part I and there

are another 10 questions in part II. Each correct answer will be scored 1 for all parts.

Then, the score will be added and be divided into 2. The highest score will be 10 and the

lowest one will be 0.

Enclosures

HOW TO CHANGE THE OIL IN YOUR CAR

There are many ways that you can do in order to make your car running well. One of

them is changing the car’s engine oil and filter frequently. The changing process can be done

when there is contamination done by other chemicals unsure. It can also be done depends on

the driving habits of the owner, it can be every 3 months or 3000 miles or can be as long as

24 months or 20.000 miles. Below are the easy steps in changing your car’s oil.

1. First of all, prepare all the equipments and supplies (e.g. plug, filter, socket, wrench,

ratchet, grip, oil pan, etc) under your car in order to ease you to gain them. Be careful

with the hot engine!

2. Open the hood of the car and also the oil filler cap on the top of the engine in order to

ease you to drain the old oil. Then, put the drain plug on the oil pan and place it at the

back of the car engine to catch the oil runoff.

3. The next step is using the socket or wrench to loosen the plug counter. Sometimes, if

the bolt is tight, you can use more leverage like a pipe segment on your ratchet

handle. Be careful not to drop the plug into the oil, because it will be a hard job to

find the plug in the black stuff. If you drop it in the pan, it can be found with a magnet

which is at the end of an expandable rod.

4. The fourth step is replacing the filter. Put off the old filter and then install a new filter

in a good position. There are many notes that you should remember, such as;

a. You have to make sure that the rubber gasket ring comes off with the filler. It

is because when you leave it inside the new filter will not close rightly and

will leak.

b. Dip the tip of your finger in the new oil and smear it on the gasket ring of the

new filter after installing it.

5. Replace the drain plug on the oil pan. Don't forget to install a replacement gasket or

washer. Start threading it with your fingers and it should be snug,

6. This would be a good time to wipe any debris or buildup off the surface where the

gasket will seat. One thing that should be noticed about it is that screw on the new

filter but be careful with the threads. Then make sure also to replace all of them

without any leak. The tight of the screw will be depend on the how it is needed.

7. The next step is you should add new oil to the car at the fill hole. The amount you

need is in the owner's manual, usually listed under "capacities". It commonly depends

on the car’s capacities, it can be 3.5 – 4 litres

8. Replace the fill cap, check around for tools and close the hood.

9. Start the engine for a minute, watching to be sure the oil pressure light goes off after

start-up. It has a purpose on checking the tight of the filler in order not to cause leak.

Part I. Comprehension Questions

1. What are the equipments needed in this process?

2. What will happen if the gasket ring is not comes off with the filler?

3. What is the second step of the procedure?

4. How much oil that should be added to the car?

5. How many steps are there in this procedure?

6. What is the fourth step in the procedure?

7. What can we do if the plug falls into the residue oil?

8. When we should change the oil of our car?

9. What kinds of tools that can be used when the bolt is tight?

10. What is the last step in this procedure?

Key Answer

1. Plug, filter, socket, wrench, ratchet, grip,

2. When you leave the gasket ring inside the new filter will not close rightly and

will leak.

3. The next step is using the socket or wrench to loosen the plug counter.

Sometimes, if the bolt is tight, you can use more leverage like a pipe segment

on your ratchet handle

4. It is based on the manual book or based on the capacity of the car (commonly

3.5-4 litres

5. There are nine main steps

6. The fourth step is replacing the filter. Put off the old filter and then install a

new filter in a good position.

7. We can use magnet which is put at the end of the expandable rod and can also

use funnel with screening in it

8. It depends on the driving habit of the owner, can be every 3000 miles or

20.000 miles. It can also be done when the oil break down or contaminated

9. Socket or wrench which has been added to a pipe in order to ease us to loosen

it

10. Close the hood of the car and check whether there is any leak or not and also

checks for the oil pressure

Part II. Please find the English terms for the words below.

1. Oli: ….

2. Saringan:…..

3. Peralatan:…..

4. Mesin:…….

5. Baut:…..

6. Kunci Inggris:….

7. Mengendurkan:….

8. Kebocoran:…..

9. Kap mobil:….

10. Tekanan Oli:…..

Key Answer

1. Oil

2. Filter

3. Equipment

4. Engine

5. Bolt

6. Wrench

7. Loosen

8. Leak

9. Hood

10. Oil Pressure

The second text that will be arranged in inappropriate order which will become a group

assignment for the students.

How to Change Your Car’s Tyre

1. The first step in changing the car’s tyre is prepare all the equipments that we need like

jack, wrench, a new tyre

2. Then, use the wrench to loosen the four tyre moors to the left direction but the tyre

will not be opened yet

3. The next step is jacks up the tyre in order to make the position of the tyre higher and

ease us to change it

4. After jacking the tyre up until the right position, we can continue to loosen the bolts

and the moors and put off the old tyre

5. Finally, install a new tyre and start threading the bolts and the moors but do it in

opposite position until it is tightened well

Mengetahui, Singaraja, 3 Oktober2009

Guru Pamong Mahasiswa Prakerin

Yulistini, S.Pd Putu Ayu Siska Paramita NIP. 19650708 198902 2 002 NIM 0612021018

Dosen Pembimbing

I.P.N Wage Myartawan NIP. 132 320 117